Ultrasound imaging and evaluation of lesion induced by High Intensity Focused Ultrasound

The present study was to investigate the differential imaging method for detecting HIFU (High Intensity Focused Ultrasound)-induced lesions and the estimation of variation of attenuation for lesion evaluation with log spectral difference algorithm. Experiment results of bovine muscle and liver in vitro were acquired. Several algorithms for lesion detection - Absolute Difference (AD), Sum Absolute Differences (SAD) and Sum Squared Differences (SSD) - were analyzed with several window sizes and threshold values. Then three attenuation parameters were compared to evaluate the degree of tissue damage. It was found that variation of the mean attenuation △α was an effective parameter to evaluate lesions.     

乌洛托品法测定钢铁热浸镀锌量

钢铁热浸镀锌量的测定在GB及世界各国标准里均采用三氯化锑法。因其产生SbH_3有毒气体而被甲醛或乌洛托品代替锑剂。ZBH11001-88采用甲醛,GB/T13825-92及ISO1460-1992(E)均采用乌洛托品。本文对乌洛托品方法进行试验并与三氯化锑法、ZBH11001-88法加以研究比较。 1 试验部分 1.1 主要试剂 乌洛托品(六次甲基四胺,分析纯,含甲醛97％以上) 乌洛托品盐酸退镀溶液,称取乌洛托品3.5g溶于盐酸(1+1)1L中。 1.2 测定步骤 将热浸镀锌钢铁试样制备成可测面积的样品,以无水乙醇及乙醚清除表面油污,烘干冷至室温于万分之一天平上称准至毫克。置于盛有乌洛托品退镀溶液的器皿中,保持样品每平方厘米表面上有10ml以上的     

轻型汽车后桥半轴断裂件的组织及断口特征

采用光学显微镜和扫描电子显微镜等手段，对某轻型汽车40Cr后桥半轴断裂件的组织及断口特征进行了分析结果表明：半轴在调质处理时的淬火温度不够高，使其表层和心部组织中存在较多的铁素体相，造成了工件最终的硬度和疲劳强度不足，导致半轴在使用中发生扭转疲劳断裂．     

Deposition of Diamond-Like carbon Films by High-Intensity Pulsed Ion Beam Ablation at Various Substrate Temperatures

Diamond-like carbon (DLC) films have been deposited on to Si substrates at substrate temperatures from 255℃ to 400O℃ by a high-intensity pulsed-ion-beam (HIPIB) ablation deposition technique. The formation of DLC is confirmed by Raman spectroscopy. According to an x-ray photoelectron spectroscopy analysis, the concentration of sp^3 carbon in the films is about 40% when the substrate temperature is below 300℃ C. With increasing substratetemperature from 25℃ to 400℃, the concentration of sp^3 carbon decreases from 43% to 8%. In other words,sp3 carbon is graphitized into sp^2 carbon when the substrate temperature is above 300℃. The results of xray diffraction and atomic force microscopy show that, with increasing the substrate temperature, the surface roughness and the friction coefficient increase, and the microhardness and the residual stress of the films decrease.     

吹气孔直径对RH精炼过程钢液流动和混合特性的影响

针对90t RH精炼装置,以水力学模拟研究了吹气孔直径对真空循环精炼过程中钢液流动和混合特性的影响.模型和原型的相似比为15.模型吹气孔直径分别为0.8 mm和1.2 mm.结果表明,1.2 mm孔径下环流量和主要工艺参数间的关系为Ql Q80.26Du0.69Dd0.80;在给定的吹气量和插入管内径下,增大吹气孔直径并不显著改变精炼过程中钢液流动特征,环流量随吹气孔直径的增大而略有增大,其关系式为Ql=2.40Q 0.23gD0.72u D0.88d d0.13in;相应地,混合时间稍有缩短;0.8和1.2 mm孔径下,τm与搅拌能密度的关系分别为τm ε5和τm ε0.49.     

钢中Si、Mn的电子探针定量分析与标样

采用特制的Fe-Si、Fe-Mn合金系列标样，用电子探针测定了钢或铁基合金中低含量的Si和Mn元素、与用纯元素作标样、经ZAF修正的结果相比较，提高了分析准确度．     

传感法研究固态钢中镧活度

本文采用LaF3单晶固体电解质测量了473～1223K温度范围内钢中镧的活度.两个平行样品的活度值符合很好,并且LaF3单晶的起始工作温度约为880K.     

高分子钯络合物催化的亚胺化合物的加氢反应

制备了一系列以二氧化硅为载体的侧链上含有各种氮配位基团的聚硅氧烷-钯络合物,这些高分子钯络合物能够在常温常压下催化亚胺化合物的加氢反应并表现出不同程度的催化活性.对其中聚-(N,N-二乙酰基)-γ-氨丙基硅氧烷-钯络合物催化的亚苄基苯胺的加氢反应做了比较深入的研究,发现该催化剂在反应中是稳定的并给出唯一的加氢产物,络合物中的N/Pd原子比、反应温度以及不同底物对反应速度的影响也被报道.     

稀土对60CrMnMo热轧辊钢高温低周疲劳性能的影响

研究了稀土元素对６０ＣｒＭｎＭｏ热轧辊用钢高温低周疲劳性能的影响。结果表明，稀土元素能明显提高６０ＣｒＭｎＭｏ钢的高温低周疲劳寿命，使断裂循环数提高１８．５％～２８．８％，细化、变质钢中的夹杂物，使疲劳断口上的疲劳条带间距减少。同时给出稀土元素的合适加入量为０．０５ｗｔ％～０．１０ｗｔ％。