A post curing strategy toward the feasible covalent adaptable networks in polyacrylate latex films

The implementation of covalent adaptable networks (CANs) in general resin system is becoming attractive. In this work, we propose a simple post-curing strategy based on the core-shell structured acrylate latex for the achievement on both the improved general performance and the CANs characteristics in latex films. The building to the CANs was relied on the introduction of 4,4′-diaminophenyl disulfide as the curing agent, which cured the acetoacetoxy decorated shell polymer through the ketoamine reaction. The metathesis reaction of aromatic disulfides in the crosslinking segments enabled the thermally induced dynamic behavior of the network as revealed in the stress relaxation tests by comparison with other diamine crosslinking agents without the incorporation of disulfide. The synergism of the dynamic crosslinking of the shell polymer and static crosslinking in the core polymer contributed to the improved mechanical strength (15 MPa, strain% = 250%) and the suppressed water adsorption (~1% in 24 h of soaking) of the latex film, which exhibited above 90% of recovery in both strength and strain from a cut-off film damage within 1 h at 80°C. Moreover, the cured latex film could be recycled, and 75% of the mechanical performance was regained after three fragmentation-hot-pressing cycles. These, in addition with the feasible and environmental friendly characteristics, suggest a sustainable paradigm toward the smart thermosetting latex polymers.     

煤直接液化油中混合酚的分离研究

利用分子筛择形特点，对煤直接液化油中的混合酚实施高效分离。本研究选取间甲酚和对甲酚作为分离煤直接液化油馏分段混合酚的模型化合物，采用化学液相沉积法对HZSM-5吸附剂的孔口结构进行改变，分析分子筛硅铝比及颗粒粒径对模型化合物间甲酚和对甲酚吸附分离性能的影响，以获得高性能固相吸附剂，并将其应用于180-190℃馏分段混合酚分离。结果表明，当分子筛硅铝比为25、粒径为3-5 μm时，分子筛的孔口结构调节效果最优；当正硅酸乙酯的最小用量为0.2 mL/g时，固相吸附剂的吸附量为0.03 g/g，对甲酚选择性高于95%。由于外表面沉积物对吸附剂的孔口结构变化，导致对甲酚选择性的提高。进一步采用HZSM-5（1）吸附剂对真实煤直接液化油混合酚的分离中发现，苯酚和对甲酚的选择性均达到100%。     

Precise Synthesis and Thin Film Self-Assembly of PLLA-b-PS Bottlebrush Block Copolymers

The ability of bottlebrush block copolymers (BBCPs) to self-assemble into ordered large periodic structures could greatly expand the scope of photonic and membrane technologies. In this paper, we describe a two-step synthesis of poly(l-lactide)-b-polystyrene (PLLA-b-PS) BBCPs and their rapid thin-film self-assembly. PLLA chains were grown from exo-5-norbornene-2-methanol via ring-opening polymerization (ROP) of l-lactide to produce norbornene-terminated PLLA. Norbonene-terminated PS was prepared using anionic polymerization followed by a termination reaction with exo-5-norbornene-2-carbonyl chloride. PLLA-b-PS BBCPs were prepared from these two norbornenyl macromonomers by a one-pot sequential ring opening metathesis polymerization (ROMP). PLLA-b-PS BBCPs thin-films exhibited cylindrical and lamellar morphologies depending on the relative block volume fractions, with domain sizes of 46–58 nm and periodicities of 70–102 nm. Additionally, nanoporous templates were produced by the selective etching of PLLA blocks from ordered structures. The findings described in this work provide further insight into the controlled synthesis of BBCPs leading to various possible morphologies for applications requiring large periodicities. Moreover, the rapid thin film patterning strategy demonstrated (>5 min) highlights the advantages of using PLLA-b-PS BBCP materials beyond their linear BCP analogues in terms of both dimensions achievable and reduced processing time.     

