A WKB analysis of the buckling condition for a cylindrical shell of arbitrary thickness subjected to an external pressure

We consider the plane-strain buckling of a cylindrical shellof arbitrary thickness which is made of a Varga material andis subjected to an external hydrostatic pressure on its outersurface. The WKB method is used to solve the eigenvalue problemthat results from the linear bifurcation analysis. We show thatthe circular cross-section buckles into a non-circular shapeat a value of µ₁ which depends on A₁/A₂ and a mode number,where A₁ and A₂ are the undeformed inner and outer radii, andµ₁ is the ratio of the deformed inner radius to A₁. Inthe large mode number limit, we find that the dependence ofµ₁ on A₁/A₂ has a boundary layer structure: it is constantover almost the entire region of 0 < A₁/A₂ < 1 and decreasessharply from this constant value to unity as A₁/A₂ tends tounity. Our asymptotic results for A₁ – 1 = O(1) and A₁– 1 = O(1/n) are shown to agree with the numerical resultsobtained by using the compound matrix method.     

Fully developed mixed convection in horizontal and inclined tubes with uniform heat flux using nanofluid

Fully developed laminar mixed convection of a nanofluid consists of water and Al₂O₃ in horizontal and inclined tubes has been studied numerically. Three-dimensional elliptic governing equations have been solved to investigate the flow behaviors over a wide range of the Grashof and Reynolds numbers. Comparisons with previously published experimental and numerical works on mixed convection in a horizontal and inclined tube are performed and good agreements between the results are observed. Effects of nanoparticles concentration and tube inclinations on the hydrodynamics and thermal parameters are presented and discussed. It is shown that the nanoparticles concentration does not have significant effects on the hydrodynamics parameters. Heat transfer coefficient increases by 15% at 4 Vol.% Al₂O₃. Skin friction coefficient continually increases with the tube inclination, but the heat transfer coefficient reaches a maximum at the inclination angle of 45°.     

Carbide precipitates in solution-quenched PH13-8 Mo stainless steel: A small-angle neutron scattering investigation

This paper deals with the small-angle neutron scattering (SANS) investigation on solution-quenched PH13-8 Mo stainless steel. From the nature of the variation of the functionality of the profiles for varying specimen thickness and also from the transmission electron microscopy (TEM), it has been established that the small-angle scattering signal predominantly originates from the block-like metallic carbide precipitates in the specimen. The contribution due to double Bragg reflection is not significant in the present case. The single scattering profile has been extracted from the experimental profiles corresponding to different values of specimen thickness. In order to avoid complexity and non-uniqueness of the multi-parameter minimization for randomly oriented polydisperse block-like precipitate model, the data have been analyzed assuming randomly oriented polydisperse cylindrical particle model with a locked aspect ratio.     

Influence of oxidation time on semiconductive behaviour of thermally grown oxide films on AISI 304L

The oxide films formed on AISI 304L stainless steel at 300 °C in the oxidation time range between 2 and 4 h have been studied by photoelectrochemistry. Photocurrents were investigated as a function of the wavelength of the incident light and the electrode potential. The investigation allowed the determination of the semiconductive properties of the oxides. The oxide films showed n-type behaviour. A duplex structure of the oxide films has been suggested on the basis of the photocurrent spectra, with an internal oxide layer having an optical gap (E_g2 = 2.16-2.3 eV) depending on the applied potential and oxidation time, higher to that of the external oxide layer (E_g1 ≈ 1.9 eV). Significant variations in the amplitude of the photocurrent were detected as a function of the applied potential and the oxidation time.     

轻型汽车后桥半轴断裂件的组织及断口特征

采用光学显微镜和扫描电子显微镜等手段，对某轻型汽车40Cr后桥半轴断裂件的组织及断口特征进行了分析结果表明：半轴在调质处理时的淬火温度不够高，使其表层和心部组织中存在较多的铁素体相，造成了工件最终的硬度和疲劳强度不足，导致半轴在使用中发生扭转疲劳断裂．     

Letter: Models of Relativistic Particle with Curvature and Torsion Revisited

Models, describing relativistic particles, where Lagrangian densities depend linearly on both the curvature and the torsion of the trajectories, are revisited in D=3 space forms. The moduli spaces of trajectories are completely and explicitly determined using the Lancret program. The moduli subspaces of closed solitons in the three sphere are also determined.     

Rugged distal tips for CO2 laser medicine

Low-loss and rugged distal tips for CO₂ laser have been proposed and fabricated based on a commercially available stainless steel (St) pipe. A method of smoothening the inner surface of the St pipe with a rough inner surface is put forward. Fabrication parameters, transmission properties, and mechanical strength of the cyclic olefin polymer-coated silver hollow St distal tip are experimentally discussed.     

大型钢结构人行景观天桥的有限元分析

采用有限元方法对大型钢结构人行景观天桥进行了静力学、温度应力、动力学模态和初步的抗震能力分析,并就桥自重作用下的最大竖向位移和实际观测结果进行了比较,两者是一致的.计算结果表明:人行景观天桥在常规、温度极值改变和多遇地震荷载作用等多种工况下,现有的设计方案具有足够的强度、刚度和抗震能力.     

Effect of hydrogen on interatomic bonds in austenitic steels

Mössbauer spectroscopy was used to investigate the influence of dissolved hydrogen on the interatomic bonds in austenitic steels. It was carried out to prove the decohesion mechanism of hydrogen embrittlement (HE). It is shown that hydrogen increases Debye temperature, i.e., the interatomic bonds in hydrogenated austenitic steel becomes stronger.     

三维内肋管内插入螺旋扭带的强化传热实验

本文分别以水和乙二醇为工质，在Ｒｅ数范围为：６００～４００００，Ｐｒ数范围为：５．５～１１０之间，对四根分别插入三种不同扭率螺旋扭带的三维内助管内的换热和流阻特性进行了实验研究。结果表明：三维内肋管内加装扭带的强化传热技术适用于低Ｒｅ数下高Ｐｒ数工质的管内对流换热强化。根据实验值得到了流阻和换热关联式。