Numerical study on thermal performance of TiO2, Fe3O4 and NiCr/engine oil in an inclined wavy pip

The essential intention of the existing article is to illustrate the effect of wall properties on flow and thermal behavior, through a sinusoidal inclined wavy pipe. To succeed this phenomena we assume a sinusoidal pipe consist of wavy surface, whose walls traveling down to its borders and located at an inclined position, moreover titanium dioxide (TiO₂), ferrosoferric oxide (Fe₃O₄) and nichrome (80% Ni and 20% Cr) are considered as nano-particles and unused engine oil is assumed as a base fluid. The arising mathematical equations for thermal and flow ratio with wall slip impact are solved by mathematica. Also, evaluate graphically the thermal and flow behavior of nanofluids for multi values of solid volume fractions (η), rigidity parameter (M₁), stiffness parameter (M₂), viscous damping parameter (M₃), Grashof number (G_r), slip parameter (β) and heat generation parameter (H) also discuss the streamlines for different values of solid volume fraction.     

煤直接液化油中混合酚的分离研究

利用分子筛择形特点，对煤直接液化油中的混合酚实施高效分离。本研究选取间甲酚和对甲酚作为分离煤直接液化油馏分段混合酚的模型化合物，采用化学液相沉积法对HZSM-5吸附剂的孔口结构进行改变，分析分子筛硅铝比及颗粒粒径对模型化合物间甲酚和对甲酚吸附分离性能的影响，以获得高性能固相吸附剂，并将其应用于180-190℃馏分段混合酚分离。结果表明，当分子筛硅铝比为25、粒径为3-5 μm时，分子筛的孔口结构调节效果最优；当正硅酸乙酯的最小用量为0.2 mL/g时，固相吸附剂的吸附量为0.03 g/g，对甲酚选择性高于95%。由于外表面沉积物对吸附剂的孔口结构变化，导致对甲酚选择性的提高。进一步采用HZSM-5（1）吸附剂对真实煤直接液化油混合酚的分离中发现，苯酚和对甲酚的选择性均达到100%。     

Morphologically controlled synthesis of 1-dimensional selenium dioxide and study of its application as catalyst for diesel fuel additive

In this research work, selenium dioxide (SeO₂) nanorods have been prepared by a solvothermal method in which a strong reducing agent (NaBH₄) was used to reduce precursor salt into SeO₂ nanorods. X-ray diffraction (XRD) technique was applied to observe the crystal structure which confirmed its tetragonal geometry. Moreover, morphology and particle size were studied by scanning electron microscopy (SEM). SEM fully described the 1-dimensional morphology of SeO₂ nanorods which then arranged themselves to create a 3-dimensional flower-like structure with an average particle size of 50 nm. Also, the catalytic activity of SeO₂ nanorods as diesel-additive was studied by defining different parameters such as fire and flash points, calorific value, cloud and pour points, specific gravity, and kinematic viscosity. Subsequently, SeO₂ nanorods proved to be an excellent diesel additive due to higher total heat content and lower value of kinematic viscosity which enhances the better performance of the diesel engine.     

Correlation between the Mechanical Properties and the Amount of Desorbed Water for Composites Based on Low-Density Polyethylene and Linen Yarn Production Waste

The effect of the amount of desorbed water on the mechanical properties of composites based on low-density polyethylene and linen yarn production waste (LW) is analyzed by statistical methods. It is shown that the amount of absorbed water decreases during the desorption process at room temperature both for specimens modified and unmodified with diphenylmethane diisocyanate (DIC.) The most sensitive to the action of water is the elastic modulus, which decreases considerably under the effect of water and is fully restored in the desorption process. The tensile strain also increases with the amount of absorbed water. It is found that the elastic modulus of the unmodified composite correlates linearly with the amount of desorbed water. Between the amount of desorbed water and the tensile strain, as well the specific work of deformation, a negative linear correlation is revealed. After water desorption, all strength and deformation characteristics of both the modified and unmodified composites are fully recovered.__________Translated from Mekhanika Kompozitnykh Materialov, Vol. 41, No. 4, pp. 515–524, July–August, 2005.     

