Influence of SiO2 in SiCp on the microstructure and impact strength of Al/SiCp composites fabricated by pressureless infiltration

The effect of SiO₂ in SiC_p and the following processing parameters on the microstructure and impact strength of Al/SiC_p composites fabricated by pressureless infiltration was investigated: Mg content in the aluminum alloy, SiC particle size, and holding time. Preforms of SiC_p in the form of rectangular bars (10 × 1 × 1 cm) were infiltrated at 1150°C in an argon→nitrogen atmosphere for 45 and 60 min by utilizing two aluminum alloys (Al-6 Mg-11 Si and Al-9 Mg-11 Si, wt.%). The results obtained show that the presence of SiO₂ in SiC affects the microstructure and impact strength of the composites significantly. When Al₄C₃ is formed, the impact strength decreases. However, a high proportion of SiC to SiO₂ limits the formation of the unwanted Al₄C₃ phase in the composites. Also, a higher content of Mg in the Al alloy lowers the residual porosity and, consequently, increases the composite strength. The impact strength grows with decrease in SiC particle size and increases considerably when the residual porosity is less than 1%. Russian translation published in Mekhanika Kompozitnykh Materialov, Vol. 42, No. 3, pp. 401–418, May–June, 2006.     

Boundary-Value Problem of Drainage in a Fresh Groundwater Fringe above Saline Groundwater

A multiparameter boundary-value problem of fresh infiltration water seepage in a drained fringe above quiescent saline water is solved in the direct statement and studied in detail.     

Use of a porous silicon–gold plasmonic nanostructure to enhance serum peptide signals in MALDI-TOF analysis

Small peptides in serum are potential biomarkers for the diagnosis of cancer and other diseases. The identification of peptide biomarkers in human plasma/serum has become an area of high interest in medical research. However, the direct analysis of peptides in serum samples using mass spectrometry is challenging due to the low concentration of peptides and the high abundance of high-molecular-weight proteins in serum, the latter of which causes severe signal suppression. Herein, we reported that porous semiconductor-noble metal hybrid nanostructures can both eliminate the interference from large proteins in serum samples and significantly enhance the matrix-assisted laser desorption/ionization time-of-flight mass spectrometry (MALDI-TOF-MS) yields of peptides captured on the nanostructure. Serum peptide fingerprints with high fidelity can be acquired rapidly, and successful discrimination of colorectal cancer patients based on peptide fingerprints is demonstrated.     

Implementation of ADER scheme for a bore on an unsaturated permeable slope

The paper details the implementation of the Godunov‐type finite volume Arbitrary high order schemes using Derivatives (ADER) scheme for the case of a large source term in the continuity equation of the nonlinear shallow water equations. The particular application is the movement of a bore on a highly permeable slope. The large source term is caused by the infiltration into the initially unsaturated slope material. Infiltration is modelled as vertical downwards piston‐like flow with Forchheimer quadratic parameterisation of the resistance law. The corresponding ODE is solved using the fourth‐order Runge–Kutta method. The surface and subsurface flow models have been tested by comparison with analytical solutions. Example predictions of surface bore propagation and wetting front propagation are presented for a range of slope permeabilities. The effects of permeability on bore run‐up, water depths and velocities are illustrated. The ADER scheme is capable of handling the source term, including the extreme case when this term dominates the volume balance. Copyright © 2011 John Wiley & Sons, Ltd.     

高压熔渗生长法制备金刚石聚晶中碳的转化机制研究

在6 GPa和1500 ℃的压力和温度范围内, 利用高压熔渗生长法制备了纯金刚石聚晶, 深入研究了高温高压下金刚石聚晶生长过程中碳的转化机制. 利用光学显微镜、X-射线衍射、场发射扫描电子显微镜检测, 发现在熔渗过程中金刚石层出现了石墨化现象, 在烧结过程中金刚石颗粒表面形貌发生了变化. 根据实验现象分析, 在制备过程中存在三种碳的转化机制: 1)金属熔渗阶段金刚石颗粒表面石墨化产生石墨; 2)产生的石墨在烧结阶段很快转变为填充空隙的金刚石碳; 3)金刚石直接溶解在金属溶液中, 以金刚石形式在颗粒间析出, 填充空隙. 本文研究碳的转化机制为在高温高压金属溶剂法合成金刚石的条件下(6 GPa和1500 ℃的压力和温度范围内)工业批量化制备无添加剂、无空隙的纯金刚石聚晶提供了重要的理论指导.     

