Proteinases from Carica papaya Latex

Data on the proteinase complex from Carica papaya latex were reviewed. The properties and applications of the domestic preparation cucumazyme and known medicinal preparations based on papaya proteinases (caripazyme, lecozyme, lecopain) were compared.     

Adhesion studies of latex film surfaces on the meso- and nanoscale

In this paper the effects of surface roughness and annealing temperature (T) of latex coating films on adhesion are discussed for the different stages of the film formation process. The surface free energy of latex films was assessed in terms of practical work of adhesion (W) (or adherence) using a custom-built adhesion-testing device (ATD), atomic force microscopy (AFM), and contact angle measurements. For preannealed latex films surface roughness averages (R_a) were determined from AFM height images and were related to the values of W obtained from ATD measurements at room temperature. The results obtained using these tests exhibiting surface behavior on different length scales indicate a dependence of the measured adhesion on surface roughness and temperature, as well as on the length scale of the measurements.First preannealed samples were studied, which were obtained by heat treatment above the respective glass transition temperatures (T_g). Increasing the temperature of preannealing resulted in a decrease of the adherence observed in ATD experiments at room temperature. However, on the nanoscale, using AFM, no significant variation of the adherence was observed. This observation can be explained by roughness arguments. Preannealing decreases roughness which results in lower adherence values measured by ATD while for essentially single asperity AFM experiments roughness has an insignificant effect. Specimens were also annealed over a constant period of time (90 min) at different temperatures. At the end of the heat treatment, adhesion was measured at the treatment temperature by ATD. The amplified effect of temperature observed in this case on adherence is attributed to the combination of roughness decrease and increasing test temperature. In a third set of experiments completely annealed samples were studied by ATD as well as by AFM as a function of temperature. With increasing T values ATD showed a decrease in adherence, which is attributed to a decreasing surface free energy of the annealed films at elevated T values. AFM, on the other hand, showed an opposite trend which is assigned to increasing penetration of the tip into the tip/wetting polymer samples versus increasing temperature. Finally, annealing isotherms as a function of time were investigated by ATD in situ at different temperatures. This last set of experiments allowed us to optimize annealing time and temperature to achieve complete curing.     

乳液聚合阶段Ⅱ动力学研究的进展

本文简述了乳浓聚合动力学研究的进展,着重于澳大利亚Sydney大学Gilbert等在乳液聚合阶段Ⅱ动力学方面的研究概况。介绍了不同水溶性单体的小尺寸种子乳液体系的SmithEwart递推方程的求解方法及其解析解形式和乳液聚合动力学数据的处理。同时讨论了该研究的局限性。     

Early-stage flocculation kinetics of polystyrene latex particles with polyelectrolytes studied in the standardized mixing: Contrast of excess and moderate polyelectrolyte dosage

Standardized mixing procedure was applied to the analysis of flocculation of polystyrene latex (PSL) particles with polyelectrolytes. After confirming the initial enhancement of flocculation rate in the very beginning followed by abrupt stop with excess dosage, attention was shifted to the system of moderate dosage. In the former, effects of ionic strength were further analyzed to find the consistency with adsorption isotherm. In the latter, flocculation started slowly in the beginning, sometime slower than salt-induced rapid coagulation, however, the rate gradually increases in the middle stage. Often, the increased rate exceeds that of salt-induced rapid coagulation. This behavior emerged more clearly in the case of lower ionic strength. This is the indication that the rate of relaxation of polymer on the colloidal surface is a function of surface coverage and ionic strength. The ultimate degree of flocculation is usually higher than that observed for excess dosage. The size distribution of flocs was also examined, however, no clear difference between different experimental conditions was confirmed for the same degree of flocculation.     

