The Effects of Beating,Web Forming and Sizing on the Surface Energy of <Emphasis Type="Italic">Eucalyptus globulus</Emphasis> Kraft Fibres Evaluated by Inverse Gas Chromatography

In this work attention has been focused on the effects of papermaking beating, web forming and sizing operations on the physical/chemical surface properties of bleached Eucalyptus globulus kraft fibres. Inverse gas chromatography (IGC) was used to determine the dispersive component of surface tension (γ_s^d) as well as the acidic/basic character (according to the Lewis concept) of the solid surfaces (pulp fibres and pulp handsheets). The results have shown that the main effect of beating is to increase the fibre's Lewis acidic character. Web forming caused a strong decrease in γ_s^d and significant increments in the adhesion works of both acidic and basic probes, lowering the ratio between the two. Nevertheless, the surface of handsheets still exhibited a dominant acidic character. The sizing operation did not change the dispersive component of the surface tension significantly but decreased the difference between the adhesion works of the acidic and basic probes, rendering the handsheet surface less Lewis acidic and more Lewis basic. Thus, although internal sizing is expected to strongly influence liquid spreading at the paper surface and liquid penetration of the fibre's network, it is concluded that beating and web forming lead to important changes in the surface energetic properties of the Eucalyptus globulus kraft fibres.     

Enzymatic bleaching of organosolv sugarcane bagasse pulps with recombinant xylanase of the fungus Humicola grisea and with commercial cartazyme HS xylanase

Organosolv (ethanol/water and acetosolv) pulps were treated with Humicola grisea var. thermoidea and compared with Cartazyme HS xylanase-treated pulp. The ethanol/water pulps treated with H. grisea had the same viscosity as unbleached pulps (8 cP). Ethanol/water pulps treated with Cartazyme had higher viscosity than H. grisea-treated pulps (12 cP). Acetosolv pulps treated with H. grisea and Cartazyme presented a reduction in viscosity; however, the pulps treated with H. grisea had a lower reduction in viscosity than Cartazyme-treated pulps. Ethanol/water pulps treated with H. grisea had a 23% reduction in kappa number in 4 and 8 h of treatment, compared with the unbleached pulps. Cartazyme-treated pulps had a kappa number similar to that of the control pulps for 4 h of treatment. Extending the treatment time to 12 h resulted in a reduction of 33%. The acetosolv pulp treated with H. grisea had a kappa number reduced to 23% in 4 h. Cartazyme treatment resulted in a reduction of 55 and 44% in kappa number for 4 and 8 h of treatment, respectively, when compared with control pulp. Extending the treatment time to 12 h decreased the kappa number 72%. Fourier transform infrared spectra and principal component analysis showed differences among unbleached, H. grisea-treated, and Cartazyme-treated pulps.     

Molecular properties of hemicelluloses located in the surface and inner layers of hardwood and softwood pulps

The molecular properties of hemicelluloses located in the surface and inner layers of fibers present in hardwood and softwood pulps, together with the effects of different bleaching processes on these properties, have been investigated in this study. In order to separate the hemicelluloses located in these two layers, fibers were subjected to mechanical peeling and then separated by filtration into surface (filtrate) and inner layer materials. The materials thus obtained were characterized with respect to their polysaccharide compositions and uronic acid contents. The molar mass parameters of the hemicelluloses (extracted by alkali) were determined by employing size-exclusion chromatography in combination with off-line MALDI mass spectrometry. For all of the pulps examined, the relative content of xylan was found to be greater in the surface layer of the fiber than in the corresponding inner layer. The xylan polymers of the surface layer exhibited higher molar masses and lower frequencies of uronic acid side groups than did the xylans in the inner fiber layer. In connection with ozone treatment, hexenuronic acid residues in the surface layer xylan were removed to a greater extent than in the case of the inner layers, indicating a gradient for the reaction with ozone across the fiber wall. The xylan polymer remaining on the surface of the softwood pulps after completion of the chlorine dioxide bleaching process was predominantly uncharged.     

The Degree of Disorder in Hardwood Kraft Pulps Studied by Means of LODP

The amount of disordered material in two types of hardwood kraft pulps was estimated by determining the weight loss at the point where the levelling-off degree of polymerisation (LODP) was reached. The pulps used were commercial pulps viz (1)one conventional birch kraft and (2)one mixed hardwood (MHW) kraft pulp that had been prehydrolysed prior to cooking. The results indicated that the hemicellulose xylan is closely associated with the cellulose in commercial birch pulps. It is therefore only possible to use LODP as a measure of the crystallite length of hardwood cellulose in highly purified pulps, such as prehydrolysed kraft pulp. A model explaining the LODP-results is proposed.     

Novel Sulfanilamide as Potent Surfactants and Antibacterial Agents

Sulfanilamide derivatives of the type RØSO₂NHR in which substitution at both the amino and amido nitrogen have been synthesized where R = NHCOCH:CHCOOH, NHCOCH₂CH₂COOH, NHCH₂CH(OH)CH₂SO₃Na, N⁺(CH₃)₃I^? and NHCH₂CH(OH)CH₂N⁺(C₂H₅)₃Cl^? and R′ = butyl, cyclohexyl, and decyl. The unique structural features of these sulfanilamides were confirmed by infrared, proton magnetic resonance and elemental analysis. Most of these compounds exhibited good water solubility and surface activity. Wetting ability and tendency of enhancing oil/water emulsification were related to the structure of the substituents in sulfanilamide molecule. Furthermore, the peculiar of molecular structure of these sulfanilamide surfactants imparts distinguished antimicrobial activity to these molecular species against some Gram positive and Gram negative bacteria.     

