溶胶-凝胶制备技术与新型催化材料Ⅲ.溶胶粒子表面修饰方法制备催化膜

提出用溶胶粒子表面修饰方法，结合溶胶凝胶技术制备无机催化膜．该方法的基本原理是利用合适的金属配合物在胶粒表面的吸附作用，经溶胶凝胶过程，将活性组分结合到无机膜中．实验测定结果表明：（ＮｉＥＤＴＡ）２－，ＶＯ－３，ＭｏＯ２－４，（Ｐｄ（ＮＨ３）４）２＋，ＰｄＣｌ２－４，ＰｔＣｌ２－６和ＲｈＣｌ３－６可用来修饰ＡｌＯＯＨ溶胶．以Ｐｄ／γＡｌ２Ｏ３催化膜的制备为例，经三次溶胶凝胶过程，可制得无裂缺的厚度为９μｍ的Ｐｄ／γＡｌ２Ｏ３催化膜，膜材料的平均孔直径为６ｎｍ，Ｐｄ被均匀地分布在膜的顶层，其平均粒径为２３ｎｍ．     

Influence of transition metal ions on the textural properties of alumina and aluminasilicates

Accelerated phase transformations and chemical reactions of metastable aluminas and kaolinite, doped with Cu^{2 +}, Mn^{3 +}/Mn^{2 +} and Fe^{3 +}/Fe^{2 +} ions, are accompanied with accelerated decrease of surface area and pore volume values. The phenomena in metal ion doped samples are explained by a catalytic mechanism, in terms of the Jahn-Teller effect. This revised version was published online in June 2006 with corrections to the Cover Date.     

NMR investigation of concentrated alumina and silica slurries

The longitudinal relaxation times (T₁) of water in concentrated silica and alumina slurries were measured as a function of solids content. It was shown that the results could be fit very well with a two-phase fast-exchange model between free and surface-bound water. As expected, values of T₁ for bound water were in the order of 20–2000 times lower than that for free water, indicating a higher effective viscosity of the surface-bound water. The strength of the interaction depended on the particular surface, and all of the aluminas examined interacted more strongly with water than the two silicas studied, which themselves differed considerably. The chemical mechanical polishing (CMP) removal rate of tantalum by silica slurries was shown to be directly correlated with the interaction parameters, derived from the NMR relation times rather than with total surface hydroxyl group concentration.     

Microcalorimetric Adsorption of Alumina Oxide Catalysts for Combination of Ethylbenzene dehydrogenation and carbon Dioxide Shift-reaction

Styrene (STY) is now produced industrially in fairly large quantities by the dehydrogenation of ethylbenzene (EB) using promoted iron oxide catalyst with superheated steam.In this case, small amount of carbon dioxide formed as a by-product was known to inhibit the catalytic activity of commercial catalyst. Recently, there have been some reports which carbon dioxide showed positive effects to promote catalytic activities on the reaction over several catalysts.In this study, we attempted to combine the dehydrogenation of EB to STY with the carbon dioxide shift-reaction. The combine reaction (EB + CO2 → STY + H2O + CO) can be considered as one of the ways of using CO2 resources and can yield simultaneously STY and Carbon oxide.Alumina oxide catalysts such as Al2O3, Na2O/Al2O3 and K2O/Al2O3 were prepared by the usual impregnation method with an aqueous solution of NaNO3 and KNO3, and then calcined at 650℃ for 5 h in a stream of air. The reaction condition is 600℃, flow of CO2 38ml/mon and space velocity (EB) 1.28h-1.     

Photoluminescence properties of the composite of porous alumina and poly (2,5-dibutoxy-1,4 phenylenevinylene)

The spin coating method was used to assemble polymer (Poly (2,5-dibutoxy-1,4-phenylenevinylene)) (DBO-PPV) into the pores of porous alumina which was prepared by anodization. Four peaks in the photoluminescence (PL) spectra of the composite, with contributions from the DBO-PPV and porous alumina, were found. It was also found that the light emitting from the porous alumina could excite the photoluminescence of DBO-PPV. The nanometer effect of the porous alumina can lead to a blue shift of 90 nm of the PL peaks of DBO-PPV.     

The coexistence of γ(γ′) and θ alumina observed by STM and LEED on top of oxide layer grown on CoAl(1 0 0)

We report the coexistence of γ(γ′) and θ alumina grown on the CoAl(1 0 0) surface. Both phases were observed after annealing of alumina at 1150 K by means of scanning tunnelling microscopy (STM). The crystal structures of γ(γ′) and θ alumina were indexed based on low energy electron diffraction (LEED) and STM experimental data.     

甲醇与乙醇一步合成异丁醛用CuO-ZnO/Al2O3催化剂

在ＣｕＯ－ＺｎＯ／Ａｌ２Ｏ３催化剂上，甲醇与乙醇在常压和２１０￣３６０℃温度下一步反应合成异丁醛。利用正交设计方法，研究了ＣｕＯ－ＺｎＯ／Ａｌ２Ｏ３体系催化剂组成和制备条件等因素对催化剂催化性能的影响。结果表明，催化剂中ＣｕＯ含量对催化剂的催化活性影响最大，而ＺｎＯ含量则主要影响催化剂对异丁醛的选择性。催化剂制备条件，如沉淀温度、陈化时间等，也不同程度也影响催化剂的催化性能。ＸＲＤ和ＢＥＴ表征结果     

γ-Al2O3对NiB合金的催化及表面性能的影响

集），Dalian（大连）：1994，p.262||8LiuWeicheng（刘伟成），YanJingqing（晏荆青），JiangBingnan（姜炳南）．CuihuaXuebao（催化学报），1990，||11（2）：929HuCW，WangWZXuGY，etal．J．Nat．GasChem，1994,（3）：194||     

Mesoporous electrode material from alumina-stabilized anatase TiO2 for lithium ion batteries

A mesoporous electrode material whose structure is composed of anatase nanocrystals stabilized by alumina is reported. Powder X-ray diffraction shows the anatase phase only, but micro-Raman spectroscopy shows that the materials have a core-shell morphology with grains of bulk anatase covered by a thin rutile layer on the surface. This structure is unique when compared to analogous materials stabilized by zirconia (PNNL-1). Nitrogen adsorption isotherms demonstrate a monotonous increase in surface area and mesopore volume with increasing Al content. Thin film electrodes from these materials were characterized by lithium insertion electrochemistry. Cyclic voltammograms exhibit significant differences in Li accommodation in Al-free and Al-stabilized materials.     

CuO/ZnO/Al2O3合成甲醇催化剂制备方法

ＣｕＯ／ＺｎＯ／Ａｌ２Ｏ３合成甲醇催化剂的制备方法吴晓晖刘金尧刘崇微朱起明（清华大学化学系一碳化工国家重点实验室，北京１０００８４）何菲（天津大学化工系一碳化工国家重点实验室，天津３０００７２）关键词氧化铜，氧化锌，氧化铝，超细粒子，草酸盐胶体...