The numerical analysis of water and solute movement in scale heterogeneous profiles

A computer based numerical method is presented for the analysis of water and solute movement in unsaturated heterogeneous porous materials. Such a method is necessary since, for those field studies where solute movement is of concern, the soil profiles under consideration are invariably heterogeneous. The numerical analysis is based on a general one-dimensional finite difference soil water flow model which includes a numerical technique combining the concepts of scale heterogeneity with an interpolative soil water hysteresis model. An explicit finite difference solute movement subroutine is incorporated into the unsaturated flow model to describe the transport of nonreactive solutes. A velocity dependent longitudinal dispersion coefficient is used in the solution of the hydrodynamic dispersion equation. The resulting hysteretic scale heterogeneous solute movement model permits the study of solute dynamics during infiltrating and redistribution in realistically complex spatially varying soil profiles. Results are presented for the leaching of both coarse grading to fine and fine grading to coarse sand profiles. Both vertical and horizontal profiles are studied using either a constant flux or a constant concentration input boundary condition. The four cases studied demonstrate the versatility of the numerical method and emphasise the substantial differences in transport behavior that can arise between heterogeneous and homogeneous profiles.Now with BHP Petroleum Pty. Ltd., GPO Box 1911R, Melbourne, Vic. 3001, Australia.     

Isotopes in groundwater as indicators of climate changes

Isotopes of the water molecule (δ¹⁸O and δ²H) are a well-used tool for investigating groundwater origin and history (i.e. tracing the recharge conditions over time, processes occurring during infiltration of rainwater towards aquifers and those involved in the water-rock interaction, and mixing of different waters).This review covers several large European aquifers (Portugal, France, UK, Switzerland, Germany, Hungary, and Poland), which were investigated in terms of their recharge conditions, and the story of the groundwater at a large scale, involving recent, Holocene and Pleistocene components and their eventual mixing.     

Asymptotic infiltration into a soil which contains cracks or holes but whose surface is otherwise impermeable

An asymptotic, one-dimensional Green-Ampt model is derived for infiltration into a soil whose surface is impermeable except for regularly spaced vertical cracks, and infiltration into a cylindrical soil column whose top surface is also impermeable except for a central hole. The model is valid at times when the wetting front has become horizontal and corresponds to one-dimensional infiltration initiated from a plane lying above or below the soil surface, depending on the crack spacing/depth ratio (or column radius/hole depth ratio). When applicable, asymptotic Green-Ampt solutions are shown to agree well, in selected cases, with corresponding finite difference solutions of the saturated-unsaturated flow equations.     

LSM-infiltrated LSCF cathodes for solid oxide fuel cells

Mixed ionic-electronic conductors in the family of La_xSr_1–xCo_yFe_1–yO_3–δ have been widely studied as cathode materials for solid oxide fuel cells (SOFCs). However, the long-term stability was a concern. Here we report our findings on the effect of a thin film coating of La_0.85Sr_0.15MnO_3–δ (LSM) on the performance of a porous La_0.6Sr_0.4Co_0.2Fe_0.8O_3–δ (LSCF) cathode. When the thicknesses of the LSM coatings are appropriate, an LSM-coated LSCF electrode showed better stability and lower polarization (or higher activity) than the blank LSCF cathode without LSM infiltration. An anode-supported cell with an LSM-infiltrated LSCF cathode demonstrated at 825 °C a peak power density of ～1.07 W/cm², about 24% higher than that of the same cell without LSM infiltration (～0.86 W/cm²). Further, the LSM coating enhanced the stability of the electrode; there was little degradation in performance for the cell with an LSM-infiltrated LSCF cathode during 100 h operation.