A novel and efficient synthesis of porphine

meso-Tetra(n-hexyloxycarbonyl)porphyrin was found to be converted into porphine, the mother compound of porphyrins, in a 77% yield when heated in aqueous sulfuric acid at 180 °C over 30 min under an inert atmosphere. The observation demonstrates that the substituted porphyrin serves as a novel and useful precursor for porphine.     

A note on the unsteady boundary layers over a flat plate

The unsteady boundary layer over a semi-infinite flat plate was investigated in this paper. The flow involves the unsteady flow over a flat plate with leading edge accretion or ablation. The momentum boundary layer was further analyzed and it was shown that the leading edge ablation had a similar effect to the wall mass injection or upstream wall movement making the fluid blown away from the wall. The thermal boundary layer of the same flow was also studied. Results show that the leading edge accretion or ablation can greatly change the fluid motion and the heat transfer characteristics.     

Modeling of radiative heat transfer in an axisymmetric cylindrical enclosure with participating medium

Radiative heat transfer in an axisymmetric enclosure with absorbing, emitting, and scattering medium is studied here by using the different methods such as MDOM, FVM, and MFVM with emphasis on the treatment of angular derivative term, which appears in curvilinear coordinates due to angular redistribution. After final discretization equation for MFVM is introduced by using the step scheme and directional weights, the present approach is validated by applying it to three different benchmarking problems with absorbing, emitting, and scattering medium. All of the results presented here support its accuracy as well as moderate efficiency. Finally, the present approaches are applied to a truncated cone-shaped enclosure as a body-fitted geometry case.     

Intrinsic thermal stability and quenching recovery of thin-film superconductors with thermal boundary resistance

The stability behaviour of a thin-film superconductor under a localized release of thermal disturbance is investigated. Two-dimensional conjugate film/substrate conduction equation with anisotropic thermal conductivity of the film, and Joule heat are employed to investigate effects of substrate and thermal properties on the intrinsic stability and quenching recovery. To consider the thermal boundary resistance between film and substrate, an interfacial-layer model (ILM) with very low diffusivity and an acoustic mismatch model (AMM) are employed. Results show that the thermal boundary resistance influences strongly the intrinsic stability. Thermal boundary resistance increases intrinsic stability if the thermal conductivity of the substrate or the disturbance energy is large. Higher Biot numbers and thermal conductivity ratios of film to substrate in longitudinal direction influence stability favorably. We demonstrate also that operation of a film/substrate system, such as YBCO/MgO, is either intrinsically stable or irrecoverably unstable.The authors wish to express their sincere appreciation to Dr. R. C. Chen for his invaluable advice and suggestions during the course of this paper. This research was supported by the National Science Council of the R. O. C. through grant NSC 83-0401-E-009-006. The computations were performed on the IBM ES/9000 at the National Center For High-Performance Computing.     

微通道板真空体电阻与Ⅱ代倒象微光管匹配关系的研究

国内研制的20/30Ⅱ代倒象微光管经常出现微通道板真空体电阻偏高或偏低的问题,直接影响Ⅱ代倒象微光管荧光屏的亮度和目标分辨力,严重影响微光管的质量。经过对20/30Ⅱ代倒象微光管的研制和理论分析,证明英国马拉德公司对用于××1383Ⅱ代倒象微光管的H36微通道板技术条件中真空体电阻技术指标的规定也存在一定的问题。本文从目前国内外工艺水平和有关文献资料的分析出发,进行专题研究。本文中所推导的计算公式和对文献资料提供的技术数据的推导分析,同样适用于其他型号微通道板的真空体电阻与相应Ⅱ代、Ⅲ代微光管匹配关系的计算与研究。     

