A New Kind of Void Soap-free P（MMA-EA-MAA） Latex Particles

Soap-flee P(MMA-EA-MAA) particles with narrow size distribution were synthesized by seeded emulsion polymerization of methyl methacrylate (MMA), ethyl acrylate (EA) and methacrylic acid (MAA), and large voids inside the particles were generated by alkali posttreatment in the presence of 2-butanone. Results indicated that the size of void and theparticle volume were related with the amount of 2-butanone. The generation mechanism of voids was proposed.     

Piezoelectric property improvement of polyethylene ferroelectrets using postprocessing thermal‐pressure treatment

In this work, biaxially stretched polymer foams with well‐defined cellular structures were prepared from polyethylene via blown‐film extrusion and subjected to corona charging to produce a piezoelectric response. The charging parameters were first optimized in terms of charging voltage and needle distance, as well as the gas type and pressure to investigate their effect on the piezoelectric coefficient (d₃₃). The results show that samples charged under nitrogen (N₂) at 100 kPa had better d₃₃ coefficient than those charged under ambient air or N₂ at 20 kPa. Moreover, 2 different thermal pressure treatments were imposed to obtain an optimized eye‐like cellular structure with different cell aspect ratios (AR). The results showed that when the cells were elongated in both the longitudinal and transverse directions (higher AR), higher d₃₃ coefficients were achieved. From all the samples produced, the best results were obtained for a longitudinal aspect ratio (AR‐L) of 7.1, a transversal aspect ratio (AR‐T) of 4.6, and a relative foam density of 0.52 leading to a d₃₃ coefficient of 935 pC/N. This coefficient was further increased using reverse charging and multilayered films, reaching a maximum of 2550 pC/N. This value is much higher than typical ones reported so far for any polyethylene and polypropylene ferroelectrets. These results could increase the use of polyethylene in piezoelectric applications as these materials are very attractive for the large‐scale production of electret‐based sensors and transducers due to their low cost and easy processing.     

An investigation of post treatment on properties and structure of ultrahigh molecular weight polyethylene parts prepared by selective laser sintering for biomedical application

Combined with customization advantage of selective laser sintering (SLS) and excellent performance of ultrahigh molecular weight polyethylene (UHMWPE), it is possible to meet the requirements of artificial joints for biomedical application. However, high viscosity of UHMWPE melt limits the strength of UHMWPE sintered parts. Inspired from metal and ceramic materials, this work aims to improve the performance of UHMWPE parts prepared by SLS using post treatment methods, including heat treatment and hot isostatic pressure (HIP) treatment. Consequently, HIP treatment shows superiority on promoting the performance of UHMWPE sintered parts compared with heat treatment. With the condition of temperature and isostatic pressure, a novel definition of “bonding neck” is given to explain the enhancement of cohesion between each UHMWPE particle in different post treatment. Without any fortifier, the biological safety of artificial joints manufactured by SLS is further guaranteed. Under the isostatic pressure of 12 MPa and temperature of 185°C in HIP treatment, the mechanical strength, tribological performance and other properties are improved dramatically. The tensile strength of the specimen is up to 8.0 MPa, the elongation at break is 99.3%, the impact strength is 8.8 MPa, the friction coefficient is 0.11, the wear rate is 9.3 × 10^?4 mm³/Nm and samples do not show cytotoxicity at the same time.     

Influence of oxygen-plasma posttreatment on the properties of SiO2 films prepared by the electron-beam evaporation method

SiO₂ films were deposited on K9 substrate by the electron-beam evaporation method. The influence of oxygen-plasma posttreatment on the properties of SiO₂ films was investigated. After oxygen-plasma treatment, it was found that the microdefect density of films reduced. We deduced that the absorption of films also reduced. The treated sample exhibited higher LIDT value compared with the as-deposited sample. However, this study is the preliminary work and optimization by this method will be discussed in our future work.     

P(MMA-EA-AA)共聚物组成对无皂乳胶粒碱处理后结构形态的影响——异型结构粒子的形成

采用批量法无皂乳液聚合技术合成了粒径窄分布的甲基丙烯酸甲酯(MMA) - 丙烯酸乙酯(EA)- 丙烯酸(AA)三元共聚物胶乳,并通过碱后处理,制备出了具有异型结构的乳胶粒,探讨了AA用量及MMA /EA质量比对胶粒结构形态的影响.结果表明,当AA含量大于0 .0 4mol时,胶乳中开始出现异型结构粒子,随着AA用量的增加和MMA/EA质量比的减小,异型粒子在胶乳中所占比例增加,胶粒体积先增大后减小.当EA用量较高时,粒子边界模糊,异型结构不明显.     

EIS investigation of a Ce-based posttreatment step on the corrosion behaviour of Alclad AA2024 anodized in TSA

In the aircraft industry, anodizing and posttreatment steps use Cr (VI) compounds, which, despite offering good corrosion resistance and self-healing properties, are highly toxic and carcinogenic. Ce compounds are recognized as efficient corrosion inhibitors for Al alloys, and several works report self-healing ability for these chemicals. In this investigation, the corrosion resistance of Alclad AA2024-T3 alloy anodized in tartaric-sulphuric acid (TSA) bath and posttreated in a solution comprising cerium nitrate without and with hydrogen peroxide was evaluated. The purpose is to investigate the potentiality of using hydrothermal treatment in Ce nitrate solution as candidate to replace Cr (VI) posttreatment. The aim is to provide a posttreatment step which, while improving the corrosion resistance, does not plug the mouths of the pores maintaining the adhesion properties of the porous anodic layer. Microstructural characterization was carried out by SEM-EDS whereas corrosion resistance was evaluated by EIS. The surface analysis showed that the posttreatments, all performed at 50°C, kept the open structure of the pores. EIS analysis showed that the posttreatments performed in the H₂O₂ solution for short immersion times were the most effective in improving the corrosion resistance of the samples, whereas electrical equivalent circuit (EEC) fitting of the data indicated sealing of the porous layer during the immersion of the different samples in the test solution. SEM-EDS analysis of the samples posttreated in the H₂O₂ containing solution, prior and after the corrosion test, showed the presence of Ce oxy-hydroxide randomly deposited on the sample surface, indicating that Ce could be incorporated/stored in the anodic layer.