Distribution of free amino acids,polyphenols and sugars of Ziziphus jujuba pulps harvested from plants grown in Tunisia

Ziziphus jujuba pulps are very much appreciated by the inhabitants and have been recently exported. This article reports on the chemical composition (amino acids, polyphenols and sugars) of the pulps of four Z. jujuba ecotypes (Choutrana, Mahdia, Mahres and Sfax). The major amino acids identified were proline, aspartic acid and glutamic acid. Among these, proline was the most abundant amino acid (17.4 mol). Considerable differences in total phenolic contents (15.85 mg/L) were found. Predominant phenols identified by using HPLC were rutin (1.09 mg/L) and chlorogenic acid (2.57 mg/100 g). Sugars isolated from Ziziphus pulps were found at a rate of 43.52%. Using HPLC method, three sugars from the pulp extract were identified: glucose, galactose and sucrose. The Mahdia ecotype was the richest in these sugars with 0.45, 136.51 and 113.28 mg/L, respectively.     

Effect of unmodified kraft lignin concentration on the emulsion and miniemulsion copolymerization of styrene with n‐butyl acrylate and methacrylic acid to produce polymer hybrid latex

The introduction of non‐modified kraft LignoBoost® lignin (KL) to produce polymer hybrid latex has received much attention in recent years because it is derived from renewable resources. The focus of this work is to develop a polymer hybrid latex by emulsion and miniemulsion copolymerization of styrene with n‐butyl acrylate and methacrylic acid in the presence of different concentrations of KL furnished by the pulp and paper industry. The study intends to substitute a styrene in the system to understand the effect of non‐modified KL on the properties not only of the latexes, but also on the copolymers themselves. Each polymerization was carried out by shot‐process of tertbutyl hydroperoxide and sodium formaldehyde sulfoxylate as the redox system. The polymer latexes were characterized in relation to overall conversion, particle diameter, particle morphology, coagulum formation, surface tension, zeta potential, and atomic force microscopy. The polymers were evaluated through gel permeation chromatography, water absorption, and thermal properties. The results show that the addition of non‐modified KL results in inhibition of the polymerization and that KL acts as a colloid stabilizer. Small particles were generated in the initial stages of the polymerizations. The presence of the KL altered the color of the latexes; the increase in KL concentration resulted in increase in the absorption of water of the polymer films; the increase in KL concentration resulted in decrease of the molar mass of the copolymers.     

The first 85% kraft lignin-based thermoplastics

Interest in the development of lignin-containing polymeric materials has been upheld more or less continuously for the past 20 years. Tendencies toward high moduli and poorly defined thermal transitions have been regarded as imposing inevitable limitations upon the use of lignin derivatives for such purposes. Incorporation of more than 25–40% (w/w) lignin had usually resulted in materials that were brittle and weak. For the first time, however, from homogeneous blends containing 85% (w/w) underivatized industrial kraft lignin with poly(vinyl acetate) and two plasticizers, a series of thermoplastics has been fabricated with promising mechanical properties. The tensile behavior of these new polymeric materials depends directly upon the degree of association between the intrinsic kraft lignin components. In extending to values about 25 MPa and 1.5 GPa, respectively, the tensile strengths and Young's moduli vary linearly with the effective M̄_w for the kraft lignin species, under conditions where the proportions of the individual molecular components, both associated and discrete, do not change. Moreover, melt-flow index measurements indicate that these polymeric materials are amenable to thermal processing by extrusion molding. Thus a significant step has been taken toward developing a new generation of thermoplastics that are lignin-based in a very fundamental way. © 1997 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 35: 1899–1910, 1997     

Evaluation of new organosolv dissolving pulps. Part II: Structure and NMMO processability of the pulps

The supermolecular structure of dissolving pulps produced from hardwood by the organosolv processes Acetosolv, Formacell, and Milox was characterized by physical methods (TEM, WAXS, SAXS, NMR) and compared with conventional Sulfite and standard commercial dissolving pulps. The suitability of the pulps for the NMMO technology was tested by spinning fibres and blowing films, whose structural and mechanical properties have also been determined. With TEM it was shown that the TCF-bleached organosolv pulps have only the primary (Formacell), the primary and S1 (Milox), or mainly the S1 (Acetosolv) layers exposed to the surface, whereas Sulfite pulping exposes the S2 cell wall layer. Especially for Milox and Acetosolv Eucalyptus wood pulps, a reduced degree of crystallinity was found, both with WAXS and NMR. The SAXS results indicate a lower pore intersection length for the new pulps as compared to conventional pulps. Unbleached organosolv pulps show a lower crystallinity, very low pore intersection lengths, and an average crystallite shape different from their bleached counterparts. The dissolution behaviour in NMMO and the processability of the bleached organosolv pulps was satisfactory so far. Fibres and films could be produced with structural and mechanical properties comparable with conventional Sulfite and standard commercial dissolving pulp products. However, unbleached organosolv pulps did not meet the requirements of the NMMO process.     

A comparative CP/MAS 13C-NMR study of cellulose structure in spruce wood and kraft pulp

CP/MAS ¹³C-NMR spectroscopy in combination with spectral fitting was used to study the supermolecular structure of the cellulose fibril in spruce wood and spruce kraft pulp. During pulping, structures contributing to inaccessible surfaces in the wood cellulose are converted to the cellulose I allomorph, that is, the degree of order is increased. This increase is also accompanied by a conversion of cellulose I to cellulose I. Cellulose from wood composed of different cell types, that is, compression wood, juvenile wood, earlywood, latewood and normal wood exhibited a similar supermolecular structure. Assignments were made for signals from hemicellulose which contribute significantly to the spectral C-4 region (80–86 ppm) in kraft pulp spectra but substantially less to the corresponding region in wood spectra.