Computing upward topological book embeddings of upward planar digraphs

We describe a unified approach for studying book, point-set, and simultaneous embeddability problems of upward planar digraphs. The approach is based on a linear time strategy to compute an upward planar drawing of an upward planar digraph such that all vertices are collinear. Besides having impact in relevant application domains of graph drawing and computational geometry, the presented results open new research directions in the area of upward planarity with constraints of the positions of the vertices.     

Drawing c-planar biconnected clustered graphs

In a graph, a cluster is a set of vertices, and two clusters are said to be non-intersecting if they are disjoint or one of them is contained in the other. A clustered graph C consists of a graph G and a set of non-intersecting clusters. In this paper, we assume that C has a compound planar drawing and each cluster induces a biconnected subgraph. Then we show that such a clustered graph admits a drawing in the plane such that (i) edges are drawn as straight-line segments with no edge crossing and (ii) the boundary of the biconnected subgraph induced by each cluster is a convex polygon.     

深能级杂质对光导半导体开关非线性特性的影响

建立了非线性GaAs光导开关深能级杂质瞬态模型的基本方程,获得了与实验现象定性吻合的电流输出,给出了平均载流子随时间演化的情况.分析结果表明,在考虑了深能级杂质的俘获、发射和碰撞电离后,有可能对非线性光导开关中发生的一系列现象做出解释,进一步的仔细分析将对非线性光导开关的设计和制作提供理论指导.     

200MW非再热双抽供热机组变工况计算及工况图的绘制

工况图在热电厂的设计和运行中具有广泛的用途。本文根据引进型双抽非再热200MW供热机组的技术特点，通过编程在纯凝汽工况、单抽工业抽汽工况、单抽采暖抽汽工况和双抽供热等典型变工况计算的基础上，完成了当新蒸汽负荷、工业抽汽负荷和采暖抽汽负荷发生改变时的变工况计算，并绘制了该机组的运行工况图．     

非弹性体增韧—聚合物增韧的新途径

本文是一篇关于非弹性增韧方法的综述。文章首先简要回顾了传统的橡胶增韧韧性聚合物材料的机理,然后着重介绍了最近在国外出现的刚性有机填料(ROF)增韧的基本概念、分析方法和增韧的冷拉机理,列举了脆性塑料粒子和韧性基体组成的合金体系的大量实验结果来说明以上内容,最后通过与传统橡胶增韧机理的对比指出非弹性体增韧是不同于后者的一种新增韧方法,并有可能成为制备高强度、高韧性工程塑料的一种新途径。     

Mechanical properties and transition temperatures of crosslinked-oriented gelatin

 This second part of a systematic study of the properties of crosslinked-oriented gelatin involves the effects of orientation and water content on the glass transition temperature T _g and on the melting behavior. The samples were the same as those in the preceding study, and their transition temperatures were determined by both differential scanning calorimetry and dynamic mechanical thermal analysis. The crosslinked gelatin which had been room-conditioned showed two transition temperatures: the lower one was attributed to T _g of the water-plasticized gelatin, and the higher one was interpreted as T _g of dried gelatin superimposed by melting. A rather unusual situation arose because of the fact that the T _g and melting temperatures T _m (217 and 230 ^°C, respectively) are so similar. Using water as plasticizer not only decreases T _g but produces imperfect crystallites which melt below the T _g of the system. The presence of the amorphous phase in the glassy state would presumably make it essentially impossible to define a melting point or crystallization temperature in the normal manner, as an equilibrium between crystalline and amorphous phases. Received: 8 October 1996 Accepted: 2 November 1995     

Influence of drawing and heat treatment on surface free energies of polyethylene terephthalate fibers

The surface free energies of polyethylene terepthalate fibers with different draw ratios were experimentally determined by contact angle measurements inn-alkane/water systems. The dispersive component of the surface free energy increased with increasing draw ratio, whereas the nondispersive one remained almost constant. After heat treatment, the dispersive surface free energy increased, but was reduced above 140°C. The nondispersive component increased by heat treatment at 190°C. The increases in the density and birefringence of the fibres due to the drawing and heat treatment suggested that the increase in the dispersive surface free energy was caused by the increase in the atomic density at the fiber surface due to drawing and heat treatment. ESCA results indicated that the increment in the nondispersive surface free energy due to heat treatment was caused by the addition of functional groups to the fiber surface due to heat treatment.     

Gas chromatographic and mass spectrometric characterization of isomeric alkylthiophenes (C20) and their occurrence in deep sea sediments

Six isomeric C₂₀ alkylthiophenes were synthesized in order to prove the occurrence of such compounds in various deep sea sediments. As expected from the analogy with the corresponding saturated hydrocarbons, 2- and 3-heptadecylthiophene have considerably longer relative retention times than the isomeric isoprenoid compounds, i.e. 2- and 3-(4,8,12-trimethyltridecyl)thiophene and 3- and 4-methyl-2-(3,7,11-trimethyldodecyl)thiophene. Covats retention indices for all compounds were determined by isothermal analysis at 190°C on two different silicone-coated capillary columns. The mass spectra of the monoalkylated thiophenes show a base peak at m/z 98 corresponding to a Mcafferty rearrangement product in the case of the 3-substituted isomers, whereas a simple benzylic cleavage dominates in the mass spectra of 2-alkylthiophenes. 4-Methyl-2-(3,7,11-trimethylodecy)thiophene is an exception from this simple rule because also shows the McLafferty rearrangement as dominant fragmentation. Two of the isoprenoid thiophenes are prominent compounds in various deep sea sediments.     

The preparation of thick-film glass capillary columns

A detailed method for the routine preparation of glass capillary columns is presented. The method consists of coating a glass tube with quartz powder prior to pulling the tube into a capillary. The inner surface of the capillary consists of an even distribution of quartz particles fused to the walls. This surface has been found readily deactivated by standard procedures and ideal for the preparation of thick-film glass capillary columns. The method has been thoroughly tested in two independent laboratories to ensure that the procedures described are reproducible.