真空注入法在功能性食品加工中的试验研究

功能性食品是除具有原有的营养功能外,还具有一种或多种能够提高人的健康状况或防治疾病的靶向功能。真空注入法是一种新型的功能性新鲜果蔬的生产方法,可以在多孔产品中注入任何成分,以调整产品组成。在真空注入过程中,温度、溶液浓度和真空处理时间是影响注入量的重要参数,本文研究了这三个参数对真空注入强化萝卜钙含量的影响。     

Synthesis of cellulose carbamate by supercritical CO2-assisted impregnation: Structure and rheological properties

Cellulose carbamate, an environmentally friendly material presents an interesting alternative to petroleum-based polymers because of its renewable, biodegradable, biocompatible nature and its solubility in conventional solvents. In synthesis process of cellulose carbamate, urea was firstly impregnated into the cellulose pulp by supercritical CO₂(scCO₂), followed by the esterification of cellulose. The structure of cellulose carbamate was characterized by Fourier transform infrared spectroscopy (FTIR), X-ray diffractometry (XRD) and scanning electron microscopy (SEM). The rheological properties of these cellulose carbamates in 9% sodium hydroxide solution were investigated, using a range of the nitrogen content, concentrations and shear rates.     

阴极支撑型固体氧化物燃料电池的制备与测试

采用固相反应法合成A缺位的(La_0.8Sr_0.2)_0.95MnO₃(LSM95)作为阴极材料,Zr_0.9Sc_0.1SO_1.95(SSZ)商业粉体作为电解质材料,溶胶-凝胶法合成的La_0.8Sr_0.2Cr_0.5Mn_0.5O₃-(LSCrM)作为阳极电催化材料,利用流延、共烧结及浸渍法得到结构为LSCrM-CeO₂|SSZ|3YSZ-LSM95的阴极支撑型固体氧化物燃料电池,分别在氢气气氛和甲烷气氛中进行电化学性能测试. 结果表明,浸渍0.11 g·cm ^-2 CeO₂的LSCrM-CeO₂|SSZ|3YSZ-LSM95单电池在以CH₄为燃料时,600、650、700、750和800 ^oC下的功率密度分别为1.68、4.70、12.40、28.08和54.78 mW·cm ^-2,表现出一定的电化学性能和较好的稳定性.     

三组分(NiO、La2O3、SiO2)负载型加氢催化剂中La2O3的作用

用X射线衍射分析、FT-IR、小角X光散射等方法研究了浸渍法制备的NiO/SiO_2和NiO/(La_2O_3+SiO_2)样品中组分之间的相互作用。La_2O_3在SiO_2上可形成近乎密置单层的分散。在负载了La_2O_3的SiO_2上,NiO的分散程度比在SiO_2上有明显提高,也更容易被还原,而且还原后所得金属镍粒子的平均粒度降低,小粒子所占百分比提高。这些结果表明,NiO/(La_2O_3+SiO_2)比NiO/SiO_2样品具有更高的加氢还原硝基普鲁卡因为胺基普鲁卡因的活性,与Ni/(La_2O_3+SiO_2)比Ni/SiO_2活性高的情形相一致。     

Effects of the preparation methods on the properties of Ni-La2O3-SiO2 catalysts for m -dinitrobenzene hydrogenation

Ni-La₂O₃-SiO₂ catalysts were prepared by wetness impregnation and sol-gel method followed by conventional drying and supercritical drying, respectively. Their physico-chemical properties and activity for the hydrogenation of m-dinitrobenzene to m-phenylenediamine were investigated by BET, XRD, TPR, H₂-TPD and activity tests. The results showed that the structural and catalytic properties of the Ni-La₂O₃-SiO₂ catalysts obviously depended on the preparation method and the drying mode. The catalyst prepared by the sol-gel method in combination with conventional drying exhibited the highest catalytic activity among the catalysts tested, attributable to its well-dispersed nickel particles and larger active nickel surface area.     

The preparation of thick-film glass capillary columns

A detailed method for the routine preparation of glass capillary columns is presented. The method consists of coating a glass tube with quartz powder prior to pulling the tube into a capillary. The inner surface of the capillary consists of an even distribution of quartz particles fused to the walls. This surface has been found readily deactivated by standard procedures and ideal for the preparation of thick-film glass capillary columns. The method has been thoroughly tested in two independent laboratories to ensure that the procedures described are reproducible.     

