Interface and defects engineering for multilayer laser coatings

High-reflective multilayer laser coatings are widely used in advanced optical systems from high power laser facilities to high precision metrology systems. However, the real interface quality and defects will significantly affect absorption/scattering losses and laser induced damage thresholds of multilayer coatings. With the recent advances in the control of coating design and deposition processes, these coating properties can be significantly improved when properly engineered the interface and defects. This paper reviews the recent progress in the physics of laser damage, optical losses and environmental stability involved in multilayer reflective coatings for high power nanosecond near-infrared lasers. We first provide an overview of the layer growth mechanisms, ways to control the microstructures and reduce layer roughness, as well as the nature of defects which are critical to the optical loss and laser induced damage. Then an overview of interface engineering based on the design of coating structure and the regulation of deposition materials reveals their ability to improve the laser induced damage threshold, reduce the backscattering, and realize the desirable properties of environmental stability and exceptional multifunctionality. Moreover, we describe the recent progress in the laser damage and scattering mechanism of nodule defects and give the approaches to suppress the defect-induced damage and scattering of the multilayer laser coatings. Finally, the present challenges and limitations of high-performance multilayer laser coatings are highlighted, along with the comments on likely trends in future.     

Calcium-based coordination polymers from a solvothermal synthesis of HKUST-1 in 3D printed autoclaves

A mixed-metal 1D coordination polymer [CaCu(HBTC)₂(H2O)₈]_n (where H₃BTC – benzene-1,3,5-tric arboxylic acid) was obtained in a solvothermal synthesis of a well-known copper-containing metal–organic framework [Cu₃(BTC)₂(H₂O)₃]_n (HKUST-1) in autoclaves 3D-printed from commercial polypropylene. This material was a source of calcium ions, apparently, leaking from a colorant (calcium carbonate) promoted by glacial acetic acid as a modulator used to produce large single crystals of HKUST-1. This finding was confirmed by elemental analysis and a model experiment that resulted in a new calcium-based 1D coordination polymer [Ca(H₂BTC)₂(H₂O)₅]_n under the same solvothermal conditions with no copper or calcium salts put into a 3D-printed autoclave.     

焦炉上升管内壁结焦炭层的光谱学分析及结焦机理研究

以焦炉上升管内壁结焦炭层块为研究对象，采用X射线荧光光谱仪（XRF）、X射线衍射仪（XRD）、傅里叶红外光谱仪（FTIR）和激光共聚焦拉曼光谱仪（Raman）对结焦炭层的元素组成，以及各结焦炭层的矿物组成、组成结构和分子结构进行测试。分析从结焦炭层块外表面向内表面过渡的各结焦炭层的差异性，揭示焦炉上升管内壁结焦机理。结果表明焦炉上升管内粉尘中Fe，S和Cr极易催化荒煤气中蒽、萘等稠环芳烃化合物成炭，在焦炉上升管内壁形成炭颗粒沉积，为焦油凝结挂壁提供载体，在荒煤气温度降至结焦温度时易结焦积碳。结焦炭层均含有芳香层结构，随着结焦炭层从外表面向内表面过渡，各结焦炭层的面层间距(d₀₀₂)逐渐降低、层片直径(L_a)先降低后增加、层片堆砌高度(Lc)和芳香层数(N)先稳定后增加。结焦炭层石墨化过程是由结焦炭层内表面向外表面进行，主要包括其片层外缘的羧基和部分C-O结构的降解剥离，从而形成高度规整的共轭结构。结焦炭层块中C元素是以结晶碳与无定型碳的混合物形式存在。以上研究为解决焦炉上升管内壁结焦及腐蚀问题，提高换热器换热效率，有效回收焦炉荒煤气显热，降低焦化企业能耗提供实验基础和理论依据。     

光束发散度对紫外写入光纤光栅的影响

用傅里叶衍射光学分析了准分子激光束发散度对于光纤光栅制备的影响，发现光束发散角使光纤光栅的布拉格波长发生改变，相位版后干涉场沿光纤轴向和径向不均匀，对制备30dB高反射率光纤光栅造成困难。实验结果与理论分析基本一致，相对于理想平行光束情况，会聚光束使得光纤光栅布拉格波长出现在短波一边，发射光束使得光纤光栅布拉格波长出现在长波一边。     

