Formation of porous polymer morphology by microsyneresis during divinylbenzene polymerization

This article describes the investigation of the importance of various reaction conditions on microsyneretic pore formation during polymerization of divinylbenzene (DVB) under so‐called “solvothermal” conditions. To induce microsyneretic pore formation, the most important parameter is an unusually high dilution of monomers with a “good” porogen solvating the polymer chains. High dilution and solvation of the growing poly(DVB) chains promote the prolongation of the polymer chains rather than their interconnection by crosslinking. Consequently, when the polymer gel density reaches the point where syneresis starts, the polymer network is geometrically too extensive to be broken up into precipitating entities and, instead, porogen droplets are formed within the continuous polymer gel. The pore geometry created by microsyneresis offers high surface area in wide mesopores and hence, high capacity for supporting functional groups or reactions with much better accessibility than narrow pores between polymer microspheres produced by macrosyneresis in conventional styrenic polymer supports. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 774–781     

Enhancing the Water Stability of Al‐MIL‐101‐NH2 via Postsynthetic Modification

The resistance of metal–organic frameworks towards water is a very critical issue concerning their practical use. Recently, it was shown for microporous MOFs that the water stability could be increased by introducing hydrophobic pendant groups. Here, we demonstrate a remarkable stabilisation of the mesoporous MOF Al‐MIL‐101‐NH₂ by postsynthetic modification with phenyl isocyanate. In this process 86 % of the amino groups were converted into phenylurea units. As a consequence, the long‐term stability of Al‐MIL‐101‐URPh in liquid water could be extended beyond a week. In water saturated atmospheres Al‐MIL‐101‐URPh decomposed at least 12‐times slower than the unfunctionalised analogue. To study the underlying processes both materials were characterised by Ar, N₂ and H₂O sorption measurements, powder X‐ray diffraction, thermogravimetric and chemical analysis as well as solid‐state NMR and IR spectroscopy. Postsynthetic modification decreased the BET equivalent surface area from 3363 to 1555 m² g^?1 for Al‐MIL‐101‐URPh and reduced the mean diameters of the mesopores by 0.6 nm without degrading the structure significantly and reducing thermal stability. In spite of similar water uptake capacities, the relative humidity‐dependent uptake of Al‐MIL‐101‐URPh is slowed and occurs at higher relative humidity values. In combination with ¹H‐²⁷Al D ‐HMQC NMR spectroscopy experiments this favours a shielding mechanism of the Al clusters by the pendant phenyl groups and rules out pore blocking.     

基于DIS数字信息化系统对透光物质透光性能的研究

采用DIS数字信息化系统,对不同浓度的蓝墨水溶液在激光光源照射下的透射平均照度及照度分布图像进行实验研究,得到了平均照度值随溶液浓度变化的规律。对不同颜色塑料膜片对白炽灯光源透过照度值及照度分布图像进行实验研究得到及其相关之规律。     

Extrusion of pastes with a piston extruder for the determination of the local solid and fluid concentration, the local porosity and saturation and displacement profiles by means of NMR imaging

 Nuclear Magnetic Resonance (NMR) was used to investigate the extrusion behaviour of PTFE pastes in a ram extruder. By means of ¹H-NMR imaging (MRI) it is possible to determine the local proton density and therefore, the local fluid concentration. The ¹⁹F-MRI provides the local solid concentration. Thus the local saturation and the local porosity can be calculated with the information of the local fluid and solid concentration. Furthermore displacement profiles can be derived from NMR images by means of correlation techniques without any preparation or marking of the pastes. Received: 8 May 2000   Accepted: 1 May 2001     

Stress-Strain State in the Zone of Load Transfer in a Composite Specimen under Uniaxial Tension

The stress-strain state in the zone of load transfer in a uniaxially stretched specimen made of a unidirectional epoxy carbon-fiber-reinforced plastic (CFRP) is investigated. A parametric analysis of the influence of geometric and mechanical characteristics of the specimen on its stress-strain state is performed by means of finite-element modeling. The parameters allowing us to significantly reduce the dangerous concentration of transverse and tangential stresses are revealed. The mechanical tensile characteristics of a high-strength pultruded unidirectional CFRP are determined experimentally, and the size effect of its strength is estimated.     

