Developing Flexible Quinacridone-Derivatives-Based Photothermal Evaporaters for Solar Steam and Thermoelectric Power Generation

Solar-driven interfacial vaporization by localizing solar-thermal energy conversion to the air−water interface has attracted tremendous attention. In the process of converting solar energy into heat energy, photothermal materials play an essential role. Herein, a flexible solar-thermal material di-cyan substituted 5,12-dibutylquinacridone (DCN−4CQA)@Paper was developed by coating photothermal quinacridone derivatives on the cellulose paper. The DCN−4CQA@Paper combines desired chemical and physical properties, broadband light-absorbing, and shape-conforming abilities that render efficient photothermic vaporization. Notably, synergetic coupling of solar-steam and solar-electricity technologies by integrating DCN−4CQA@Paper and the thermoelectric devices is realized without trade-offs, highlighting the practical consideration toward more impactful solar heat exploitation. Such solar distillation and low-grade heat-to-electricity generation functions can provide potential opportunities for fresh water and electricity supply in off-grid or remote areas.     

Highly Luminescent Red Phosphorescent OLED with Interfacial Layers for Hole Transport and Electron Injection

Four kinds of red phosphorescent organic light-emitting devices were fabricated and compared to investigate the effect of interfacial layers for hole transport and electron injection. 1 nm-thick LiF in the device A and C and 1 nm-thick Cs₂CO₃ in the device B and D were deposited as an electron injection layer between the anode and the electron transport layer, and 5 nm-thick layer of dipyrazion[2,3-f:2′,2′-h]quinoxaline-2,3,6,7,10,11-hexacarbonitrile[HATCN] was inserted as a hole transport interfacial layer between the hole injection layer and the hole transport layer only in the device C and D. Under a luminance of 1000 cd/m², the power efficiencies were 7.6 lm/W and 8.5 lm/W in the device A and B, and 8.6 lm/W and 13.4 lm/W in the device C and D. The quantum efficiency of the device D was 15.8% under 1000 cd/m² which was somewhat lower than those of the device A and C, but a little higher than that of the device B. The luminance of the device D was much higher than those of the other devices at a given votage. The luminance of the device D at 7 V was 23,710 cd/m², which was 13.0, 3.4, and 4.0 times higher than those of the device A, B, and C at the same voltage, respectively.     

Synthesis,Electronic Properties and WOLED Devices of Planar Phosphorus‐Containing Polycyclic Aromatic Hydrocarbons

We describe the synthesis and the physical properties of polyaromatic hydrocarbons (PAHs) containing a phosphorus atom at the edge. In particular, the impact of the successive addition of aromatic rings on the electronic properties was investigated by experimental (UV/Vis absorption, fluorescence, cyclic voltammetry) and theoretical studies (DFT). The physical properties recorded in solution and in the solid state showed that the P‐containing PAHs exhibit properties expected for an emitter in white organic light‐emitting diodes (WOLEDs).     

HIRFL–CSR加速器中束流与真空中剩余气体的碰撞损失

研究了重离子加速器中束流与真空中剩余气体的碰撞损失过程和碰撞截面,在依据大量实验数据的基础上,提出了一组计算离子一原子的电荷交换截面的经验公式.以兰州重离子加速器HDRFL及冷却储存环CSR为例,给出了依据碰撞截面的公式计算束流在加速器真空中的传输效率的方法,并计算了在不同真空度下HIRFL的ECR源轴向注入束运线、注入器SFC、前束运线、主加速器SSC和后束运线等不同加速阶段及CSR的传输效率,并提出合理的真空度要求.HIRFL的真空分布测量和束流的损失测量证明了该计算方法的可靠性.     