Real time estimation of CO2 laser weld quality for automotive industry

Laser welding is one of the most precise welding processes in joining sheet metals. In laser welding, performing real time evaluation of the welding quality is very important to enhance the efficiency of the welding process. In this study, the plasma and spatter, which are generated during laser welding, are measured using UV and IR photodiodes. The factors that influence weld quality are classified into five categories; optimal heat input, slightly low heat input, low heat input, partial joining due to gap mismatch, and nozzle deviation. The data number deviated from reference signals and their standard deviations were also considered to evaluate the qualities. A system was also formulated to perform real time evaluations of the weld quality using a fuzzy multi-feature pattern recognition with the measured signals.     

Scattering of Laser Light from Mixed Micelles

Dynamic and static scattering of light was employed to investigate mixed micelles of two homologous anionic surfactants-sodium octyl sulfate and sodium hexadecyl sulfate, above the phase boundary temperature and critical micelle concentrations (cmc). The results indicate that the mixed micelles change from prolate to sphcrical as the molar ratio SOS/SHS increases from 1 to 8. Below 1 or above 8, the formation of micelles is due to one surfactant dissolving the other.     

Spectroscopic characterization of core and shell regions in monolayer protected gold nanoparticles

We report studies on the structure of the metallic core and the alkyl cap layer in monolayer protected gold nanoparticles having sizes down to 1.6 nm. These particles are obtained by laser ablating gold targets in alkane-thiol solutions at different concentrations. The electronic structure of gold core and the vibrational properties of the capping hydrocarbon chains reveal effects connected with the nanosized nature of the particles.     

Focusing and diffraction by an optical lens and a small circular aperture

Based on the vectorial Rayleigh–Sommerfeld diffraction integrals, analytical expressions for the transversal and axial field distribution of plane waves propagating through a thin lens followed by a small circular aperture are derived and used to study the focusing and diffraction properties of plane waves. Some special cases of our general result are discussed, and illustrative numerical calculation results are given. It is found that the vectorial nonparaxial approach should be applied if the aperture dimension is comparable with the wavelength or the focusing is strong.     

Surface structures formed by individual adsorption and coadsorption of Mn and Bi on Cu(0 0 1), studied by LEED

We have studied the individual adsorption of Mn and Bi, and their coadsorption on Cu(0 0 1) by low-energy electron diffraction (LEED). For Mn, we have determined the c(2 × 2) structure formed at 300 K, whose structure had been determined by several methods. We reconfirmed by a tensor LEED analysis that it is a substitutional structure and that a previously reported large corrugation (0.30 Å) between substitutional Mn and remaining surface Cu atoms coincides perfectly with the present value. In the individual adsorption of Bi, we have found a c(4 × 2) structure, which is formed by cooling below ∼250 K a surface prepared by Bi deposition of ∼0.25 ML coverage at 300 K where streaky half-order LEED spots appear. The c(4 × 2) structure has been determined by the tensor LEED analysis at 130 K and it is a substitutional structure. In the coadsorption, we found a c(6 × 4) structure, which has been determined by the tensor LEED analysis. It is very similar to the previously determined structure of the c(6 × 4) formed by coadsorption of Mg and Bi, and embedded MnBi₄ clusters are arranged in the top Cu layer instead of MgBi₄. Large lateral displacements of Bi atoms in the c(6 × 4)-(Mn + Bi) suggest that the Mn atoms undergo the size-enhancement caused by their large magnetic moment.     

用变形全息透镜实现变形分数傅里叶变换

利用一发散点光源和一束倾斜平行光制作出在两个垂直方向上具有不同焦距的变形全息透镜,且用此全息元件实现了变形分数傅里叶变换。变形全息透镜两个方向上的焦距随全息记录条件和再现条件而变化,分析了用这种全息透镜实现变形分数傅里叶变换的条件。实验表明,用该元件能够方便地实现任意级次的变形分数傅里叶变换。