Diffusion in poro‐plastic media

A model is developed for the flow of a slightly compressible fluid through a saturated inelastic porous medium. The initial‐boundary‐value problem is a system that consists of the diffusion equation for the fluid coupled to the momentum equation for the porous solid together with a constitutive law which includes a possibly hysteretic relation of elasto‐visco‐plastic type. The variational form of this problem in Hilbert space is a non‐linear evolution equation for which the existence and uniqueness of a global strong solution is proved by means of monotonicity methods. Various degenerate situations are permitted, such as incompressible fluid, negligible porosity, or a quasi‐static momentum equation. The essential sufficient conditions for the well‐posedness of the system consist of an ellipticity condition on the term for diffusion of fluid and either a viscous or a hardening assumption in the constitutive relation for the porous solid. Copyright © 2004 John Wiley & Sons, Ltd.     

三维流动传热空隙率计算程序FASTOR—3D开发研究

1引言大粘度（大r）和大系数（ss和sc）法是处理流动区域中障碍物的常用方法山。但当流动区域中障碍物数量较多时，宜采用空隙率来模拟障碍物，如模拟反应堆流动传热的商用程序COMMIX［’］。我们根据空隙率模拟的基本概念，针对采用交错网格的压力校正法，自行编制了多障碍物流动传热三维计算的全部源程序代码，应用于某核反应堆钠池流动传热的数值模拟，获得了比较合理的结果。2数学模型和数值方法2．1控制方程空隙率修整的质量、动量、能量及湍流动能与耗散率的守恒方程通式的三维柱坐标形式为其中中一1，。，。，。，T，k，。分别表…     

Adaptive remeshing for ductile fracture prediction in metal formingRemaillage adaptatif pour la prévision de la rupture ductile en mise en forme

The analysis of mechanical structures using the Finite Element Method in the framework of large elastoplastic strain, needs frequent remeshing of the deformed domain during computation. Indeed, the remeshing is due to the large geometrical distortion of finite elements and the adaptation to the physical behavior of the solution. This paper gives the necessary steps to remesh a mechanical structure during large elastoplastic deformations with damage. An important part of this process is constituted by geometrical and physical error estimates. The proposed method is integrated in a computational environment using the ABAQUS/Explicit solver and the BL2D-V2 adaptive mesher. To cite this article: H. Borouchaki et al., C. R. Mecanique 330 (2002) 709–716.     

Consolidation around a borehole embedded in media with double porosity under release of geostatic stresses

The paper deals with the stress, displacement, pore and fissure pressures fields induced by the drilling and/or the pressurization of a vertical borehole in a formation of water-saturated porous media with double porosity. The solution includes the boundary condition of non-hydrostatic in situ state of stress. The solid skeleton is assumed to behave as a linearly poroelastic material with compressible constituents. The analytical solution is derived in Laplace’s space and transformed to the time domain using a numerical inversion technique. The histories of pore and fissure pressures are illustrated to show the influence of permeabilities of the pore and fissure systems.     

Dislocation unpinning model of acoustic emission from alkali halide crystals

The present paper reports the dislocation unpinning model of acoustic emission (AE) from alkali halide crystals. Equations are derived for the strain dependence of the transient AE pulse rate, peak value of the AE pulse rate and the total number of AE pulse emitted. It is found that the AE pulse rate should be maximum for a particular strain of the crystals. The peak value of the AE pulse rate should depend on the volume and strain rate of the crystals, and also on the pinning time of dislocations. Since the pinning time of dislocations decreases with increasing strain rate, the AE pulse rate should be weakly dependent on the strain rate of the crystals. The total number of AE should increase linearly with deformation and then it should attain a saturation value for the large deformation. By measuring the strain dependence of the AE pulse rate at a fixed strain rate, the time constantτ _s for surface annihilation of dislocations and the pinning timeτ _p of the dislocations can be determined. A good agreement is found between the theoretical and experimental results related to the AE from alkali halide crystals.