Active long pulse shaping technique of pulsed CO2 laser using multi-pulse discharge control

We describe the pulse forming of pulsed CO₂ laser using multi-pulse superposition technique. Various pulse shapes, high duty cycle pulse forming network (PFN) are constructed by time sequence. This study shows a technology that makes it possible to make various long pulse shapes by activating SCRs of three PFN modules consecutively at a desirable delay time with the aid of a PIC one-chip microprocessor. The power supply for this experiment consists of three PFN modules. Each PFN module uses a capacitor, a pulse forming inductor, a SCR, a high voltage pulse transformer, and a bridge rectifier on each transformer secondary. The PFN modules operate at low voltage by driving the primary of HV pulse transformer. The secondary of the transformer has a full-wave rectifier, which passes the pulse energy to the load in a continuous sequence.We investigated various long pulse shapes as different trigger time intervals of SCRs among three PFN modules. As a result, we could obtain laser beam with various pulse shapes and durations from about 250 to 1000 μs.     

FAST ACCURATE PREDICTION OF BLANK SHAPE IN SHEET METAL FORMING

By using the Finite Element Inverse Approach based on the Hill quadratic anisotrop-ically yield criterion and the quadrilateral element, a fast analyzing software-FASTAMP for the sheet metal forming is developed. The blank shapes of three typical stampings are simulated and compared with numerical results given by the AUTOFORM software and experimental results, respectively. The comparison shows that the FASTAMP can predict blank shape and strain distribution of the stamping more precisely and quickly than those given by the traditional methods and the AUTOFORM.     

晶格失配对异质外延超薄膜生长中成核特性的影响

利用动力学蒙特卡罗方法模拟了异质外延超薄膜生长中的成核过程.研究了薄膜与衬底的晶格失配对超薄膜生长中成核密度、平均核尺寸、标度关系及生长模式的影响.结果发现产生压（张）应变的晶格负（正）失配使生长过程更早（迟）从成核区进入过渡区，失配越大，这一效应越明显.在相同的沉积条件下，负失配导致超薄膜形成较低的成核密度与较大的平均核尺寸，而正失配则相反.成核密度满足标度关系Ns≈(F/D)χ，随着失配度从-0.04增加到0.02，标度系数χ从0.37逐渐减小到0.33，对应超薄膜生长过程从包含二聚体扩散模式转变到无 关键词： 薄膜生长 成核 晶格失配 蒙特卡罗模拟     

磁控溅射ZnO薄膜的成核机制及表面形貌演化动力学研究

利用原子力显微镜分析了ZnO薄膜在具有本征氧化层的Si(100)和Si(111)基片上的表面形貌 随沉积时间的演化. 通过对薄膜生长形貌的动力学标度表征，研究了射频反应磁控溅射条件 下，ZnO薄膜的成核过程及生长动力学行为. 研究发现，ZnO在基片表面的成核过程可分为初 期成核阶段、低速率成核阶段和二次成核阶段. 对于Si(100)基片，三个成核阶段的生长指 数分别为β₁=1.04，β₂=0.25±0.01，β₃=0.74；对 于Si(11 关键词： ZnO薄膜 磁控溅射 生长动力学 成核机制     

On Numerical Solution of Shape Inverse Problems

The new method is proposed for the numerical solution of a class of shape inverse problems. The size and the location of a small opening in the domain of integration of an elliptic equation is identified on the basis of an observation. The observation includes the finite number of shape functionals. The approximation of the shape functionals by using the so-called topological derivatives is used to perform the learning process of an artificial neural network. The results of computations for 2D examples show, that the method allows to determine an approximation of the global solution to the inverse problem, sufficiently closed to the exact solution. The proposed method can be extended to the problems with an opening of general shape and to the identification problems of small inclusions. However, the mathematical theory of the proposed approach still requires futher research. In particular, the proof of global convergence of the method is an open problem.     

