用等厚干涉测定液体折射率

介绍一种采用等厚干涉原理测定液体折射率的简单可靠的方法。     

环状连续强激光下光学薄膜的瞬温和热畸变

详细研究了非冷却光学薄膜元件在环形激光光束辐照下的瞬态温度分布和随后的热畸变，并且用泰曼干涉仪实际测量了连续波氧碘激光辐照各种非冷却光学元件的热畸变量并与理论计算相比较，分析结果表明理论和实验相一致。     

Indirect Methods For Determination of The Protective Effects of Coating Films on The Surface of Crystals

The extents of the protective effects of coating films on the surface of crystals were determined. Three different samples were made with different quantities of coating fluid (Sepifilm LP 010 in 10% aqueous solution). Since the atomizing rate was constant, the coating time increased in parallel with the volume of coating fluid applied. The direct measurement of film thickness and smoothness is very difficult, and therefore indirect methods were used. Dimenhydrinate was chosen as model drug; this is a heat-sensitive antihistamine with a low melting point. This temperature can be reached during the tableting process. The behaviour of samples on exposure to heat was examined by differential scanning calorimetry. The water uptakes of the samples were determined with an Enslin apparatus. Plasticity was studied with an instrumented tablet machine. These indirect methods (thermal conductivity, water uptake and plasticity measurements) revealed connections between the results of the various experiments. An overlong coating time decreased the protective effect of the coating film. This revised version was published online in August 2006 with corrections to the Cover Date.     

宽带膜厚实时监控过程中膜层折射率的确定方法

为了准确计算出镀膜过程中每层膜的折射率，介绍了实时监控过程中确定膜层折射率的2种方法：一种是由实测的透射比光谱直接反算出膜层的折射率；另一种是用最小二乘法的优化算法实时拟合折射率。试验结果表明：在线反算适合单点监控，所得折射率误差小于2%。然而在实际镀膜过程中,由于宽带内膜层参数误差较大,一般大于25%。为此，采用最小二乘法拟合，即在整个宽光谱范围内采集每个波长点的信息，所得结果误差很小，一般都在2％～5%之间,有时可达到10%,在很大程度上提高了实际镀膜时膜厚监控的精度。     

厚度对非极性聚合物薄膜驻极体电荷储存及电荷动态特性的影响

以Du Pont公司的商用Teflon FEP A型薄膜为例，通过热脉冲技术、等温表面电位衰减测量和开路热刺激放电电流谱分析等实验结果，讨论了经常温和高温电晕充电后样品厚度对薄膜驻极体的沉积电荷密度、薄膜驻极体的内电场、体电导率以及电荷储存稳定性的影响.通过热脉冲技术组合电导率温度曲线的测量，研究了在不同温度条件下样品厚度对沉积电荷层的平均电荷重心移动的影响.结果表明：在充电参数一定的条件下，随着膜厚的降低，储存电荷密度上升，但电荷稳定性有所下降.因此，合理地调控薄膜厚度，可以有效地优化驻极体的电荷储存能 关键词： 厚度 驻极体 电荷储存能力 电荷稳定性     

Optimal design of a convergent-barrel cold spray nozzle by numerical method

A convergent-barrel (CB) cold spray nozzle was designed through numerical simulation. It was found that the main factors influencing significantly particle velocity and temperature include the length and diameter of the barrel section, the nature of the accelerating gas and its pressure and temperature, and the particle size. Particles can achieve a relatively low velocity but a high temperature under the same gas pressure using a CB nozzle compared to a convergent-divergent (CD) nozzle. The experiment results with Cu powder using the designed CB nozzle confirmed that particle deposition can be realized under a lower gas pressure with a CB nozzle.     

Fabrication of patterned gold electrodes with spin-coated-and-fired Au(1 1 1) film by the soft lithography

We prepared high quality Au(1 1 1) film on Si wafer through the spin coating and thermal decomposition of a gold ink, spin-coated-and-fired (SCAF) Au film. The X-ray measurements, XRD and pole-figure analysis, showed that the SCAF Au film has a (1 1 1) out-of-plane orientation with a random in-plane orientation. In order to confirm the chemical activity of the SCAF Au film, we demonstrate the formation of patterned structures with the film by using soft lithography technique. The chemical activities of this physically stable SCAF Au film to the alkanethiols were at least equivalent those of physically deposited the Au films. The possibility of the mass production of micro patterned structure with the SCAF Au film was also demonstrated over the wide region on Si wafer by the microcontact lithography. These suggest that the Au film will help the easy fabrication of various nanosized devices on Si wafer and other substrates.     

Studies on calcium‐containing poly(urethane ether)s

The calcium salt of mono(hydroxyethoxyethyl)phthalate [Ca(HEEP)₂] was synthesized by the reaction of diethylene glycol, phthalic anhydride, and calcium acetate. Calcium‐containing poly(urethane ether)s (PUEs) were synthesized by the reaction of hexamethylene diisocyanate (HMDI) or tolylene 2,4‐diisocyanate (TDI) with a mixture of Ca(HEEP)₂ and poly(ethylene glycol) (PEG₃₀₀ or PEG₄₀₀) with di‐n‐butyltin dilaurate as a catalyst. A series of calcium‐containing PUEs of different compositions were synthesized with Ca(HEEP)₂/PEG₃₀₀ (or PEG₄₀₀)/diisocyanate (HMDI or TDI) molar ratios of 2:2:4, 3:1:4, and 1:3:4 so that the coating properties of the PUEs could be studied. Blank PUEs without calcium‐containing ionic diols were also prepared by the reaction of PEG₃₀₀ or PEG₄₀₀ with HMDI or TDI. The PUEs were well characterized by Fourier transform infrared, ¹H and ¹³C NMR, solid‐state cross‐polarity/magic‐angle‐spinning ¹³C NMR, viscosity, solubility, and X‐ray diffraction studies. The thermal properties of the polymers were also studied with thermogravimetric analysis and differential scanning calorimetry. The PUEs were applied as top coats on acrylic‐coated leather, and their physicomechanical properties were also studied. The coating properties of PUEs, such as the tensile strength, elongation at break, tear strength, water vapor permeability, flexing endurance, cold crack resistance, abrasion resistance, color fastness, and adhesive strength, were better than the standard values. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 2865–2878, 2003     

摄像型等厚干涉实验仪器的研究

介绍了“摄像型等厚干涉实验仪”的构造及等厚干涉实验新的测量方法。     

Microstructure and high-temperature wear resistance of a laser surface alloyed γ-TiAl with carbon

TiC reinforced composite coating on γ-TiAl alloy was successfully fabricated by laser surface alloying with carbon. The fine TiC reinforcing phase had a gradient distribution in the coating, and its growth morphology of TiC in laser surface alloyed coating was in unique faceted platelet-like. The composite coating exhibited high hardness and excellent high-temperature sliding wear resistance.