Advances in rapid and effective break-in/conditioning/recovery of automotive PEMFC stacks

Automotive proton exchange membrane fuel cell stacks need to meet manufacturer specified rated beginning-of-life (BOL) performance before being assembled into vehicles and shipped off to customers. The process of “breaking-in” of a freshly assembled stack is often referred to as “conditioning.” It has become an intensely researched area especially in automotive companies, where imminent commercialization of fuel cell electric vehicles (FCEVs) demands a short, energy- and cost-efficient, and practical conditioning protocol. Significant advances in reducing the conditioning time from 1 to 2 days to as low as 4h or less, in some cases without the use of additional inert gases such as nitrogen, and with minimal use of hydrogen, and specialized test stations will be discussed.     

Numerical study on thermal performance of TiO2, Fe3O4 and NiCr/engine oil in an inclined wavy pip

The essential intention of the existing article is to illustrate the effect of wall properties on flow and thermal behavior, through a sinusoidal inclined wavy pipe. To succeed this phenomena we assume a sinusoidal pipe consist of wavy surface, whose walls traveling down to its borders and located at an inclined position, moreover titanium dioxide (TiO₂), ferrosoferric oxide (Fe₃O₄) and nichrome (80% Ni and 20% Cr) are considered as nano-particles and unused engine oil is assumed as a base fluid. The arising mathematical equations for thermal and flow ratio with wall slip impact are solved by mathematica. Also, evaluate graphically the thermal and flow behavior of nanofluids for multi values of solid volume fractions (η), rigidity parameter (M₁), stiffness parameter (M₂), viscous damping parameter (M₃), Grashof number (G_r), slip parameter (β) and heat generation parameter (H) also discuss the streamlines for different values of solid volume fraction.     

煤直接液化油中混合酚的分离研究

利用分子筛择形特点，对煤直接液化油中的混合酚实施高效分离。本研究选取间甲酚和对甲酚作为分离煤直接液化油馏分段混合酚的模型化合物，采用化学液相沉积法对HZSM-5吸附剂的孔口结构进行改变，分析分子筛硅铝比及颗粒粒径对模型化合物间甲酚和对甲酚吸附分离性能的影响，以获得高性能固相吸附剂，并将其应用于180-190℃馏分段混合酚分离。结果表明，当分子筛硅铝比为25、粒径为3-5 μm时，分子筛的孔口结构调节效果最优；当正硅酸乙酯的最小用量为0.2 mL/g时，固相吸附剂的吸附量为0.03 g/g，对甲酚选择性高于95%。由于外表面沉积物对吸附剂的孔口结构变化，导致对甲酚选择性的提高。进一步采用HZSM-5（1）吸附剂对真实煤直接液化油混合酚的分离中发现，苯酚和对甲酚的选择性均达到100%。     

Morphologically controlled synthesis of 1-dimensional selenium dioxide and study of its application as catalyst for diesel fuel additive

In this research work, selenium dioxide (SeO₂) nanorods have been prepared by a solvothermal method in which a strong reducing agent (NaBH₄) was used to reduce precursor salt into SeO₂ nanorods. X-ray diffraction (XRD) technique was applied to observe the crystal structure which confirmed its tetragonal geometry. Moreover, morphology and particle size were studied by scanning electron microscopy (SEM). SEM fully described the 1-dimensional morphology of SeO₂ nanorods which then arranged themselves to create a 3-dimensional flower-like structure with an average particle size of 50 nm. Also, the catalytic activity of SeO₂ nanorods as diesel-additive was studied by defining different parameters such as fire and flash points, calorific value, cloud and pour points, specific gravity, and kinematic viscosity. Subsequently, SeO₂ nanorods proved to be an excellent diesel additive due to higher total heat content and lower value of kinematic viscosity which enhances the better performance of the diesel engine.     

