Determination of ultra-trace gold in natural water by graphite furnace atomic absorption spectrophotometry after in situ enrichment with thiol cotton fiber

A simple method of determining ultra-trace Au in natural water was presented by using graphite furnace atomic absorption spectrophotometry (GFAAS) after in situ enrichment with thiol cotton fiber (TCF). The sample solution was adjusted to pH 1.5-2.0 with HCl, then the water sample was passed through a column packed with 0.10-0.20 g TCF and the flow rate was controlled at 20-40 ml min⁻¹. The effects of interferences, such as complexing and oxidizing agents and other elements adsorbed on TCF were overcome by chemical treatments prior to the desorption of Au. The adsorbed Au was adsorbed with 2.0 ml hot acid, then it was extracted with 1.00 ml methyl isobutylketone (MIBK). For a 5 l water sample, the detection limit of Au is 0.02 ng l⁻¹. The relative standard deviation (R.S.D.) for the determination of 1.44 ng l⁻¹ Au was 9.4%.The method was applied to determine ultra-trace Au both in suspended phase and soluble phase in natural water, the concentrations of total Au in natural water samples range from 0.51 to 67.82 ng l⁻¹. The recovery of added 0.50-6.00 ng l⁻¹ Au was 80-95%. The method is useful in prospecting for Au deposits by means of hydrogeochemical methods. The enrichment is carried out in the field, and then the determination of Au is completed later in the laboratory.     

Radical copolymerization of 2‐trifluoromethylacrylic monomers. II. Kinetics,monomer reactivities,and penultimate effect in their copolymerization with norbornenes and vinyl ethers

Radical copolymerizations of electron‐deficient 2‐trifluoromethylacrylic (TFMA) monomers, such as 2‐trifluoromethylacrylic acid and t‐butyl 2‐trifluoromethylacrylate (TBTFMA), with electron‐rich norbornene derivatives and vinyl ethers with 2,2′‐azobisisobutyronitrile as the initiator were investigated in detail through the analysis of the kinetics in situ with ¹H NMR and through the determination of the monomer reactivity ratios. The norbornene derivatives used in this study included bicyclo[2.2.1]hept‐2‐ene (norbornene) and 5‐(2‐trifluoromethyl‐1,1,1‐trifluoro‐2‐hydroxylpropyl)‐2‐norbornene. The vinyl ether monomers were ethyl vinyl ether, t‐butyl vinyl ether, and 3,4‐dihydro‐2‐H‐pyran. Vinylene carbonate was found to copolymerize with TBTFMA. Although none of the monomers underwent radical homopolymerization under normal conditions, they copolymerized readily, producing a copolymer containing 60–70 mol % TFMA. The copolymerization of the TFMA monomer with norbornenes and vinyl ethers deviated from the terminal model and could be described by the penultimate model. The copolymers of TFMA reported in this article were evaluated as chemical amplification resist polymers for the emerging field of 157‐nm lithography. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 1478–1505, 2004     

Influence of preparation methods on structure and properties of PA6/PA66 blends: A comparison of melt‐mixing and in situ blending

The blends composed of polyamide 6 (PA6) and polyamide 66 (PA66) were obtained using two different preparation methods, one of which was the melt‐mixing through a twin‐screw extruder and the subsequent injection molding; and the other, the in situ blending through anionic polymerization of ε‐caprolactam in the presence of PA66. For the former, there existed a remarkable improvement in toughness but a drastic drop in strength and modulus; however, for the latter, a reverse but less significant trend of mechanical properties change appeared. Various characterizations were conducted, including the analyses of crystalline morphology, crystallographic form, and crystallization and melting behaviors using polarized optical microscopy (POM), wide‐angle X‐ray diffraction (WAXD), and differential scanning calorimetry (DSC), respectively; observation of morphology of fractured surface with scanning electron microscope (SEM); measurement of glass transition through dynamic mechanical analysis (DMA); and the intermolecular interaction as well as the interchange reaction between the two components by Fourier transform infrared spectrometry (FT‐IR) and ¹³C solution NMR. The presence and absence of interchange reaction was verified for the in situ and melt‐mixed blends, respectively. It is believed that the transreaction resulted in a drop in glass transition temperature (T_g) for the in situ blends, contrary to an increase of T_g with increasing PA66 content for the melt‐mixed ones. And the two kinds of fabrication methods led to significant differences in the crystallographic form, spherulite size and crystalline content and perfection as well. Accordingly, it is attempted to explain the reasons for the opposite trends of changes in the mechanical properties for these two blends. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 1176–1186, 2007     

