Elongating the area of plasma/fluid interaction of surface nanosecond pulsed discharges

Plasma-assisted flow control is of high industrial interest, but practical applications at full scale require a large surface of interaction. Nanosecond pulsed Dielectric Barrier Discharge (DBD) have demonstrated promising results of flow control, but their interacting region is limited to only a few cm². In this paper, the conditions to extend a surface nanosecond DBD are documented. It is shown that a sliding discharge regime can fully fill an inter-electrode distance of 40 mm. This discharge regime promotes the formation of two hemispheric pressure waves originating from both air-exposed electrodes while an horizontal region of pressure gradient is also observed.     

Scheduling data transfers in a network and the set scheduling problem

In this paper we consider the online ftp problem. The goal is to service a sequence of file transfer requests given bandwidth constraints of the underlying communication network. The main result of the paper is a technique that leads to algorithms that optimize several natural metrics, such as max-stretch, total flow time, max flow time, and total completion time. In particular, we show how to achieve optimum total flow time and optimum max-stretch if we increase the capacity of the underlying network by a logarithmic factor. We show that the resource augmentation is necessary by proving polynomial lower bounds on the max-stretch and total flow time for the case where online and offline algorithms are using same-capacity edges. Moreover, we also give polylogarithmic lower bounds on the resource augmentation factor necessary in order to keep the total flow time and max-stretch within a constant factor of optimum.     

Synthesis and characterization of soluble polyimides containing trifluoromethyl groups in their backbone

A series of polyimides were synthesized from 2,2‐Bis(3,4‐dicarboxyphenyl)hexafluoropropane, 2,2‐bis(3‐amino‐4‐hydroxyphenyl)‐hexafluoropropane, and 4,4′‐oxydianiline by chemical imidization. The effects of the diamine ratios on the properties of the films were evaluated through the study of their thermal, electrical, and morphological properties. All the polymers exhibited better solubility in most of the organic solvents and hence were easily processable. Polyimides with more 2,2‐bis(3‐amino‐4‐hydroxyphenyl)‐hexafluoropropane exhibited better solubility and a low refractive index, which is highly desired for microelectronic applications. The dielectric constant and birefringence were strongly dependent on the fluorine content. With an increase in the fluorine substitution, both the dielectric constant and birefringence decreased. All the polymers exhibited high thermal stability (>400 °C). The absence of crystalline melting in differential scanning calorimetry and broad wide‐angle X‐ray diffraction patterns revealed the amorphous nature of the polymers, which was due to the presence of bulky CF₃ groups and hinged ether linkages of the diamine component. The residual stress values decreased with an increase in the 4,4′‐oxydianiline content, and the results were in agreement with the dielectric constant. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 4303–4312, 2004     

Rheooptical investigation of the crystallization of poly(ethylene terephthalate) under tensile strain

The crystallization of poly(ethylene terephthalate) under uniaxial tensile strain at different extension rates was investigated with optical polarimetry in a temperature range between the glass-transition temperature and the quiescent crystallization temperature. The evolution of the optical properties of the polymer, including the turbidity, birefringence, and dichroism, were monitored simultaneously with the mechanical parameters. To complete the semicrystalline microstructure characterization of the polymer under strain, an online wide-angle X-ray diffraction (WAXD) technique was used in separate experiments, which were performed under the same thermomechanical conditions. For real-time measurements, a high-energy synchrotron radiation source was used. The optical properties provided information about both the crystalline and amorphous phases, whereas the WAXD patterns essentially gave information about the crystalline phase. The two experimental techniques were then used in a complementary way to characterize the semicrystalline microstructure. Significant deviations from the stress-optical rule were found. This was attributed to both transient effects and the appearance of crystallites, which consisted of highly oriented molecular segments that could contribute to the optical anisotropy but not necessarily to the stress. The behavior of the optical dichroism was found to be qualitatively different from that of the birefringence. The latter monotonically increased with the strain, whereas the former first increased with the strain, passed through a maximum, and then decreased to a steady-state value. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1915–1927, 2004     

Chalcogenide based all-solid-state thin electroplated ion-selective membrane for Hg(II) flow-injection determinations

The response to Hg(II) of a thin all-solid-state Te-doped silver chalcogenide membrane, described by the general formula Ag₂ + δSe_{1 − x}Te_x, which has been electrochemically prepared following a previously proposed approach, has been investigated. The kinetics of formation of the membrane's secondary dynamic response to Hg(II) has been successfully combined with the precise timing and transient signal, typical for flow-injection (FI) measurements, in developing a sensitive and reliable mercury FI detector. Under optimized stream conditions it exhibits a linear Nernstian response, with a double slope of the calibration graph of 59 mV dec⁻¹, over the mercury(II) concentration range 10⁻⁶ − 10⁻³ M, the typical sample throughput amounting to about 70 samples per hour. The observed chemical amplification of the signal is due to the specificity of the processes dominating the initial step in formation of the steady-state signal of the membrane to mercury. The analytical performance of the Hg(II) FI detector, as regards sensitivity, reproducibility, selectivity and long-term stability has been thoroughly investigated. The exact procedure for membrane electrodeposition is given and the potential of the proposed approach as a cost-effective way for preparing chalcogenides of unique structure and properties has been outlined in the above context.     

