迈克尔逊干涉仪中补偿板与干涉条纹

通过分析缺失补偿板的迈克尔逊干涉仪中的附加光程差,推出干涉条纹满足的方程式,并用计算机模拟了动镜移动过程中变化的干涉条纹,与实验结果相一致.     

Strain hardening of polycarbonate in the glassy state: Influence of temperature and molecular weight

This study is concerned with the temperature and molecular weight dependence of the strain-hardening behavior of polycarbonate. It is shown that the strain-hardening modulus reduces with increasing temperature and decreasing molecular weight. This result is interpreted in terms of temperature accelerated relaxation of the entanglement network. Moreover, it is shown that frozen-in orientations, induced by homogeneous deformations above the glass transition temperature, lead to anisotropic yield behavior that can be fully rationalized (and modelled) in terms of a superimposed stress contribution of the prestrained network. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 2041–2049, 2004     

承受拉-扭组合载荷的薄壁圆筒屈服时产生塑性流动的条件

提出了在无外力作功的情况下，具有Bauschinger效应的弹塑性材料处于屈服状态产生自发的塑性流动时应满足的条件．这个条件不仅与材料的力学性能有关，而且还处决于材料的具体的载荷边界条件和变形．举例说明了承受拉一扭组合的薄壁圆筒中，采用组合强化模型时，产生塑性流动的具体条件．     

工业CT图像均匀性校正

在工业CT图像重建过程中,射束硬化使得图像出现“杯状”伪影,阵列探测器响应不一致使得图像出现环状伪影、带状伪影和点伪影,影响图像均匀性.本文分析了射束硬化的原理和探测器响应不一致的数学模型,并通过实验,对探测器响应进行多挡板定标得到校正系数表.利用查表插值的方法对投影数据进行均匀性校正,消除上述伪影.     

Problems of an additional experiment

In some situations estimates of unknown parameters must be corrected by additional measurements. It is in principle no problem to calculate the corrected estimates, however, it is of more interest to find formulae for correction itself. The formulae enable us to design an additional experiment and to judge its usefulness. The aim of the paper is to find such formulae for several situations. Supported by the grant of the Council of Czech Government MSM 6 198 959 214.     

Dislocation-density-based constitutive modelling of tensile flow and work-hardening behaviour of P92 steel

The flow and work-hardening behaviour of tempered martensitic P92 steel have been investigated using phenomenological constitutive model in the temperature range 300–873 K for the strain rates ranging from 3.16 × 10^?5 to 1.26 × 10^?3 s^?1. The analysis indicated that the hybrid model reduced to Estrin–Mecking (E–M) one-internal-variable model at intermediate and high temperatures. Further, the analysis also indicated that dislocation dense martensite lath/cell boundaries and precipitates together act as effective barriers to dislocation glide in P92 steel. The flow behaviour of the steel was adequately described by the E–M approach for the range of temperatures and strain rates examined. Three distinct temperature regimes have been obtained for the variations in work-hardening parameters with respect to temperature and strain rate. Signatures of dynamic strain ageing in terms of the anomalous variations in work-hardening parameters at intermediate temperatures and the dominance of dynamic recovery at high temperatures have been observed. The evaluation of activation energy suggested that deformation is controlled by the dominance of cross-slip of dislocations at room and intermediate temperatures, and climb of dislocations at high temperatures.     

Green solvent approach for printable large deformation thermoplastic elastomer based piezoresistive sensors and their suitability for biomedical applications

Composites based on biocompatible thermoplastic elastomer styrene‐ethylene/butylene‐styrene (SEBS) as matrix and multi‐walled carbon nanotubes (MWCNT) as nanofillers show excellent mechanical and piezoresistive properties from low to large deformations. The MWCNT/SEBS composites have been prepared following a green solvent approach, to extend their range of applicability to biomedical applications. The obtained composites with 2, 4, and 5 wt % MWCNT content provide suitable piezoresistive response up to 80% deformation with a piezoresistive sensibility near 2.7, depending on the applied strain and MWCNT content. Composite sensors were also developed by spray and screen printing and integrated with an electronic data acquisition system with RF communication. The possibility to accurately control the composites properties and performance by varying MWCNT content, viscosity, and mechanical properties of the polymer matrix, shows the large potential of the system for the development of large deformation printable piezoresistive sensors. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016 , 54, 2092–2103     

A Tensile Strain Hardening Test Indicator of Environmental Stress Cracking Resistance

Environmental stress cracking resistance (ESCR) is an important indicator of performance for high density polyethylene (HDPE) in structural and polymer pipe applications. The commonly used test for determining ESCR of HDPE can be time consuming and rather imprecise. A tensile strain hardening test was recently proposed to offer a faster way to characterize ESCR of polyethylene. In this paper, a practical approach is adopted whereby the test is extended to room temperature and shown to relate reliably to the ESCR of HDPE. Several HDPE resins (including pipe‐grade resins) are analyzed at strain rates of 0.5 mm/min and 7 mm/min to compare the effect of strain rate. Comparisons between the conventional ESCR test method and the strain hardening test show that strain hardening can be used to rank ESCR of HDPE in a reliable fashion. In our study the more direct measure of “hardening stiffness” is used to compare resins instead of strain hardening modulus. Because no true stress‐strain measurement is needed, this is a much simpler test method than other methods previously suggested. In addition, the use of the natural drawing ratio (NDR) as ESCR ranking indicator is examined. Results show that NDR can also be employed as a strain rate‐independent indicator of ESCR of HDPE. The test proposed herein is practical, simple and precise, and hence a more reliable indicator of ESCR performance of HDPE.     

酸催化溶胶-凝胶法制备高强度SiO2增透膜研究进展

高强度增透膜是用于减少表面反射、增加光线透光率的薄膜,具有密度低、折射率可调、耐磨性好的特点.本文综述了高强度增透膜的制备方法与研究进展,介绍了酸催化溶胶-凝胶法制备SiO2溶胶的机理及影响因素,酸催化溶胶-凝胶法及两种辅助酸催化溶胶-凝胶法制备高强度增透膜的方法,对高强增透膜制备的发展方向和应用前景进行了展望.