从废水到新能源:光催化燃料电池的优化与应用

随着经济的飞速发展,社会对能源的需求日益扩大,对工业废水的无害化处理也提出了更高的要求。光催化燃料电池 (photocatalytic fuel cell, PFC) 在燃料电池中引入半导体光催化材料作为电极,实现了有机污染物高效降解和同步对外产电的双重功能,在废水无害化与资源化利用方面具有潜在的应用价值。半导体光催化电极是PFC系统高效运行的核心组件,增强其可见光响应和光生载流子分离是提高PFC性能的关键策略。反应器结构设计和运行参数优化也有利于改善PFC性能。本文从PFC基本原理和应用入手,综述了PFC在环境污染物资源化处理中的研究进展,并详细阐述了提高PFC的污染控制性能和产电效率的优化手段,为进一步设计高效稳定的PFC系统并实现其在水污染控制和清洁能源生产中的应用提供理论指导。     

不同重力环境下辐射加热材料表面着火特性分析

研究外界辐射加热下，不同重力环境中热薄燃料的着火特性．探讨了重力、环境氧浓度、环境压力及外界辐射强度对着火的影响．结果表明，随着重力的变化，存在不同的着火机制．在微重力和在高的环境氧浓度中，材料的着火延迟时间变短．压力减小，着火延迟时间增大．随着辐射强度的增大，着火延迟时间变小．     

High-throughput screening of fuel cell electrocatalysts

The drawbacks of our earlier report of preparing fuel cell catalyst arrays by borohydride reduction of inkjet prepared arrays of metal salts are discussed along with the need for inclusion of state-of-the-art metrics in all array screening. An alternative method for screening of hydrogen/air cathode catalysts, direct methanol fuel cell (DMFC) anode catalysts, and catalyst loading studies is provided. State-of-the-art Johnson Matthey catalysts were used in control experiments to demonstrate the utility of the array fuel cell for high throughput screening of fuel cell catalysts in the 3-4 mg/cm² range. This report lays out hard learned rules for high throughput screening and demonstrates that the array fuel cell can be used for very precise screening of libraries of membrane electrode assembly (MEA) components without the pitfalls discussed in the introduction.     

Optimization of Mass Transfer Processes in the Zone of the Air Electrode of a Fuel Cell with a Solid Polymer Electrolyte

A two-dimensional mathematical model for the transport of reactants in a fuel cell with a solid polymer electrolyte is developed. The model is used for analyzing spatial distributions of the concentration of reactants and current density over the cell. The effect of the catalytic-layer activity, reactant speed, bipolar-plate geometry, thickness and porosity of current collector and/or gas-diffusion sublayer, and the reaction mixture composition on the fuel cell efficiency is estimated theoretically and experimentally.     

“Slow” active control of combustion instabilities by modification of liquid fuel spray properties

This paper describes an experimental investigation of the feasibility of using “slow” active control approaches, which “instantaneously” change liquid fuel spray properties, to suppress combustion instabilities. The objective of this control approach was to break up the feedback between the combustion process heat release and combustor pressure oscillations that drive the instability by changing the characteristics of the combustion process (e.g., the characteristic combustion time). To demonstrate the feasibility of such control, this study used a proprietary fuel injector (Nanomiser^TM), which can vary its fuel spray properties, to investigate the dependence of acoustics–combustion process coupling, i.e., the driving of combustion instabilities, upon the fuel spray properties. This study showed that by changing the spray characteristics it is possible to significantly damp combustion instabilities. Furthermore, using combustion zone chemiluminescence distributions, which were obtained by Abel’s deconvolution synchronized with measured acoustic data, it has been shown that the instabilities were mostly driven midway between the combustor centerline and wall, a short distance downstream from the flame holder, where the mean axial flow velocity is approximately zero in the vortex near the flame holder. The results of this study strongly suggest that a “slow” active control system that employs controllable fuel injectors could be effectively used to prevent the onset of detrimental combustion instabilities.     

新疆野生黑加仑与马林果实的营养成分分析

通过对新疆野生黑加仑和野生马林的脂肪油，8种微量元素，17种氨基酸以及维生素C的含量进行测定得出：黑加仑脂肪油含量为17．9％，马林的脂肪油含量为22．3％，其中，黑加仑脂肪油中，r－亚麻酸的含量为19．02％，而马林中，其含量为9．40％，黑加仑中K，Na,Ca,Cu,Zn,Fe的含量比马林中的含量高，而Mn,Mg元素的含量却比马林含量低；马林的维生素C含量为16．22mg/g，黑加仑的含量为108mg/g，黑加仑的氨基酸的总量为1．63％，马林为1．14％。