The sintering of silica aerogels studied by thermoporometry

The evolution of the texture of silica aerogels during sintering is studied by thermoporometry for both neutral and base catalysed materials.During the densification the macroporous volume drops and the analysis of the mesopore size distribution evolution shows that the collapse of the smallest mesopores is responsible for the macropore volume transformation. However, corrections of the measured volumes are necessary to characterize the most compliant materials.     

Preparation of Nano-Sized γ-Al2O3 Supported Iron Catalyst for Fischer-Tropsch Synthesis by Solvated Metal Atom Impregnation Methods

Two types of small iron clusters supported on γ-Al2O3-RT(dehydroxylated at room temperature) and γ-Al2O3-800 (dehydroxylated at 800 ℃) were prepared by solvated metal atom impregnation (SMAI) techniques. The iron atom precursor complex, bis(toluene)iron(0) formed in the metal atom reactor, was impregnated into γ-Al2O3 having different concentrations of surface hydroxyl groups to study the effect of surface hydroxylation on the crucial stage of iron cluster formation. Catalysts prepared in this way were characterized by TEM, M(o)ssbauer, and chemisorption measurements, and the results show that higher concentration of surface hydroxyl groups of γ-Al2O3-RT favors the formation of more positively charged supported iron cluster Fen/γ-Al2O3-RT, and the lower concentration of surface hydroxyl groups of γ-Al2O3-800 favors the formation of basically neutral supported iron cluster Fen/γ-Al2O3-800. The measured results also indicate that the higher concentration of surface hydroxyl groups causes the rapid decomposition of precursor complex, bis(toluene)iron(0), and favors the formation of relatively large iron cluster. Consequently, these two types of catalysts show different catalytic properties in Fischer-Tropsch reaction. The catalytic pattern of Fen/γ-Al2O3-RT in F-T reaction is similar to that of the unreduced α-Fe2O3 and that of Fen/γ-Al2O3-800 is similar to that of the reduced α-Fe2O3.     

Dielectric Loss and Electrical Conductivity Behaviors of Epoxy Composites Containing Semiconducting ZnO Varistor Particles

Polymer nanodielectrics render a great material platform for exhibiting the intrinsic nature of incorporated particles, particularly semiconducting types, and their interfaces with the polymer matrix. Incorporating the oxide fillers with higher loading percentages (>40 vol%) encounters particular challenges in terms of dispersion, homogeneous distribution, and porosity from the process. This work investigated the dielectric loss and electrical conduction behaviors of composites containing semiconducting ZnO varistor particles of various concentrations using the epoxy impregnation method. The ZnO varistor particles increased the dielectric permittivity, loss, and electrical conductivity of the epoxy composites into three different regimes (0–50 vol%, 50–70 vol%, 70–100 vol%), particularly under an electric bias field or at higher temperatures. For lower loading fractions below 50 vol%, the dielectric responses are dominated by the insulating epoxy matrix. When loading fractions are between 50 and 70 vol%, the dielectric and electric responses are mostly associated with the semiconducting interfaces of ZnO varistor particles and ZnO–epoxy. At above 70 vol%, the apparent increase in the dielectric loss and conductivity is primarily associated with the conducting ZnO core forming the interconnected channels of electric conduction. The foam-agent-assisted ZnO varistor particle framework appears to be a better way of fabricating composites of filler loading above 80 vol%. A physical model using an equivalent capacitor, diode, and resistor in the epoxy composites was proposed to explain the different property behaviors.     

Removal of Malachite Green Dye from Aqueous Solution by Catalytic Wet Oxidation Technique Using Ni/Kaolin as Catalyst

In this study, natural Algerian kaolin was used as a support and impregnated with nickel at different loading amounts (2 wt.%, 5 wt.%, and 7 wt.%) in order to prepare a supported catalyst. The wet impregnation technique was used in this preparation; nickel oxide (NiO) was the active phase precursor of the catalyst, and the catalysts were designated as follows: 2%, 5%, and 7% Ni/kaolin. These catalysts were put to the test in catalytic wet peroxide oxidation (CWPO) for degrading the organic contaminant malachite green dye (MG). Analytical techniques such as FTIR spectroscopy, X-ray diffraction, BET, and X-fluorescence were used to examine the structure, morphology, and chemical composition of the support and the produced catalysts. Several parameters, including temperature, catalytic dose, metal loading, hydrogen peroxide volume, and kinetic model were systematically investigated. The combination of improved parameters resulted in a significant increase in the catalytic activity, achieving a high removal rate of MG dye of 98.87%.