Effect of pressure on the low-temperature reaction of ethylene with N2O4

Calorimetric monitoring of the autoclave reaction N₂O₄ + C₂H₄ at –85 to +10 °C under argon pressure 10–30 bar revealed that the exothermic chemical reaction started at temperatures above –52 °C at 10 bar, whereas an intensive exothermic reaction started at –85 °C and pressure of 30 bar. IR study showed that oligo/polynitroethylene was formed at 30 bar, while carbonyl and hydroxy compound as well as nitrate R–ONO₂ formation occurred upon processing at 10 bar.     

Viscoelastic properties of ultrathin polycarbonate films by liquid dewetting

A liquid dewetting method for the determination of the viscoelastic properties of ultrathin polymer films has been extended to study thickness effects on the properties of ultrathin polycarbonate (PC) films. PC films with film thicknesses ranging from 4 to 299 nm were placed on glycerol at temperatures from below the macroscopic glass transition temperature (T_g) to above it with the dewetting responses being monitored. It is found that the isothermal creep results for films of the same thickness, but dewetted at different temperatures can be superposed into one master curve, which is consistent with the fact of PC being a thermorheologically simple material. Furthermore, the results show that the T_g of PC thin films is thickness dependent, but the dependence is weaker than the results for freely standing films and similar to literature data for PC films supported on rigid substrates. It was also found that the rubbery plateau region for the PC films stiffens dramatically, but still less than what has been observed for freely standing polycarbonate films. The rubbery stiffening is discussed in terms of a recently reported model that relates macroscopic segmental dynamics with the stiffening. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 1559–1566     

Temperature effects on surface activity and application in oxidation of toluene derivatives of CTAB-SDS with KMnO4

The γ_cmc values of CTAB-SDS decrease from 63.67 mN/m at 10‡C to 36.38 mN/m at 90‡C, slightly lower than those of either CTAB or SDS. Correspondingly, the CMC of CTAB-SDS decreases almost by half. The increase of surface activity of CTAB-SDS can be attributed to the relatively weak electrostatic interaction at high temperature, which is supported by the increase of solubility of CTAB-SDS with rise in temperature. Catalytic effect on oxidation of toluene derivatives with potassium permanganate follows the order CTAB-SDS > SDS > CTAB. This is not caused by the dissociative effect of CTAB-SDS with low surface activity at low temperature, as seen from the fact that almost all oxidative products can be retrieved for different toluene derivatives and surfactants by mimicking the conditions of reaction. In the emulsifications of toluene derivatives at 90‡C, the time that turbid water layers of surfactant solutions take to become clear is the same as that of the catalytic effect on oxidation of toluene derivatives. Thus, it can be inferred that surfactants can improve the oxidation yields of toluene derivatives by increasing the contact between two reacting phases.     

环状连续强激光下光学薄膜的瞬温和热畸变

详细研究了非冷却光学薄膜元件在环形激光光束辐照下的瞬态温度分布和随后的热畸变，并且用泰曼干涉仪实际测量了连续波氧碘激光辐照各种非冷却光学元件的热畸变量并与理论计算相比较，分析结果表明理论和实验相一致。     

离心力场作用下多孔介质中强制对流换热的研究

对离心流化床中空气通过多孔物料层的强制对流换热进行了理论和实验研究。获得了气流和物料间强制对流换热的准则关联式。研究结果表明,在气流速度和温度梯度方向一致的条件下,强制对流换热比通常的边界层强制对流换热有所强化,其换热的准则关联式具有 Nu=CRePr的线性形式。从而验证了改变气流方向和热流密度矢量之间夹角可以强化换热的这一强化传热新原理。     

二氧化钒薄膜的低温制备及其性能研究

针对VO₂薄膜在微测辐射热计上的应用，采用射频反应溅射法，在室温下制备氧化钒薄膜；研究了氧分压对薄膜沉积速率、电学性质及成分的影响.通过调节氧分压，先获得成分接近VO₂的非晶化薄膜，再在400℃空气中氧化退火，便可制得高电阻温度系数，低电阻率的VO₂薄膜，电阻温度系数约为-4%/℃，薄膜方块电阻为R_□为100—300kΩ；薄膜在室温下沉积，400℃下退火的制备方法与微机电加工(micro electromechanic 关键词： 二氧化钒 电阻温度系数 氧分压 射频反应溅射法     

理想气体在热力学中的作用

指出热力学理论是普遍的,不依赖于理想气体.理想气体为热力学理论提供了一个简单的实例,为测量热力学温度提供了一种简单的温度计.     

超临界流体触媒作用下石墨-金刚石转变

 研究了超临界流体CO₂在石墨-金刚石转变中的触媒作用。实验中，采用Ag₂O作为流体触媒的先驱材料，在7.7 GPa压力下，Ag₂O在1 200 ℃分解成Ag和O₂，O₂与石墨套管在高温高压下反应形成CO₂超临界流体。研究结果表明，在7.7 GPa和1 500 ℃以上温度条件下，石墨在CO₂流体触媒的作用下可转变为金刚石晶体，在1 500～1 700 ℃温度范围内合成出的金刚石具有完好的八面体形貌，与天然金刚石的生长特征非常相似。