Elastic and Thermophysical Properties of Poly(Vinyl Chloride) and Chlorinated Polyethylene Blends

The results of experimental and theoretical investigations of elastic and thermophysical properties of poly(vinyl chloride) (PVC) and chlorinated polyethylene (CPE) blends are presented. Eight types of specimens with different ratios of weight contents of PVC and CPE (PVC/CPE = 100/0, 90/10, 80/20, 60/40, 40/60, 20/80, 10/90, and 0/100) were tested. The effect of blend composition on the elastic constants (tensile and shear modulus) is discussed. The data on the thermal conductivity, thermal diffusivity, and heat capacity of the blends investigated are also presented.     

Thermal conductivity of poly(vinyl chloride)/polycaprolactone blends

Thermal diffusivity, heat capacity, and density of polyvinyl chloride/polycaprolactone (PVC/PCL) blends were measured by the laser flash method, DSC, and pycnometry, respectively. The thermal conductivity of the PVC/PCL blends was determined from the results. The miscibility of the blend and crystallinity of PCL were determined by DSC. The effect of blend structure on thermal conductivity is discussed. The phase compositions of the PVC/PCL blends are of three types depending on PCL content: i.e., up to 33%, from 33 to 70%, and above 70% PCL by weight. Thermal conductivity, thermal diffusivity, and heat capacity of the PVC/PCL blends are strongly affected by the phase composition of the blend, which changes in a complicated way with PCL content. © 1994 John Wiley & Sons, Inc.     

A co‐ordinate system independent streamwise upwind method for fluid flow computation

A new co‐ordinate invariant streamwise upwind formulation for convection dominated flows is developed. The eddy diffusivity/viscosity is added directly to the equations in order to remove the oscillations in the solution. The equations then can be solved by any high‐order scheme and the solution retains the accuracy of the high‐order scheme. The accuracy and reduced lateral thickness growth rate are demonstrated with several numerical examples, including pure convective flows and lid‐driven cavity flow. The lateral spreading due to the numerical diffusion is controlled by the anisotropic tensor. Copyright © 2004 John Wiley & Sons, Ltd.     

二元合金微观偏析的相场法数值模拟

使用耦合溶质场的相场模拟研究了Ni-Cu二元合金枝晶生长过程中固相溶质扩散系数D_s 对枝晶形貌和微观偏析等的影响.计算结果表明，随着D_s的减少，固液界 面前沿溶质扩散层越薄，枝晶生长越有利，枝晶尖端生长的速度越大，侧向分支越发达；D< sub>s越小，固相中溶质成分的波动越强烈，随着D_s的增大，固相中溶质 成分的波动相应减小；溶质微观偏析程度随D_s的增大而减小. 关键词： 相场方法 微观偏析 固相扩散系数 数值模拟     

Influence of boric acid on the electrochemical deposition of Ni

The electrolytic deposition of Ni onto a paraffin-impregnated graphite electrode from supporting chloride electrolyte (0.5 mol dm⁻³ NaCl) adjusted to the required pH using dilute HCl is investigated. The effect of electrolyte composition on the Ni electrodeposition is studied using linear sweep voltammetry in the cathodic region. An elimination voltammetry procedure was applied to evaluate the polarization curves. The aim of this work was to deduce the mechanism of Ni reduction in the chloride bath as well as the influence of boric acid on this. Positively-charged NiCl⁺ ions were found to be the electroactive particles in the Ni reduction mechanism. The strong competition between the NiCl⁺, Cl⁻ and H⁺ ions for active sites at the electrode is discussed. Kinetically-controlled adsorption/desorption processes of various species were also confirmed using elimination voltammetry with a linear scan. The evolution of gaseous hydrogen, catalyzed by the freshly-deposited Ni, accompanies the electrodeposition process. The presence of boric acid at a sufficiently high concentration inhibits the deposition of Ni and, at the same time, improves the morphology and brightness, as well as the adhesion of the deposited Ni. Elimination voltammetry with a linear scan is an efficient way to evaluate current–potential curves that reflect the electrodeposition of one-component Ni coatings. By eliminating selected currents, additional interesting and useful information can be obtained from voltammetric data.     