Recent advances on the use of active anodes in environmental electrochemistry

Active anodes, especially those consisting of metal mixed oxides (MMOs) containing Ru and/or Ir oxides, have been applied in the treatment of wastewater, especially when chloride ions are present. Their characteristics continuously drive the study of applications of these materials, be they in the degradation of different organic molecules, the preparation of new electrode materials and in the association of various processes to increase pollutant removal. Thus, this brief review aims to present some of the recent advances in the application of active anode materials in environmental electrochemistry. Focussing on the 2018–2020 period, it is possible to note many applied studies, using commercially available materials, covering a wide range of target pollutants. Still other studies aim to modify the catalyst surfaces to increase the mineralization capacity, and the use of these anodes in the production of free chlorine species to mediate indirect organic reduction is observed.     

Strain effects on multiferroic BiFeO3 films

The field of multiferroics has experienced a rapid progress resulting in the discovery of many new physical phenomena. BiFeO₃ (BFO) compound, which is one of the few room-temperature single-phase multiferroics, has contributed subsequently to this progress. As a result, significant review articles have been devoted specifically to this famous system. This chapter is dedicated to the strain effects on the structure stability and property changes of BFO thin films. It is a short and non-exhaustive topical overview that may be seen as an invitation for interested readers to go beyond. There is a very active and prolific research in this field and we apologize to the authors whose relevant work is not cited here. After a short introduction, we will thus review the effect of strain on BFO films by describing the consequences on the structure and the phase transitions as well as on polar, magnetic and magnetoelectric properties.     

基于DIS数字信息化系统对透光物质透光性能的研究

采用DIS数字信息化系统,对不同浓度的蓝墨水溶液在激光光源照射下的透射平均照度及照度分布图像进行实验研究,得到了平均照度值随溶液浓度变化的规律。对不同颜色塑料膜片对白炽灯光源透过照度值及照度分布图像进行实验研究得到及其相关之规律。     

Organic–Inorganic Hybrid Gold Halide Perovskites: Structural Diversity through Cation Size

Crystal structures of a series of organic–inorganic hybrid gold iodide perovskites, formulated as A₂[Au^II₂][Au^IIII₄] [A=methylammonium (MA) ( 1 ) and formamidinium (FA) ( 2 )], A′₂[I₃]_1−x[Au^II₂]_x[Au^IIII₄] [A′=imidazolium (IMD) ( 3 ), guanidinium (GUA) ( 4 ), dimethylammonium (DMA) ( 5 ), pyridinium (PY) ( 6 ), and piperizinium (PIP) ( 7 )], systematically changed depending on the cation size. In addition, triiodide (I₃⁻) ions were partly incorporated into the AuI₂⁻ sites of 3 – 7 , whereas they were not incorporated into those of 1 and 2 . Such a difference comes from the size of the organic cation. Optical absorption spectra showed characteristic intervalence charge-transfer bands from Au^I to Au^III species, and the optical band gap increased as the size of the cation became larger.     

Characterization of ZnO:AI films deposited by r.f.magnetron-sputtering at low temperature

Transparent conducting ZnO:AI thin films with good adhesion and Iow resistivity have been prepared on organic substrates and Coming 7059 glass substrates by r.f. magnetron-sputtering technique at Iow substrate temperature (25-210℃). Structural and photoelectric properties of the deposited films are investigated. The deposited films are polycrystalline with hexagonal structure and a preferred orientation with the c-axis perpendicular to the substrate. Only the (002) peak is observed.High quality films with resistivity as Iow as 1.0 x 10- 3Ω@ cm and 8.4 x 10- 4Ω@ cm, the average transmittance over 74% and 85% in the wavelength range of the visible spectrum have been obtained on different substrates.     

(111)择优取向的Pb(Zr0.52Ti0.48)O3铁电薄膜的制备及研究

选用不同浓度的Pb(Zr_0.52Ti_0.48)O₃溶胶，用Sol-gel法在Pt/Ti/SiO₂/Si基片上沉积一层厚度不同的Pb(Zr_0.52Ti_0.48)O₃ (PZT52)过渡层，经400℃烘烤、550℃退火等程序后，再用Sol-gel法在PZT52过渡层上沉积Pb(Zr_0.52Ti_0.48)O _{关键词： PZT铁电薄膜 择优取向 过渡层 剩余极化强度}     

Nonsensitiveness Regions for Threshold Ellipsoids

The problem is to determine nonsensitiveness regions for threshold ellipsoids within a regular mixed linear model.