Radioactive Tracer Study of the Displacement of Iodine Adatoms from Platinized Platinum Electrode by Carbon Monoxide

Radioactive tracer studies confirm the earlier electrochemical results that carbon monoxide can virtually completely displace iodine adatoms. For the first time, it is found that iodine adatoms are not displaced by carbon monoxide when iodide anions are adsorbed in the presence of an upd silver monolayer. The possible reasons for the effect observed are discussed.     

Local adsorption sites and bondlength changes in Ni(1 0 0)/H/CO and Ni(1 0 0)/CO

The local adsorption geometry of CO adsorbed in different states on Ni(1 0 0) and on Ni(1 0 0) precovered with atomic hydrogen has been determined by C 1s (and O 1s) scanned-energy mode photoelectron diffraction, using the photoelectron binding energy changes to characterise the different states. The results confirm previous spectroscopic assignments of local atop and bridge sites both with and without coadsorbed hydrogen. The measured Ni–C bondlengths for the Ni(1 0 0)/CO states show an increase of 0.16 ± 0.04 Å in going from atop to bridge sites, while comparison with similar results for Ni(1 1 1)/CO for threefold coordinated adsorption sites show a further lengthening of the bond by 0.05 ± 0.04 Å. These changes in the Ni–CO chemisorption bondlength with bond order (for approximately constant adsorption energy) are consistent with the standard Pauling rules. However, comparison of CO adsorbed in the atop geometry with and without coadsorbed hydrogen shows that the coadsorption increases the Ni–C bondlength by only 0.06 ± 0.04 Å, despite the decrease in adsorption energy of a factor of 2 or more. This result is also reproduced by density functional theory slab calculations. The results of both the experiments and the density functional theory calculations show that CO adsorption onto the Ni(1 0 0)/H surface is accompanied by significant structural modification; the low desorption energy may then be attributed to the energy cost of this restructuring rather than weak local bonding.     

Au deposits on graphite: On the nature of high temperature desorption peaks in CO thermal desorption spectra

Due to the discovery of Au as a catalyst for low temperature CO oxidation, the adsorption of CO on Au surfaces has attracted a lot of attention recently. On stepped and rough single crystal surfaces as well as on deposited particles two characteristic desorption states above 100 K have been observed via TPD. We have studied Au deposits on graphite in order to elucidate the nature of these desorption peaks in more detail. For this purpose, Au was deposited at 100 K and 300 K on HOPG as a weakly interacting support. In analogy to other supports, we obtain two desorption states (∼140 K and ∼170 K) whose relative intensities depend strongly on the deposition temperature with the high temperature peak being much more pronounced for the 100 K deposits. After annealing to 600 K, both states drastically lose intensity. XP spectra, on the other hand, show virtually no decrease of the Au 4f intensity as would be expected for desorption or significant changes of the particle morphologies. We conclude that both desorption peaks are defect-related and connected with under-coordinated Au atoms that are lost for the most part upon annealing. These sites could be located at the perimeter of dendritic islands or on small, defect-rich particles in addition to larger particles not adsorbing CO at 100 K. Preliminary STM results are in favour of the second interpretation.     

Polymorphism in alternating polyketones studied by x-ray diffraction and calorimetry

Differential scanning calorimetry and high temperature x-ray diffraction were used to study the perfectly alternating copolymer of ethene and carbon monoxide (polyketone; POKC2). It was found that oriented POK-C2 fibers show a crystalline phase transition at a temperature between 110–125°C with a 10% change in crystalline density. At this temperature, the crystal structure reported recently (POK-α) is transformed to a crystal structure that was reported in the past for room temperature imperfectly alternating polyketone. The latter structure will be designated as POK-β. The influence of chain defects on the crystal structure was studied by synthesizing terpolymers (POK-C2/C3), in which small amounts of propylene-CO units are incorporated into the polymer backbone. The resulting terpolymers differ from the copolymer by the presence of methyl groups randomly distributed along the polyketone backbone chain. Evidence is presented that indicates that the methyl groups are built into the crystal lattice as defects. With more than 5 mole-% propene the terpolymer fibers crystallize exclusively in the β-modification. Below this level the α/β ratio (at room temperature) increases with decreasing amounts of propene. Both as-synthesized and as-spun POK-C2 were found to consist of both POK-α and POK-β; the α/β ratio depends on the method of preparation. Because the drawn POK-C2 fibers studied here consist exclusively of POK-α, the process of spinning and drawing leads to the transformation of unoriented β-rich material into oriented POK-α. © 1995 John Wiley & Sons, Inc.     

Nuclear forward scattering vs. conventional Mössbauer studies of atomically tailored Eu-based materials

With the decrease in size of devices, rapid characterization of nano-devices is an inevitable necessity. It is shown that Mössbauer spectroscopy using synchrotron radiation from the advanced photon source provides such a tool of investigation. Results are presented and compared for conventional Mössbauer and Nuclear Forward Scattering for ¹⁵¹Eu-doped magnesium sulfide as an example, especially at low concentrations.     

钯II催化CO/乙烯共聚加压原位红外光谱研究

聚酿以其优良的物理、化学性能及原料（CO乙烯）简单易得的优点，在世界范围内已引起人们的普遍关注．为寻找价廉的催化剂或改良高效或（11）一双磷催化剂以推动聚酮的工业化进程，必须对共聚机理进行深入的研究．S；，n［’，’1、DrentP］等人根据对产品主链和端基的分析首先     

新型稀土芳香羧酸类配合物的合成及其光致和电致发光性质

合成了新型可溶性稀土芳香羧酸类配合物，测定了有机配体的三重态能级，并考察了其光致发光相对强度、荧光寿命，发现该系列稀土配合物具有很高的光致发光效率。利用其优良的溶解性，采用高聚物掺杂、旋涂技术将其制成薄膜应用于电致发光研究中，成功地制备出具有高色纯度的稀土有机电致发光器件。对于ITO／PVK／PVK：Tb(AS)3Phen：PBD／PBD／Al电致发光器件，其最大亮度为32cd．m^-2。