Formation of porous polymer morphology by microsyneresis during divinylbenzene polymerization

This article describes the investigation of the importance of various reaction conditions on microsyneretic pore formation during polymerization of divinylbenzene (DVB) under so‐called “solvothermal” conditions. To induce microsyneretic pore formation, the most important parameter is an unusually high dilution of monomers with a “good” porogen solvating the polymer chains. High dilution and solvation of the growing poly(DVB) chains promote the prolongation of the polymer chains rather than their interconnection by crosslinking. Consequently, when the polymer gel density reaches the point where syneresis starts, the polymer network is geometrically too extensive to be broken up into precipitating entities and, instead, porogen droplets are formed within the continuous polymer gel. The pore geometry created by microsyneresis offers high surface area in wide mesopores and hence, high capacity for supporting functional groups or reactions with much better accessibility than narrow pores between polymer microspheres produced by macrosyneresis in conventional styrenic polymer supports. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 774–781     

Sulfur Concentration in Nanoporous Alumina Membrane

Nanoporous alumina membrane prepared by anodic oxidation using sulfuric acid electrolyte was subjected to TG-DTA and X-ray Photoelectron Spectroscopy (XPS or ESCA) to further study the distribution of sulfur. In XPS study, Ar⁺ ion bombardment was performed on the sample to etch the surface at a rate of 3 nm min^-1. As a result, sulfur was found to be concentrated within a depth of 3nm from the surface. The S content of the surface was found to be 2.7±0.5 wt%, and that at a depth of ca. 3 nm and ca. 10 nm was found to be as low as about 0.6±0.11 wt% (5.37±1.0 wt%→ 1.26±0.2wt% SO₂). In TG-DTA, the mass loss of 7.3% was in fair agreement with that calculated on XPS results (7.1±1.2%). This revised version was published online in July 2006 with corrections to the Cover Date.     

Supramolecular Templating of Mesopores in Phase-Separating Silica Sol-Gels Incorporated with Cationic Surfactant

Silica gels with hierarchical macropores and mesopores have been prepared by inducing phase separation in the alkoxide-based sol-gel system with an addition of alkyltrimethylammonium salt. Narrowly distributed mesopores were observed in the heat-treated gel samples possibly as a result of supramolecular templating of silica oligomers in the reacting solution. The ionic attractive interaction and hydrophobicity of the attached alkyl group cooperatively determined the phase separation tendency. No indication of long-range order of the mesopores was obtained.     

Diffusion Mechanisms of Zeolite Catalysts

The diffusion mechanisms within zeolite catalysts, such as resistance to diffusion at pore mouths, configurational diffusion, adsorption-controlled diffusion, influence of co-existing molecules and pore blocking, were overviewed. Two kinds of diffusivities, the intracrystalline diffusivity and the effective diffusivity, were discussed separately to clarify the diffusion mechanism.     

Trapping Copper Phthalocyanine in a Silica Sono-Xerogel

A copper phthalocyanine (CuPc) has been encapsulated in silica. The trapping effects were studied comparing the UV-Vis absorption spectra of some CuPc solutions and composites prepared under different conditions. The trapped organic molecules’ stability was monitored during the gelation and drying processes. Leachability test have been carried out with the aim of checking the trapping efficiency. Hydrolysis water of pH=2 and a molar ratioR _w =6 mol acid H₂O/mol TMOS leads to a higher CuPc stacking angle homogeneity. The increase of Pc induces a narrower mesopore distribution and helps the stabilization of the composite.     

键阻断原理构建中孔A型沸石

采用不同类型的有机硅烷化SiO₂作为基本合成单元, 制备了具有晶内中孔的A型沸石。考察了反应碱度、Si/Al比、晶化时间等合成条件对产品的影响。结果表明, 甲氨基丙基三甲氧基硅烷是合成中孔A型沸石的最佳硅烷化试剂;硅烷化试剂的应用, 使中孔沸石晶化过程可以通过“键阻断原理”有效控制;沸石的中孔尺寸可以通过不同类型的有机硅烷化试剂进行调控; 一定范围内, 其外比表面积、中孔体积随SiO₂表面硅烷化度的增加而增加。通过沸石晶化过程中的“键阻断”, 可以制备具有晶内中孔的A型沸石。     

键阻断原理构建中孔A型沸石

采用不同类型的有机硅烷化SiO2作为基本合成单元,制备了具有晶内中孔的A型沸石。考察了反应碱度、Si/Al比、晶化时间等合成条件对产品的影响。结果表明,苯胺基丙基三甲氧基硅烷是合成中孔A型沸石的最佳硅烷化试剂;硅烷化试剂的应用,使中孔沸石晶化过程可以通过"键阻断原理"有效控制;沸石的中孔尺寸可以通过不同类型的有机硅烷化试剂进行调控;一定范围内,其外比表面积、中孔体积随SiO2表面硅烷化度的增加而增加。通过沸石晶化过程中的"键阻断",可以制备具有晶内中孔的A型沸石。     

Synthesis of Nitrogen‐Doped Mesoporous Carbon Spheres with Extra‐Large Pores through Assembly of Diblock Copolymer Micelles

The synthesis of highly nitrogen‐doped mesoporous carbon spheres (NMCS) is reported. The large pores of the NMCS were obtained through self‐polymerization of dopamine (DA) and spontaneous co‐assembly of diblock copolymer micelles. The resultant narrowly dispersed NMCS possess large mesopores (ca. 16 nm) and small particle sizes (ca. 200 nm). The large pores and small dimensions of the N‐heteroatom‐doped carbon spheres contribute to the mass transportation by reducing and smoothing the diffusion pathways, leading to high electrocatalytic activity.     

Adsorption properties and porous structure of new carbon materials

The adsorption properties of the new carbon materials, sibunites, which are mesoporous samples with a developed surface of pores, were studied. The isotherms of the adsorption of benzene vapor were determined to estimate the porous structure of these materials. The principal methods for calculating the parameters of the porous structure of sibunites were analyzed. The application of the BET equation even in the presence of a small number of micropores can distort the results, therefore the most suitable method for estimating the surface of mesopores is one that is based on the Dubinin—Zaverina equation. The estimation of the surface of sibunites using water vapor adsorption is demonstrated.Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 8, pp. 1377–1380, August, 1993.     

Micron-Sized Zeolite Beta Single Crystals Featuring Intracrystal Interconnected Ordered Macro-Meso-Microporosity Displaying Superior Catalytic Performance

Zeolite Beta single crystals with intracrystalline hierarchical porosity at macro-, meso-, and micro-length scales can effectively overcome the diffusion limitations in the conversion of bulky molecules. However, the construction of large zeolite Beta single crystals with such porosity is a challenge. We report herein the synthesis of hierarchically ordered macro-mesoporous single-crystalline zeolite Beta (OMMS-Beta) with a rare micron-scale crystal size by an in situ bottom-up confined zeolite crystallization strategy. The fully interconnected intracrystalline macro-meso-microporous hierarchy and the micron-sized single-crystalline nature of OMMS-Beta lead to improved accessibility to active sites and outstanding (hydro)thermal stability. Higher catalytic performances in gas-phase and liquid-phase acid-catalyzed reactions involving bulky molecules are obtained compared to commercial Beta and nanosized Beta zeolites. The strategy has been extended to the synthesis of other zeolitic materials, including ZSM-5, TS-1, and SAPO-34.