基于CSCW的协同编著系统的设计

讨论了计算机支持的协同工作(CSCW)的主要技术，其中重点讨论了协同编著系统设计中的并发控制技术，指出了其与传统的并发控制技术的区别。根据CSCW的基本原理设计出了一个基于Browse／Server结构的协同编著系统的系统模型。该系统模型比传统的模型更加方便了用户之间通过Internet的浏览器进行协作。     

Bounds to optimal burn‐in and optimal work size

Burn‐in is a widely used method to improve the quality of products or systems after they have been produced. In this paper, we consider the problem of determining the optimal burn‐in time and optimal work size maximizing the long‐run average amount of work saved per time unit in the computer applications. Assuming that the underlying lifetime distribution of the computer has an initially decreasing or/and eventually increasing failure rate function, an upper bound for the optimal burn‐in time is derived for each fixed work size and a uniform (with respect to the burn‐in time) upper bound for the optimal work size is also obtained. Furthermore, it is shown that a non‐trivial lower bound for the optimal burn‐in time can be derived if the underlying lifetime distribution has a large initial failure rate. Copyright © 2005 John Wiley & Sons, Ltd.     

Negative luminescence from mid-wave infrared HgCdTe diode arrays

A self-referencing, optical modulation technique was used to measure the negative luminescence efficiencies of an array of mid-wave infrared HgCdTe photodiodes with cutoff wavelength 4.6 μm as a function of sample temperature. The internal efficiency at a wavelength of 4 μm was 93% at 295 K, and nearly independent of temperature in the 240–300 K range. This corresponds to an apparent temperature reduction >50 K at room temperature and >30 K at 240 K. Moreover, the reverse-bias saturation current density was only 0.13 A/cm². The measured transmission and emission spectra were simulated using empirical HgCdTe absorption formulas from the literature.     

路径对摩擦力做功的影响

本文通过讨论两种临界情况下摩擦力所做的功的变化情况，进一步阐明非保守力做的功与路径有关．     

Optimal design of a convergent-barrel cold spray nozzle by numerical method

A convergent-barrel (CB) cold spray nozzle was designed through numerical simulation. It was found that the main factors influencing significantly particle velocity and temperature include the length and diameter of the barrel section, the nature of the accelerating gas and its pressure and temperature, and the particle size. Particles can achieve a relatively low velocity but a high temperature under the same gas pressure using a CB nozzle compared to a convergent-divergent (CD) nozzle. The experiment results with Cu powder using the designed CB nozzle confirmed that particle deposition can be realized under a lower gas pressure with a CB nozzle.     

Reply to “Comment on papers by K. Shanahan that propose to explain anomalous heat generated by cold fusion”, E. Storms, Thermochim. Acta, 2006

Dr. E. Storms has published a Letter [E. Storms, Comment on papers by K. Shanahan that propose to explain anomalous heat generated by cold fusion, Thermochim. Acta, 2006] in which he argues that in a sequence of recent papers, the apparent excess heat signal claimed by Dr. Shanahan to arise from a calibration constant shift is actually true excess heat. In particular he proposes that the mechanisms proposed that foster the proposed calibration constant shifts cannot occur as postulated for several reasons. As well, he proposes Shanahan has ignored the extant data proving this. Because this Letter may lend unwarranted support to acceptance of cold fusion claims, these erroneous arguments used by Storms need to be answered.     

Band bending at the Si(1 1 1)–SiO2 interface induced by low-energy ion bombardment

Experiments employing photoreflectance spectroscopy have uncovered band bending due to electrically active defects at the Si(1 1 1)–SiO₂ interface after sub-keV Ar⁺ ion bombardment. The band bending of about 0.5 eV resembles that for Si(1 0 0)–SiO₂, and both interfaces exhibit two kinetic regimes for the evolution of band bending upon annealing due to defects healing. The healing takes place about an order of magnitude more quickly at the (1 1 1) interface, however, probably because of less fully saturated bonding and higher compressive stress.     

显像管调制特性的测量与分析

测试了显象管调制特性曲线，并分析了特性曲线与显像管工作原理．     

Sn/Ge(1 1 1) α-phase: characterization of image resonances by specular electron reflection and selective electron scattering

Image potential resonances on the Sn/Ge(1 1 1) α-phase are investigated by two closely related methods: specular electron reflection and so-called selective electron scattering. Electrons from image resonances are detected on this surface at 120 and 300 K, i.e. below and above the phase transition at about 200 K. The dispersion of the image resonances reveals at these two temperatures equivalent effective electron masses, which are characteristic for this type of electronic surface states. The results of the two methods are consistent according to the similarity of the scattering processes. Changes in the loss peak intensity with the annealing temperature are assigned to the surface quality and are reflected by characteristic photoemission intensities.     

Synergistic effect between 4-(2-pyridylazo) resorcin and chloride ion on the corrosion of cold rolled steel in 0.5 M sulfuric acid

The corrosion inhibition of 1-(2-pyridylazo)-2-naphthol (PAR) on the corrosion of cold rolled steel in 0.5 M sulfuric acid (H₂SO₄) was studied using weight loss method and potentiodynamic polarization method. Results obtained revealed that together with chloride ion, PAR is an effective corrosion inhibitor for steel corrosion in sulfuric acid. It was found that for steel corrosion inhibition in the presence of single PAR in sulfuric acid the Temkin adsorption isotherm may be used to explain the adsorption phenomenon. For the mixture of PAR and NaCl used as corrosion inhibitor, however, the Langmuir adsorption isotherm can be used to satisfactorily elucidate the adsorption of mixture of PAR and NaCl. Potentiodynamic polarization studies showed that single PAR mainly acts as a cathodic inhibitor for the corrosion of steel in 0.5 M sulfuric acid. The mixture of PAR and chloride ion, however, acts as a mixed type inhibitor that mainly inhibits cathodic reaction of the steel corrosion in sulfuric acid. By means of electrochemical polarization tests, a desorption potential at ca. −370 mV was observed for the adsorption of mixture of PAR and chloride ion, when potential reaches this value, adsorbed inhibitor molecule heavily departs from the steel surface. For the mixture of PAR and chloride ion, thermodynamic parameters such as adsorption heat, adsorption entropy and adsorption free energy were obtained from experimental data of the temperature studies of the inhibition process at four temperatures ranging from 30 to 45 °C, the kinetic data such as apparent activation energies and pre-exponential factors at different concentrations of the inhibitor were calculated, and the effect of the apparent activation energies and pre-exponential factors on the corrosion rates of cold rolled steel was discussed. The most suitable range of inhibitor concentration was discussed. The inhibitive action was satisfactorily explained by using both thermodynamic and kinetic models. Synergism between chloride ion and PAR was proposed. The results obtained from weight loss and potentiodynamic polarization were in good agreement.