Mutual influence of the morphology and capillary rheological properties in nylon/glass‐fiber/liquid‐crystalline‐polymer blends

Nylon‐6/glass‐fiber (GF)/liquid‐crystalline‐polymer (LCP) ternary blends with different viscosity ratios were prepared with three kinds of nylon‐6 with different viscosities as matrices. The rheological behaviors of these blends were characterized with capillary rheometry. The morphology was observed with scanning electron microscopy and polarizing optical microscopy. This study showed that although LCP did not fibrillate in binary nylon‐6/LCP blends, LCP fibrillated to a large aspect ratio in some ternary blends after GF was added. The addition of 5 wt % LCP significantly reduced the melt viscosity of nylon‐6/GF blends to such an extent that some nylon‐6/GF/LCP blends had quite low viscosities, not only lower than those of neat resins and nylon‐6/GF blends but also lower than those of corresponding nylon‐6/LCP blends. The mutual influence of the morphology and rheological properties was examined. The great reduction of the melt viscosity was considered the result of LCP fibrillation. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1619–1627, 2004     

Dispersion and distribution of organically modified montmorillonite in nylon‐66 matrix

Nylon‐66 nanocomposites were prepared by melt‐compounding nylon‐66 with an alkyl ammonium surfactant pretreated montmorillonite (MMT). The thermal stability of the organic MMT powders was measured by thermogravimetric analysis. The decomposition of the surfactant on the MMT occurred from 200 to 500 °C. The low onset decomposition temperature of the organic MMT is one shortcoming when it is used to prepare polymer nanocomposites at high melt‐compounding temperatures. To provide greater property enhancement and better thermal stability of the polymer/MMT nanocomposites, it is necessary to develop MMT modified with more thermally stable surfactants. The dispersion and spatial distribution of the organic MMT layers in the nylon‐66 matrix were characterized by X‐ray diffraction. The organic MMT layers were exfoliated but not randomly dispersed in the nylon‐66 matrix. A model was proposed to describe the spatial distribution of the organic MMT layers in an injection‐molded rectangular bar of nylon‐66/organic MMT nanocomposites. Most organic MMT layers were oriented in the injection‐molding direction. Layers near the four surfaces of the bar were parallel to their corresponding surfaces; whereas those in the bulk differed from the near‐surface layers and rotated themselves about the injection‐molding direction. The influence of the spatial distribution of the organic MMT on crystallization of nylon‐66 was also investigated. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1234–1243, 2003     

Influence of preparation methods on structure and properties of PA6/PA66 blends: A comparison of melt‐mixing and in situ blending

The blends composed of polyamide 6 (PA6) and polyamide 66 (PA66) were obtained using two different preparation methods, one of which was the melt‐mixing through a twin‐screw extruder and the subsequent injection molding; and the other, the in situ blending through anionic polymerization of ε‐caprolactam in the presence of PA66. For the former, there existed a remarkable improvement in toughness but a drastic drop in strength and modulus; however, for the latter, a reverse but less significant trend of mechanical properties change appeared. Various characterizations were conducted, including the analyses of crystalline morphology, crystallographic form, and crystallization and melting behaviors using polarized optical microscopy (POM), wide‐angle X‐ray diffraction (WAXD), and differential scanning calorimetry (DSC), respectively; observation of morphology of fractured surface with scanning electron microscope (SEM); measurement of glass transition through dynamic mechanical analysis (DMA); and the intermolecular interaction as well as the interchange reaction between the two components by Fourier transform infrared spectrometry (FT‐IR) and ¹³C solution NMR. The presence and absence of interchange reaction was verified for the in situ and melt‐mixed blends, respectively. It is believed that the transreaction resulted in a drop in glass transition temperature (T_g) for the in situ blends, contrary to an increase of T_g with increasing PA66 content for the melt‐mixed ones. And the two kinds of fabrication methods led to significant differences in the crystallographic form, spherulite size and crystalline content and perfection as well. Accordingly, it is attempted to explain the reasons for the opposite trends of changes in the mechanical properties for these two blends. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 1176–1186, 2007     

Electron diffraction investigation of PPTA/nylon 3T blends from shear-oriented anisotropic solutions

Nematic solutions of PPTA and nylon 3T were prepared in H₂SO₄ Optical microscopy was used to ascertain the phase behaviour of the blends. In the studied concentration range, no phase separation was observed. The solutions were shear-oriented and coagulated, and the resulting samples were studied by x-ray and electron diffraction. Nylon 3T crystallised even at a low concentration, which is indicative of a phase separation. Electron diffraction investigations of the oriented samples showed that well-oriented areas, which were predominantly composed of PPTA, adjoined areas where the major component, nylon 3T, showed no orientation. The relative proportion of the unoriented areas increased with increasing nylon concentration. It was concluded that, upon coagulation, the nylon was segregated into separate phases and crystallised unoriented, whereas for PPTA, crystallisation proceeded with very little chain rearrangement therefore preserving the orientation.     