Measurement and prediction of solubilities and diffusion coefficients of carbon dioxide in starch–water mixtures at elevated pressures

The solubility and diffusion coefficient of carbon dioxide in intermediate‐moisture starch–water mixtures were determined both experimentally and theoretically at elevated pressures up to 16 MPa at 50 °C. A high‐pressure decay sorption system was assembled to measure the equilibrium CO₂ mass uptake by the starch–water system. The experimentally measured solubilities accounted for the estimated swollen volume by Sanchez–Lacombe equation of state (S‐L EOS) were found to increase almost linearly with pressure, yielding 4.0 g CO₂/g starch–water system at 16 MPa. Moreover, CO₂ solubilities above 5 MPa displayed a solubility increase, which was not contributed by the water fraction in the starch–water mixture. The solubilities, however, showed no dependence on the degree of gelatinization (DG) of starch. The diffusion coefficient of CO₂ was found to increase with concentration of dissolved CO₂, which is pressure‐dependent, and decrease with increasing DG in the range of 50–100%. A free‐volume‐based diffusion model proposed by Areerat was employed to predict the CO₂ diffusivity in terms of pressure, temperature, and the concentration of dissolved CO₂. S‐L EOS was once more used to determine the specific free volume of the mixture system. The predicted diffusion coefficients showed to correlate well with the measured values for all starch–water mixtures. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 607–621, 2006     

Synergistic effect between 4-(2-pyridylazo) resorcin and chloride ion on the corrosion of cold rolled steel in 0.5 M sulfuric acid

The corrosion inhibition of 1-(2-pyridylazo)-2-naphthol (PAR) on the corrosion of cold rolled steel in 0.5 M sulfuric acid (H₂SO₄) was studied using weight loss method and potentiodynamic polarization method. Results obtained revealed that together with chloride ion, PAR is an effective corrosion inhibitor for steel corrosion in sulfuric acid. It was found that for steel corrosion inhibition in the presence of single PAR in sulfuric acid the Temkin adsorption isotherm may be used to explain the adsorption phenomenon. For the mixture of PAR and NaCl used as corrosion inhibitor, however, the Langmuir adsorption isotherm can be used to satisfactorily elucidate the adsorption of mixture of PAR and NaCl. Potentiodynamic polarization studies showed that single PAR mainly acts as a cathodic inhibitor for the corrosion of steel in 0.5 M sulfuric acid. The mixture of PAR and chloride ion, however, acts as a mixed type inhibitor that mainly inhibits cathodic reaction of the steel corrosion in sulfuric acid. By means of electrochemical polarization tests, a desorption potential at ca. −370 mV was observed for the adsorption of mixture of PAR and chloride ion, when potential reaches this value, adsorbed inhibitor molecule heavily departs from the steel surface. For the mixture of PAR and chloride ion, thermodynamic parameters such as adsorption heat, adsorption entropy and adsorption free energy were obtained from experimental data of the temperature studies of the inhibition process at four temperatures ranging from 30 to 45 °C, the kinetic data such as apparent activation energies and pre-exponential factors at different concentrations of the inhibitor were calculated, and the effect of the apparent activation energies and pre-exponential factors on the corrosion rates of cold rolled steel was discussed. The most suitable range of inhibitor concentration was discussed. The inhibitive action was satisfactorily explained by using both thermodynamic and kinetic models. Synergism between chloride ion and PAR was proposed. The results obtained from weight loss and potentiodynamic polarization were in good agreement.     

一种模拟沸石分子筛扩散反应的Monte Carlo方法

在考虑了沸石分子筛中吸附、脱附、扩散和反应的特点的基础上，发展了一种模拟沸石分子筛中扩菜反应的ＭｏｎｔｅＣａｒｌｏ方法。用Ｌａｎｇｍｕｉｒ吸附等温式验证了该方法的合理性，并证明了轰击频率λ代表了反应物气相压力，而吸附、脱附几率之比即为吸附平衡常数。同时，通过改变轰击频率λ和反应几率Ｐｔ，得到了吸附等温线和有效因子随Ｔｈｉｅｌｅ模数变化的曲线。     

四氯化锡催化合成癸二酸二丁酯

在五水四氯化锡作用下,用癸二酸和正丁醇合成了癸二酸二丁酯。当癸二酸、正丁醇和四氯化锡的物质的量之比为1∶8∶0.114,回流分水60 min,酯收率达96.2%。并比较了几种Lewis酸合成癸二酸二丁酯的催化活性。     

Serum Chloride Optical Sensors Based on Dynamic Quenching of the Fluorescence of Photo-Immobilized Lucigenin

This article describes the preparation and performance of an optical sensor for continuous measurement of chloride at extracellular (serum) levels (20–200mM). The sensor is based on dynamic quenching of the fluorescence of lucigenin which was photo-immobilized on a hydrogel. Quenching occurs via a collisional mechanism, and the decrease in fluorescence intensity on exposure to 100mM chloride typically is –60%. It allows the determination of chloride in the 1 to 200mM concentration range, with a precision of ±3mM at 120mM. Bromide, iodide and salicylate act as interferents, while the effect of pH and oxygen is negligibly small. The sensor displays strong fluorescence intensity, excellent reproducibility, long-term stability, response times in the order of 2–5min, and is used in a commercial serum and blood chloride analyzer.Received January 21, 2003; accepted April 6, 2003 Published online July 28, 2003