扩宽OMA-Ⅵ同时谱宽的新方法

OMA－Ⅵ存在同时谱宽窄的缺点，本文用一种新方法大幅度地扩宽了它的同时谱宽，且不降低其系统分辨率，应用效果甚佳。     

非晶调制多层膜Nb/Si中的互扩散研究

利用原位Ｘ射线衍射技术得到非晶调制多层膜Ｎｂ／Ｓｉ中的互扩散系数与退火温度的关系，调制周期Ｌ＝３.２ｎｍ的非晶调制多层膜是用粒子溅射方法制备的．温度范围为４２３—５２３Ｋ的有效互扩散系数通过原位测量多层膜的一级调制峰强度与退火温度之间的关系而得到．利用缺陷陷阱延迟扩散机制解释了所得到的扩散系数与退火温度的关系．建立了可以解释较小前置系数的模型 关键词：     

Second-order random wave solutions for interfacial internal waves in N-layer density-stratified fluid

This paper studies the random internal wave equations describing the density interface displacements and the velocity potentials of N-layer stratified fluid contained between two rigid walls at the top and bottom. The density interface displacements and the velocity potentials were solved to the second-order by an expansion approach used by Longuet-Higgins （1963） and Dean （1979） in the study of random surface waves and by Song （2004） in the study of second- order random wave solutions for internal waves in a two-layer fluid. The obtained results indicate that the first-order solutions are a linear superposition of many wave components with different amplitudes, wave numbers and frequencies, and that the amplitudes of first-order wave components with the same wave numbers and frequencies between the adjacent density interfaces are modulated by each other. They also show that the second-order solutions consist of two parts： the first one is the first-order solutions, and the second one is the solutions of the second-order asymptotic equations, which describe the second-order nonlinear modification and the second-order wave-wave interactions not only among the wave components on same density interfaces but also among the wave components between the adjacent density interfaces. Both the first-order and second-order solutions depend on the density and depth of each layer. It is also deduced that the results of the present work include those derived by Song （2004） for second-order random wave solutions for internal waves in a two-layer fluid as a particular case.     

(111)择优取向的Pb(Zr0.52Ti0.48)O3铁电薄膜的制备及研究

选用不同浓度的Pb(Zr_0.52Ti_0.48)O₃溶胶，用Sol-gel法在Pt/Ti/SiO₂/Si基片上沉积一层厚度不同的Pb(Zr_0.52Ti_0.48)O₃ (PZT52)过渡层，经400℃烘烤、550℃退火等程序后，再用Sol-gel法在PZT52过渡层上沉积Pb(Zr_0.52Ti_0.48)O _{关键词： PZT铁电薄膜 择优取向 过渡层 剩余极化强度}     

Growth studies of m-GaN layers on LiAlO2 by MOCVD

This paper reports that the m-plane GaN layer is grown on （200）-plane LiAlO2 substrate by metal-organic chemical wpour deposition （MOCVD） method. Tetragonal-shaped crystallites appear at the smooth surface. Raman measurement illuminates the compressive stress in the layer which is released with increasing the layer＇s thickness. The high transmittance （80%）, sharp band edge and excitonic absorption peak show that the GaN layer has good optical quality. The donor acceptor pair emission peak located at -3.41 eV with full-width at half maximum of 120 meV and no yellow peaks in the photoluminescence spectra partially show that no Li incorporated into GaN layer from the LiAlO2 substrate.     

约束层对激光驱动冲击波压力影响机理的理论研究

针对刚性约束层、柔性约束层以及液体约束层，从激光诱导冲击波阵面状态、汽化物(包括气体和等离子体)扩散以及冲击波的反射进行分析，发现对于脉宽小于冲击波通过汽化物层的时间间隔的短脉冲激光，约束层并不能直接提高冲击波的冲量，而对于脉宽大于冲击波通过汽化层时间间隔的激光，其增强冲击效果是通过约束汽化物的扩散，提高压力幅值和由于冲击波在约束层与工件表面的多次反射而延长对工件的作用时间来实现的.刚性约束层能最大地增加冲击冲量，而柔性约束层和液体约束层的主要优点是其形状可与非平面形工件表面符合. 关键词： 激光 约束层 扩散 反射波     

宽带膜厚实时监控过程中膜层折射率的确定方法

为了准确计算出镀膜过程中每层膜的折射率，介绍了实时监控过程中确定膜层折射率的2种方法：一种是由实测的透射比光谱直接反算出膜层的折射率；另一种是用最小二乘法的优化算法实时拟合折射率。试验结果表明：在线反算适合单点监控，所得折射率误差小于2%。然而在实际镀膜过程中,由于宽带内膜层参数误差较大,一般大于25%。为此，采用最小二乘法拟合，即在整个宽光谱范围内采集每个波长点的信息，所得结果误差很小，一般都在2％～5%之间,有时可达到10%,在很大程度上提高了实际镀膜时膜厚监控的精度。     

一类图的特征多项式与匹配多项式

本文对一类具有对称轴的图A_n(n≥0),得到了它的特征多项式及匹配多项式的精确表达式;同时还得到A_(?)的完美匹配数。