Thermal transformations of selected transition metals oxyhydroxides

We investigated the features of the glass transition relaxation of two room temperature ionic liquids using DSC. An important observation was that the heat capacity jump, that is the signature of the glass transition relaxation, shows a particularly strong value in this type of new and promising materials, candidates for a range of applications. This suggests a high degree of molecular mobility in the supercooled liquid state. The study of the influence of the heating rate on the temperature location of the glass transition signal, allowed the determination of the activation energy at the glass transition temperature, and the calculation of the fragility index of these two ionic glass-formers. It was concluded that this kind of materials belong to the class of relatively strong glass-forming systems. This revised version was published online in July 2006 with corrections to the Cover Date.     

A kinetic Monte Carlo method on super-lattices for the study of the defect formation in the growth of close packed structures

A modified Kinetic Lattice Monte Carlo model has been developed to predict growth rate regimes and defect formation in the case of the homo-epitaxial growth of close packed crystalline structures. The model is an improvement over standard Monte Carlo algorithms, which usually retain fixed atom positions and bond partners indicative of perfect crystal lattices. Indeed, we extend the concepts of Monte Carlo growth simulations on super-lattices containing additional sites (defect sites) with respect to those of the reference material. This extension implies a reconsideration of the energetic mapping, which is extensively presented, and allows to describe a complex phenomenology that is out of accessibility of standard stochastic approaches. Results obtained using the Kawasaki and the Bond-Counting rules for the transition probability of the Monte Carlo event are discussed in details. These results demonstrate how the defect types (local or extended), the formation mechanisms and the defect generation regimes can be characterized using our approach.     

Formulation and survey of ALE method in nonlinear solid mechanics

This paper investigates the applicability and accuracy of existing formulation methods in general purpose finite element programs to the finite strain deformation problems. The basic shortcomings in using such programs in these applications are then pointed out and the need for a different type of formulation is discussed. An arbitrary Lagrangian-Eulerian (ALE) method is proposed and a concise survey of ALE formulation is given. A consistent and complete ALE formulation is derived from the virtual work equation transformed to arbitrary computational reference configurations. Differences between the proposed formulations and similar ones in the literature are discussed. The proposed formulation presents a general approach to ALE method. It includes load correction terms and is suitable for rate-dependent and rate-independent material constitutive law. The proposed formulation reduces to both updated Lagrangian and Eulerian formulations as special cases.     

Form of the Spectra of Nucleus Dimensions in First-Order Phase Transitions

We study a generalization of the analytic theory of first-order phase transitions to the cases of arbitrary droplet growth, of nonisothermal processes, and of heterogeneous centers in the system. We show that in all these cases, the spectra of droplet dimensions are similar. The same forms of the spectra are also obtained for the stationary condensation process in a spatially inhomogeneous system.     

Rebuilding of metal components with laser cladding forming

Laser cladding forming (LCF) is a novel powerful tool for the repairing of metal components. Rebuilding of V-grooves on medium carbon steel substrates has been carried out with laser cladding forming technique using stainless steel powder as the cladding material. Microstructure of the deposited layers has been characterized using optical microscopy (OM), scanning electron microscopy (SEM), energy dispersive X-ray microanalysis (EDAX), electron probe microanalysis (EPMA) and X-ray diffraction (XRD). Mechanical properties of the rebuilt V-groove samples have been evaluated by tensile and impacting tests and microhardness measurement. Experimental results show that good fusion bonding between the rebuilt layers and the substrate has been formed, and the microstructure of the cladding layers is mainly composed of fine, dense and defect-free epitaxial columnar dendrites. Due to the effect of grain size refinement, the tensile strength, impacting toughness, elongation and microhardness of the rebuilt samples have been greatly enhanced compared to those of the substrate. Microhardness is also very uniform throughout the rebuilt regions. With the growth of the deposited layers, the microhardness increases gradually. The good ductility of the deposited regions is verified by the SEM fracture analysis.