半导体激光器光束准直系统的功率耦合效率

在长距离无线光通信中，接收点光功率密度与光束发散角平方呈反比关系，为了获得小的发散角和大的功率耦合效率，要求准直系统有较大的数值孔径(NA)，但数值孔径过大会增加像差，因此合理设计功率耦合效率与准直系统的数值孔径就非常重要。该文对半导体激光器光束准直系统中功率耦合效率进行了研究，给出了半导体激光器光束功率耦合效率与k(孔径半径与孔径处等效光束半径之比)的关系表达式，并结合激光器光束准直系统，给出了半导体激光器光束功率耦合效率与准直系统数值孔径的关系表达式。该研究结论对于半导体激光器光束准直系统设计具有参考作用。     

Effect of the Parameters of Three-Mirror Resonators on the Spectral Characteristics of Single-Pulse Laser Generation with Self-Injection of Priming Radiation

Based on a semiclassical theory, investigations were made of the dynamics and spectral composition of pulsed generation with self-injection of priming radiation from the active part of a three-mirror linear resonator, the passive part of which contains an active loss modulator and serves as the output reflector of the laser. It is shown that there exists a range of resonator parameters at which pulsed lasing has virtually a single frequency irrespective of the detuning of the frequencies of the priming radiation and of the nearest eigenmode of the composite resonator. Considering graphically the phase conditions of generation, it is established that among pulsed lasers with self-injection of priming radiation which are constructed on the basis of three-mirror linear and branched resonators, the most efficient for creating single-frequency generation are those in which the length of the main resonator, where generation of the pulse occurs, is larger than the length of the additional one intended for forming the priming radiation. With an inverse ratio of the lengths of the resonators, the conditions of single-frequency pulsed generation becomes dependent on the priming radiation frequency.     

Novel model of FM-noise conversion in a UMZI using RF external phase modulation of lasers: Theoretical and experimental results

In this paper, we propose and demonstrate a new and original model for theoretical calculation and experimental measurement of the noise power spectral density (NPSD) in phase-modulated optical links. The phase modulation is operated in the RF frequency range by an external phase modulator. The NPSD is derived for the first time in interferometric systems, by considering all effects such as the 1/f FM noise of the laser and white noise applied to light from a 1550 nm DFB laser, with phase modulation. The results show for the first time the influence of the phase modulation index, modulation frequency and interferometric delay in the phase-to-intensity noise conversion. The experimental and simulation results of conversion of FM-noise to intensity noise in an optical link by considering the external RF phase modulation are shown with good agreement.     

A Novel Biomass Supported Na2CO3 System for Flue Gas Desulfurization

The breakthrough and stoichiometric SO2 adsorption efficiencies of a biomass supported Na2CO3 system (80 wt %Na2CO3/straw) have reached 48.9% and 80.6% respectively at a desulfurization temperature of 80℃.     

Er3+掺杂的Bi2O3-B2O3-SiO2玻璃的光谱性质

测试了Bi₂O₃-B₂O₃-SiO₂玻璃中的Er³⁺离子的吸收光谱、发射光谱、⁴I_13/2的荧光寿命、拉曼光谱,及OH^-的傅里叶红外吸收光谱。应用Judd-Ofelt理论计算了该玻璃中的Er³⁺离子的J-O参数、振子强度、⁴I_13/2能级的寿命,从而利用测得的⁴I_13/2的荧光寿命得出了⁴I_13/2能级的量子效率(15%)。由于较低量子效率可能与OH^-有关,所以计算了玻璃中的OH^-浓度,发现其浓度较高(1.66×10¹⁹cm^-1,相当于Er³⁺浓度的3倍)。应用McCumber理论和四能级模型计算了Er³⁺离子的受激发射截面和荧光发射光谱的半峰全宽,结果与通过吸收光谱计算所得基本吻合。根据透射率和折射率的关系计算了折射率,发现和测量值相差很大,说明有较大的散射,通过拉曼光谱和显微镜测试,认为是玻璃中的微小气泡造成的。     

基于液晶光阀的全息照相控光仪

设计了通过液晶光阀自动调整全息照相物光和参考光辐照比至最佳状态,同时能实现曝光时间自动控制的控光仪.该仪器巧妙运用液晶光阀和硅光电池器件,使测量、调整、自控一体化,从而提高拍摄优质全息图的工作效率.