Adsorption Behaviour of 134Cs and 22Na Ions on Tin and Titanium Ferrocyanides

Tin and titanium ferrocyanides were studied as adsorbents for alkali metal ions, viz., ¹³⁴Cs and ²²Na, which represent radioactive wastes. The ferrocyanides were prepared in granular form. The tin version contained 11.2% water, while the titanium version contained 17.7% water. The exchange capacities for Cs⁺ and Na⁺ in the hydrated tin version were about 1.5 and 0.7 meq/g, respectively, while those in the titanium version were 2.2 and 1.2 meq/g, respectively. Drying at 250°C decimated those capacities. The diffusional time constant of Cs⁺ at 25°C, determined via Fick's second law, was of order of magnitude 1 × 10^–3 s^–1, though there were minor differences due to particle size and the form of ferrocyanide. Similarly, the effective diffusivity was of order of magnitude 1 × 10^–8 cm²/s. The titanium version responded slightly faster than the tin version. Likewise, equilibrium measurements in mixtures with sodium nitrate, potassium nitrate, or uranium oxide, showed that the titanium version exhibited significantly greater selectivity for Cs⁺ than did the tin version. Unfortunately, tests of complete elution of the Cs⁺ from the ferrocyanides were mostly disappointing. Work continues on that subject.     

Synthesis of Cationic PEM Emulsion and Application in Waste Water Treatment

Cationic polymer as a kind of flocculant is widely applied in purification treatment of waste water. Because it has positive charge group, it is able to connect strongly the suspended matters, short cellulose and other microparticles. The research on synthesis of cationic polymer and application in treatment of waste water is very universal abroad. But domestic research on those is not general. The technology of synthesis of PEM is simple, and the production cost is low. It is easy to apply in treatment of waste water.Synthesis of PEM Emulsion FlocculantSome distilled water, PVA(poly(vinyl alcohol)), EA(ethyl acrylate), and K2S2O8(potassium persulfate) were put into reaction vessel. Kept stirring up under nitrogen. When heated the solution to 40℃, dropped the water solution of MTA[(2-methacryloxylethyl)trimethyl ammonium].Maintained the temperature at 70℃, reacted about 7-8 hours. Then got the PEM emulsion. Changed the ratio of EA and MTA. Obtained a series of PEM emulsions.Stability and Convertibility of PEM EmulsionThe test results showed that when the EA/MTA was 85/15, the PEM emulsion was most stable.When the total monomer quantity was 35%, the convertibility of PEM emulsion was the highest,i.e.98.6%.The MTA Copolymerization Ratio and Morphology of PEM EmulsionWhen the monomers EA/MTA=85/15 and total monomer quantity was 35%, the MTA copolymerization ratio of PEM emulsion was 95.15%(the highest), and the PEM emulsion was some microspheres with 100-180nm of diameter.The Test Results of PEM Emulsion in Treatment of Waste Water The PEM emulsion flocculant was applied in treatment of waste water of paper mill, and measured the precipitation time(t) and transmittancy(T). The test results were showed in table 1. The optimum value of PEM which was able to make the waste water of paper mill into clear water was 0.008%.     

放射性废物概述

全世界许多国家都在着手于核废物的管理任务．目前，还不能认为这个极其困难的问题在任何国家中真正得到了解答，然而又必须得出解答．本文中概括地说明了有关核废物各方面的常识     

新疆野生黑加仑与马林果实的营养成分分析

通过对新疆野生黑加仑和野生马林的脂肪油，8种微量元素，17种氨基酸以及维生素C的含量进行测定得出：黑加仑脂肪油含量为17．9％，马林的脂肪油含量为22．3％，其中，黑加仑脂肪油中，r－亚麻酸的含量为19．02％，而马林中，其含量为9．40％，黑加仑中K，Na,Ca,Cu,Zn,Fe的含量比马林中的含量高，而Mn,Mg元素的含量却比马林含量低；马林的维生素C含量为16．22mg/g，黑加仑的含量为108mg/g，黑加仑的氨基酸的总量为1．63％，马林为1．14％。     

Feasibility study for the preparation of certified reference materials part I – mineral oil contaminated soils

The international joint project HYCREF (Contract No. G6RD-CT-2002-00854), funded by the European Commission in the 5th Framework programme, aimed to develop methods to prepare homogeneous and stable reference materials of water, soil, and waste contaminated with mineral oil hydrocarbons and to certify the mineral oil content by gas chromatographic methods. The results of a feasibility study for the preparation of three soil reference materials are discussed in this paper, and for the preparation of three waste reference materials in the second part (Koch et al., Accred Qual Assur submitted for publication). The soil materials were selected to represent different soil types and contamination levels. The project plan set three requirements for these reference materials: uncertainty in the mineral oil content resulting from the certification exercise <5%, a sample inhomogeneity of <3% and a minimum long-term stability of 5 years. For the most part, these requirements were met within this project.