钯II催化CO/乙烯共聚加压原位红外光谱研究

聚酿以其优良的物理、化学性能及原料（CO乙烯）简单易得的优点，在世界范围内已引起人们的普遍关注．为寻找价廉的催化剂或改良高效或（11）一双磷催化剂以推动聚酮的工业化进程，必须对共聚机理进行深入的研究．S；，n［’，’1、DrentP］等人根据对产品主链和端基的分析首先     

Synthesis and Structure of a Dinuclear Copper（Ⅱ）- ditetrazolate Involving in situ Ligand Synthesis

The hydrothermal reaction of 1,2-dicyanobenzene with NaN3 in the presence of CuCl2, 2,2′-bipyridine and H2O affords a novel dinuclear copper(II)-ditetrazolate, [Cu(bpy)- (pdtz)]2 (Hpdtz = 5,5′-1,2-phenylene-ditetrazole, bpy = 2,2′-bipyridine). The pdtz ligand is generated in situ through Sharpless 2 3 cycloaddition reaction. Its crystal structure was deter- mined by single-crystal X-ray diffraction method. The crystal crystallizes in the monoclinic system, space group P21/n with a = 8.2096(16), b = 18.580(4), c = 11.838(2) , β = 103.12(3)o, V = 1758.5(6) 3, Z = 2, Mr = 863.83, Dc = 1.631 g/cm3, F(000) = 876 and μ = 1.272 mm-1. In this novel dinuclear structure, the pdtz ligand adopts a peculiar μ2-η1,η2 coordination mode.     

在位分散聚合聚甲基丙烯酸甲酯/二氧化硅纳米复合材料研究

应用在位分散聚合方法制备了分散相粒径介于１３０ｎｍ左右的聚甲基丙烯酸甲酯／二氧化硅ＰＭＭＡ／ＳｉＯ２纳米复合材料，并利用ＳＥＭ，ＤＭＡ，ＴＧＡ等手段研究了该体系的性能．结果表明，经表面处理的ＳｉＯ２无机填料在复合材料基体中分散均匀，界面粘结好．ＳｉＯ２填充粒子的用量对基体的热稳定性，动态力学行为，光学行为以及拉伸强度，弹性模量，断裂伸长率等力学性能都有较大影响     

Preparation of flame retardant polyamide 6 composite with melamine cyanurate nanoparticles in situ formed in extrusion process

This paper is focused on in situ preparation of melamine cyanurate (MCA) nanoparticles from reaction of melamine (MEL) and cyanuric acid (CA) and their flame retardant polyamide 6 (PA6) composite in the extrusion process through a novel reactive processing method. Fourier transform infrared (FT-IR), X-ray diffraction (XRD), differential scanning calorimetry (DSC), thermogravimetric analysis (TGA) and scanning electron microscopy (SEM) were utilized to characterize the in situ formed MCA nanoparticles and their blends with PA6. Introduction of pentaerythritol (LTP) and water-bound plasticizer dioctyl phthalate (DPT) into the extrusion reaction system greatly inhibits the evaporation of water required for melamine and cyanuric acid reaction at high temperature (higher than 180 °C), laying a foundation for successful in situ preparation of MCA through reactive processing. XRD and FT-IR measurements indicate that under the effect of pentaerythritol, dioctyl phthalate and water, melamine really reacts with cyanuric acid to in situ form MCA in extrusion process. The reaction degree is close to 100%. A very important finding through SEM is that the in situ formed MCA particles, which were found to have aspect ratio of about 7.5, radial size in the range of 70-300 nm (mostly 70-90 nm) and crystallite size of less than 22 nm, are uniformly dispersed in the matrix PA6 at nanoscale. The in situ formed MCA nanoparticles greatly improve the flame retardancy and the mechanical properties of flame-retarded PA6 materials, and the introduced plasticizer dioctyl phthalate also ameliorates the related impact property. The obtained flame-retarded PA6 materials have good comprehensive performance with flame retardancy UL-94 V-0 rating at 1.6 and 3.2 mm thickness, tensile strength 48.0 MPa, elongation at break 106.3% and Izod notched impact strength 8.92 kJ/m². Compared with flame-retarded PA6 material with in situ formed MCA, the one prepared through conventional blending of PA6 with commercial MCA product has improved tensile strength but deteriorated impact strength and flame retardancy.     