Synthesis and characterization of surface-cyanofunctionalized poly (N-isopropylacrylamide) latexes

 A series of P[N-isopropylacrylamide (NIPAM)] latexes with different contents of cyano groups were successfully prepared by either seeded or shot-growth polymerizations of an aqueous solution containing acrylonitrile (AN) onto a seed P[NIPAM] latex, respectively, and further characterized by FT-IR, ¹H-NMR, elemental analysis, as well as by quasielastic light scattering (QELS) and scanning electron microscopy (SEM). All prepared surface-cyanofunctionalized P[NIPAM] latexes exhibited the same range of lower critical solution temperature (LCST) as a pure P[NIPAM] latex. The shot polymerization process proved more efficient at yielding cyano derivatized latexes than the seeded polymerization technique. The amount of incorporated cyano groups onto the particles was determined with a good correlation both by ¹H-NMR and elemental analysis. The higher the amount of initially introduced AN monomer in the reaction mixture, the more cyano groups were incorporated onto the particles. The surface of the particles with high content of cyano groups appeared quite rough by SEM in comparison with that of the pure P[NIPAM] particles. Received: 25 February 1998 Accepted: 23 June 1998     

Nanocomposite materials from latex and cellulose whiskers

Composite materials were processed by casting a mixture of aqueous suspensions of latex and microfibrils. These microfibrils, or whiskers, are extracted from a sea animal and are monocrystals of cellulose, with an aspect ratio around 100 and an average diameter of 20 nm. It has been found that the mechanical properties (shear modulus) are increased by more than two orders of magnitude in the rubbery state of the polymeric matrix, when the whisker content was 6% (w/w). This very large effect is discussed on the basis of different types of mechanical models and it is concluded that these whiskers form a rigid network, probably linked by hydrogen bonds. The formation of this network is assumed to be governed by a percolation mechanism.     

Mass transfer and benzene removal from air using latex rubber tubing and a hollow-fiber membrane module

A dense-phase latex rubber tube and a polyporous propylene hollow-fiber membrane module (HFMM) were investigated for control of benzene-contaminated gas streams. The abiotic mass flux observed through the latex tube was 3.9–13 mg/(min·m²) for 150 ppm of benzene at various gas and liquid flow rates, while a 100-fold lower mass flux was observed in the HFMM. After seeding with an aromatic-degrading culture enriched from activated sludge, the observed removal was 80% of 150 ppm, corresponding toa mass flux of 45 mg/(min·m²). The observed mass flux through the HFMM during biofiltration also rose, to 0.4 mg/(min·m²). Because the HFMM had a 50-fold higher surface area than the latex tube, the observed ben zene removal was 99.8%. Compared to conventional biofilters, the two reactors had modest elimination capacities, 2.5–18 g/(m³·h) in the latex tube membrane bioreactor and 4.8–58 g/(m³·h) in the HFMM. Although the HFMM had a higher elimination capacity, the gas-phase pressure drop was much greater.     

核-壳型聚丙烯酸酯复合乳液

简述了核-壳型聚丙烯酸酯复合乳液的合成方法、形态及其影响因素与判断方法、结构与性能等方面的研究进展;认为核-壳型复合乳液膜机械性能优良的原因是:核、壳两相间存在的过渡区适当地抑制了二者的相分离。     

MAA存在下VAc/BA核壳乳液聚合过程中的胶粒形态研究

用ＴＥＭ和电位滴定法对不同配方和工艺条件得到的胶粒形态结构和羧基分别进行了表征。结果表明：加入甲基丙烯酸有利于胶粒的稳定和形成规则的核壳胶粒。半连续加料不会形成完全反转的核壳结构,但是,核层在反应过程中由于聚合物簇的迁移会造成形变。由于胶粒中聚合物浓度高,粘度大,因而胶粒形态变化受动力学影响甚大,羧基分布主要是由动力学确定的。     

Thermal Emulsion Polymerization without any Conventional Initiators and Emulsifiers

Stable poly(styrene-co-sodium styrene sulfonate) (P(St-NaSS) nanoparticles with broader size distribution were synthesized by thermal emulsion polymerization without any conventional initiators and emulsifiers. The obtained polymer nanoparticles have higher ξ potential, and the particle sizes have broad distribution. The stability of polymer particles originated from the addition of small amounts of ionic comonomer, NaSS, which can act as an emulsifier in somewhat. The monomer conversion could reach up to about 28 wt% in 48 h, and did not increase by further polymerization when higher polymerization temperature (120 ℃) was employed. This polymerization system may be give some further understand for mechanism of emulsion polymerization.