Characterization of ceramic PVD thin films on AZ31 magnesium alloys

Ceramic thin films have been widely used to protect the metal substrate as coatings in the past years. In order to improve the poor corrosion resistance of AZ31 magnesium alloy, the study in this paper used the electron beam evaporation method to prepare ceramic PVD films on its surface with TiO₂ and Al₂O₃ as donors, respectively. Atomic force microscopy (AFM), scanning electron microscope (SEM), energy dispersive X-ray spectrometer (EDS), Auger electron spectroscopy (AES) and X-ray diffraction (XRD) were used to investigate the surface morphology, composition and microstructure of the thin films. Both films deposited on AZ31 took on compact top surface morphologies and grew as amorphous structures on substrate. AES test not only showed that films compositions deviated the standard stoichiometric ratios, but also found that element Mg diffused into films and existed as magnesium oxide in the TiO_x film as well as the AlO_x film. In the electrochemical corrosion test, the AlO_x coating on AZ31 exhibited the largest electrochemical impedance in a 3.5% NaCl solution. But it did not show better corrosion resistance than others for the poorer adhesion. Even if its thickness was small, the TiO_x coating on AZ31 exhibited the best corrosion resistance in this study. According to the observation and analysis, the damage of these films on AZ31 in aggressive solutions was mainly due to the existence of pores, microcracks, vacancies and poor adhesion between coating and substrate.     

Annealing and measurement temperature dependence of W2B5-based rectifying contacts to n-GaN

The thermal stability and measurement temperature dependence of Schottky contact characteristics on n-GaN using a W₂B₅/Ti/Au metallization scheme was studied using current-voltage (I-V), scanning electron microscopy (SEM) and Auger electron spectroscopy (AES) measurements. The elemental profile obtained from samples annealed at 350 °C showed some titanium diffusion into the gold layer but little other difference from the as-deposited wafer. Annealing at 700 °C produced significant diffusion of titanium. The Schottky barrier height increased with anneal temperature up to 200 °C, reaching a maximum value of 0.65 eV, but decreased at higher annealing temperatures. The reverse breakdown voltage from diodes fabricated using the W₂B₅-based contacts showed a similar dependence. The reverse current magnitude was larger than predicted by thermionic emission alone. The barrier height showed only minor changes with measurement temperature up to 150 °C.     

<Emphasis Type="Italic">Comment on</Emphasis>¶Low temperature specific heat of blue bronze K <Emphasis Type="Bold">0.30</Emphasis>MoO <Emphasis Type="Bold">3</Emphasis>, by J. Odin,J.C. Lasjaunias,K. Biljaković, K. Hasselbach,and P. Monceau

Eur. Phys. J. B 24, 315 (2001) Here we comment on a recently published paper on the presence of a phason contribution in the low temperature heat capacity data of the charge-density-wave compounds K_0.3MoO₃ and (TaSe₄)₂I. We have shown that the anomaly in the C _P / T ³ data reported by Odin et al. is straightforwardly interpreted in terms of low energy phonon modes resulting from the peculiar topology of these compounds. Received 21 February 2002 Published online 19 July 2002     

Adhesion studies of latex film surfaces on the meso- and nanoscale

In this paper the effects of surface roughness and annealing temperature (T) of latex coating films on adhesion are discussed for the different stages of the film formation process. The surface free energy of latex films was assessed in terms of practical work of adhesion (W) (or adherence) using a custom-built adhesion-testing device (ATD), atomic force microscopy (AFM), and contact angle measurements. For preannealed latex films surface roughness averages (R_a) were determined from AFM height images and were related to the values of W obtained from ATD measurements at room temperature. The results obtained using these tests exhibiting surface behavior on different length scales indicate a dependence of the measured adhesion on surface roughness and temperature, as well as on the length scale of the measurements.First preannealed samples were studied, which were obtained by heat treatment above the respective glass transition temperatures (T_g). Increasing the temperature of preannealing resulted in a decrease of the adherence observed in ATD experiments at room temperature. However, on the nanoscale, using AFM, no significant variation of the adherence was observed. This observation can be explained by roughness arguments. Preannealing decreases roughness which results in lower adherence values measured by ATD while for essentially single asperity AFM experiments roughness has an insignificant effect. Specimens were also annealed over a constant period of time (90 min) at different temperatures. At the end of the heat treatment, adhesion was measured at the treatment temperature by ATD. The amplified effect of temperature observed in this case on adherence is attributed to the combination of roughness decrease and increasing test temperature. In a third set of experiments completely annealed samples were studied by ATD as well as by AFM as a function of temperature. With increasing T values ATD showed a decrease in adherence, which is attributed to a decreasing surface free energy of the annealed films at elevated T values. AFM, on the other hand, showed an opposite trend which is assigned to increasing penetration of the tip into the tip/wetting polymer samples versus increasing temperature. Finally, annealing isotherms as a function of time were investigated by ATD in situ at different temperatures. This last set of experiments allowed us to optimize annealing time and temperature to achieve complete curing.