Structure of thiocyanate adlayers on Rh(111): an in situ STM study

In situ scanning tunneling microscopy (STM) was used to examine the structure of thiocyanate adlayers specifically adsorbed on Rh(111) in solutions of potassium hydroxide and perchloric acid, both containing potassium thiocyanate (KSCN). An atomically flat terrace-step structure was consistently observed on Rh(111) surfaces prepared by the flame-annealing-quenching method. The Rh(111)-(1 × 1) atomic structure was discerned on the atomically flat terrace even in the alkaline solution. High-resolution STM images disclosed two different structures of the SCN⁻ adlayers, () and (2 × 2), in the alkaline and the acidic media, respectively. In each structure, an individual adsorbed SCN⁻ ion appeared as a single spot with a constant corrugation height in STM images, suggesting that SCN⁻ ions adsorbed predominantly with their S-ends at particular bonding sites on Rh(111). The difference in the adlayer structure in the two solutions can be attributed to the interaction between adsorbed SCN⁻ and coadsorbed K⁺ in the alkaline solution, and is different from that between adsorbed SCN⁻ and H⁺ in the acidic solution. Received: 26 February 1997 / Accepted: 3 March 1997     

PHEMA hydrogels obtained by a novel low-heat curing procedure with a potential for in situ preparation

In this work, we report on poly(2-hydroxyethyl methacrylate) (PHEMA) hydrogels obtained by a low heat curing reaction. These materials are suitable for in situ preparation and therefore endowed with a potential for several biomedical applications. The novel procedure adopted involves as the first step the synthesis of a soluble oligomeric PHEMA precursor containing polymerizable functions as side substituents. As the second step, the precursor is dissolved in equal amounts of 2-hydroxyethyl methacrylate (HEMA) and water, to form a viscous but still injectable syrup. A low temperature water soluble initiator is then added. The curing reaction starts promptly and is completed within few minutes. During the entire process the internal temperature never rises above 40 degrees C. Preliminary mechanical characterizations performed on the hydrogels in their water-swollen state and diffusion tests in absorption/desorption experiments clearly indicated that on all respects the novel hydrogels are comparable with conventional PHEMA hydrogels obtained according to literature from HEMA in the presence of divinyl crosslinkers. However, the much shorter curing time combined with the far lower curing temperature endow the new hydrogels with a higher potential in view of specific surgical requirements, and particularly for in situ preparation.     

现场表面拉曼光谱研究Fe-Mo合金诱导共沉积

现场表面拉曼光谱结果显示，在0．2mol·L-1Na2MoO4,pH＝4．0的溶液中，电位正于0．5V（vsSCE）时只观察到多钼酸盐的拉曼峰（940、880和450cm-1）．负于-0．5V时，出现中心位于730cm-1的宽峰．同时电极表面有蓝色膜生成．表明混合氧化态（MO（Ⅳ），MO（Ⅴ））氧化膜的形成．730cm-1的峰在-1．9V时仍然存在，说明氧化膜没有被进一步还原．在钼酸钠溶液中同时含有0．1mol·L-1FeSO4和0．2mol·L-1柠檬酸时，中间态氧化膜的拉曼峰的中心移到740cm-1．且峰强度随着电位从-1．3V负移到-1．9V而逐渐减弱并最终消失．电极表面沉积层呈银白色，说明由于Fe2 的存在，钼的中间态氧化膜的结构发生了变化，能够被进一步还原形成Fe－Mo合金，表现出诱导共沉积的特征．