Flow-injection determination of 3-hdroxybutyrate in serum with an immobilized 3-hydroxybutyrate dehydrogenase reactor and chemiluminescence detection

A flow-injection system for the determination of 3-hydroxybutyrate in serum is described. 3-Hydroxybutyrate dehydrogenase is immobilized on poly(vinyl alcohol) beads and incorporated in a flow-injection system. 1-Methoxy-5-methylphenazinium methylsulphate reacts with enzymatically generated NADH to give H₂O₂, which is detected chemiluminometrically with the reaction of luminol and hexacynoferrate(III). Serum is diluted and filtered through an ultrafiltration membrane. The system responds linearly to injected samples (80 μl) in the concentration range 0.5–300 μM; the detection limit is 0.1 μM. The within-day relative standard deviation (n = 90) for 58 μM 3-hydroxybutyrate in serum is 0.8%. The maximum throughout is 20 samples per hour. The immobilized enzyme is stable for at least 1 month.     

Two-dimensional numerical calculation of the flow field about a scoop inlet by the piecewise linear method

The piecewise linear method (PLM) based on time operator splitting is used to solve the unsteady compressible Euler equations describing the two-dimensional flow around and through a straight wall inlet placed stationary in a rapidly rotating supersonic flow. The PLM scheme is formulated as a Lagrangian step followed by an Eulerian remap. The inhomogeneous terms in the Euler equations written in cylindrical coordinates are first removed by Sod's method and the resulting set of equations is further reduced to two sets of one-dimensional Lagrangian equations, using time operator splitting. The numerically generated flow fields are presented for different values of the back pressure imposed at the downstream exit of the inlet nozzle. An oblique shock wave is formed in front of the almost whole portion of the inlet entrance, the incoming streamlines being deflected towards the higher pressure side after passing through the oblique shock wave and then bending down to the lower pressure side. A reverse flow appears inside the inlet nozzle owing to the recovery pressure of the incoming streams being lower than the back pressure of the inlet nozzle.     

光泽精化学发光体系的研究与应用

对光泽精化学发光体系的动力学性质、荧光光谱、化学发光光谱及化学发光机理进行研究和探讨。详细研究了光泽精 - H2 O2 - Co( )流动注射化学发光体系的最佳分析条件。结果表明 ,当光泽精 (L c)为 2 .5×10 - 5mol/L、H2 O2 为 0 .5 mol/L、Na OH为 0 .4 mol/L、CTMAB为 2 .0× 10 - 5mol/L时 ,测定 Co( )的校准曲线线性范围为 0 .0 5— 2 0 0μg/m L ,检出限为 0 .0 1μg/m L。对 10μg/m L Co( )连续测定 7次 ,相对标准偏差为 1.7%。     

Generic Transport Aft-body Drag Reduction using Active Flow Control

Active flow-separation control is an effective and efficient mean for drag reduction and unsteady load alleviation resulting from locally or massively separated flow. Such a situation occurs in configurations where the aerodynamic performance is of secondary importance to functionality. The performance of heavy transport helicopters and aeroplanes, having a large, and almost flat, aft loading ramp suffer from the poor aerodynamics of the aft body. Hence, a combined experimental and numerical investigation was undertaken on a generic transport aeroplane/helicopter configuration. The experimental study provided surface pressures, direct drag measurements, surface and smoke flow visualization. The baseline flow was numerically analyzed, using finite volume solutions of the RANS equations. The baseline flow around the model was insensitive to the Reynolds number in the range it was tested. The flow separating from the aft body was characterized by two main sources of drag and unsteadiness. The first is a separation bubble residing at the lower ramp corner and the second is a pair of vortex systems developing and separating from the sides of the ramp. As the model incidence is decreased, the pair of vortex systems also penetrates deeper towards the centerline of the ramp, decreasing the pressure and increasing the drag. As expected, the ramp lower corner bubble was highly receptive to periodic excitation introduced from four addressable piezo-fluidic actuators situated at the ramp lower corner. Total drag was reduced by 3–11%, depending on the model incidence. There are indications that the flow in the wake of the model is also significantly steadier when the bubble at the lower ramp corner is eliminated. The vortex system is tighter and steadier when the ramp-corner bubble is eliminated.     

Bilevel programming approach applied to the flow shop scheduling problem under fuzziness

This paper presents a fuzzy bilevel programming approach to solve the flow shop scheduling problem. The problem considered here differs from the standard form in that operators are assigned to the machines and imposing a hierarchy of two decision makers with fuzzy processing times. The shop owner considered higher level and assigns the jobs to the machines in order to minimize the flow time while the customer is the lower level and decides on a job schedule in order to minimize the makespan. In this paper, we use the concepts of tolerance membership function at each level to define a fuzzy decision model for generating optimal (satisfactory) solution for bilevel flow shop scheduling problem. A solution algorithm for solving this problem is given. Mathematics Subject Classification: 90C70, 90B36, 90C99