SYNTHESIS AND CHARACTERIZATION OF ORGANOMONTMORILLONITE AND POLYAMIDE 66/MONTMORILLONITE NANOCOMPOSITES

The montmorillonites (MMTs), layered, smectite-type silicates, were premodified by two different methods priorto the polymer melt intercalation. In one case MMTs were modified with cetyltrimethylammonium bromide (CTAB), andtermed as organomontmorillonites (OMMTs); in the other case MMTs were modified by nylon, and the products were calledmodified montmorillonites (MMMTs). The effects of CTAB and nylon on the MMTs were investigated by using TG andWAXD. The results show that interlayer spacings of CTAN and nylon modified MMTs are larger than that of sodium MMTs.Then, polyamide 66 (PA 66)/MMT nanocomposites were obtained through the method of melt intercalation of polymers. Thenanocomposites were characterized by WAXD, TEM and Molau experiments. The results indicate that the MMTs dispersehomogeneously in the PA 66 matrix. The mechanical properties of nanocomposites, such as tensile properties and flexuralproperties, were also measured and show a tendency to increase with increase of MMT content and reach the maximumvalues at 5phr MMT content. The heat distortion temperature (HDT) of the nanocomposites (7 phr) is about 32 K higher thanthat of pure PA 66.     

含喹噁啉环的化合物改性聚己内酰胺

合成了14种由三种含喹(哑心)啉环的芳香化合物改性的聚己内酰胺(MC尼龙),并对其形态、抗冲击强度、吸水性及熔融行为等进行了表征。聚苯基单醚喹(哑心)啉(PPQ)单模型化合物对MC尼龙结晶部分几乎没有影响。少量(0.005—5.0％)吩嗪的引入使MC尼龙的颜色、形态及性能等发生巨大变化,改性体系被认为是氢键相互作用,PPQ双模型化合物的改性作用介于二者之间。     

Thermal Oxidative Stability of Heat-Stabilised Polyamide 66 by Differential Scanning Calorimetry

The thermal stability of heat-stabilised polyamide 66 in an oxidative environment is evaluated by DSC. The oxidative stability of the polyamide decreases as a result of repeated injection moulding. The results also indicate that the presence of glass fibres in the polyamide has a negative influence on the oxidative stability. Both isothermal and dynamic DSC measurements seem to be useful tools for assessing the stability of polyamides and there is a relationship between data determined using both procedures. This revised version was published online in July 2006 with corrections to the Cover Date.     

尼龙66/蒙脱土复合材料结晶行为的研究

在密炼机中采用熔融共混法制备蒙脱土重量分数为 2 5 %、4 5 %的尼龙 6 6 /蒙脱土复合材料 .通过DSC法对非等温结晶行为及在 2 2 8～ 2 4 0℃范围内的等温结晶行为进行研究 ,并与纯尼龙 6 6进行比较 .从其等温和非等温结晶行为的研究表明 ,蒙脱土起成核剂的作用 ,它的填入使尼龙 6 6结晶速率提高 ,但填料与基体间的相互作用使其链段运动困难 ,结晶活化能提高 ;在研究的填料含量变化范围内 ,结晶行为变化不大 ,并且找到该复合材料在 2 2 8～ 2 34℃范围结晶对温度的不敏感区 ;对非等温结晶过程分析 ,刘结平 莫志深方程是适用的 ,而Ozawa方程则是不适用的 .     

尼龙1010／尼龙6共聚物的表观相图研究

采用显微熔点法和ＤＳＣ测定了尼龙１０１０／尼龙６共聚物的表观相图；分析了投料比与链节结构单元含量的关系。最低熔点时尼龙１０１０／尼龙６的理论重量投料比为６０／４０，摩尔比为３３．３／６６．７，实验结果与此相近。     

The discovery of polymer‐clay hybrids

The first successful example of a polymer‐clay hybrid was nylon‐clay hybrid (NCH), which is a nano‐meter‐sized composite of nylon‐6 and 1‐nm‐thick exfoliated aluminosilicate layers of the clay mineral. NCH was found and developed at Toyota Central Research and Development Laboratories over 17 years ago. The NCH containing a few weight percentages of clay exhibits superior properties such as high modulus, high strength, and good gas‐barrier properties. The key for the discovery of NCH was the polymerization of a nylon monomer in the interlayer space of the clay. This highlight presents the development of NCH from its discovery to its commercialization. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 819–824, 2004