Effect of chemical parameters on pyrene degradation in soil in a pulsed discharge plasma system

Degradation of pyrene in soil in a net-to-net pulsed discharge plasma (PDP) system was reviewed. Effect of main chemical parameters, including air flow rate, pyrene concentration, initial pH and soil moisture content on pyrene degradation was examined. The obtained results show that 87.9% of pyrene could be removed under the condition of 60 min reaction; increasing of air flow rate within 1 L min⁻¹ was favorable for degradation; pyrene removal was decreased with the increase of initial pyrene concentration; oxidation of pyrene was more evident in acidic soil; enhancement of soil moisture content has no benefit on pyrene degradation.     

Elongating the area of plasma/fluid interaction of surface nanosecond pulsed discharges

Plasma-assisted flow control is of high industrial interest, but practical applications at full scale require a large surface of interaction. Nanosecond pulsed Dielectric Barrier Discharge (DBD) have demonstrated promising results of flow control, but their interacting region is limited to only a few cm². In this paper, the conditions to extend a surface nanosecond DBD are documented. It is shown that a sliding discharge regime can fully fill an inter-electrode distance of 40 mm. This discharge regime promotes the formation of two hemispheric pressure waves originating from both air-exposed electrodes while an horizontal region of pressure gradient is also observed.     

Polytetrafluoroethylene and metal structure convective-flow CO laser

A convective flow CO laser composed of polytetrafluoroethylene discharge tubes, nickel–chromium steel components, a cupric heat exchanger and other components is described. Operating in liquid nitrogen condition, output power of 60 W has been obtained from a non-selective cavity.     

厚度对非极性聚合物薄膜驻极体电荷储存及电荷动态特性的影响

以Du Pont公司的商用Teflon FEP A型薄膜为例，通过热脉冲技术、等温表面电位衰减测量和开路热刺激放电电流谱分析等实验结果，讨论了经常温和高温电晕充电后样品厚度对薄膜驻极体的沉积电荷密度、薄膜驻极体的内电场、体电导率以及电荷储存稳定性的影响.通过热脉冲技术组合电导率温度曲线的测量，研究了在不同温度条件下样品厚度对沉积电荷层的平均电荷重心移动的影响.结果表明：在充电参数一定的条件下，随着膜厚的降低，储存电荷密度上升，但电荷稳定性有所下降.因此，合理地调控薄膜厚度，可以有效地优化驻极体的电荷储存能 关键词： 厚度 驻极体 电荷储存能力 电荷稳定性     

采用空心阴极放电等离子体化学气相沉积方法制备a-CH薄膜

 研究了不同衬底-阴极距离、直流电压和H₂流量对a-CH薄膜沉积速率的影响。结果表明：衬底-阴极距离必须大于0.5cm，随着该距离的增加，薄膜的沉积速率减少；直流电压达550V时沉积速率最大；随着H2含量的增加，CH₄含量相对减少，沉积速率随之降低。用AFM观察了以该方法制得的448.4nm CH薄膜的表面形貌，表面粗糙度约为10nm。最后测出了不同条件下CH薄膜的UV-VIS谱，由此可以计算得到薄膜的禁带宽度及折射率。     

Maintenance of Soft Calibration Models in the Determination of Zinc,Cadmium, Lead and Copper by Differential Pulse Anodic Stripping Voltammetry

A strategy for constructing a global multivariate calibration model that includes calibration samples measured over time on different days is developed and applied in electroanalysis. Both synthetic and real samples (tap, extracted and river water) are analyzed by differential‐pulse anodic stripping voltammetry, showing the suitability of the global model constructed that provides successful results similar to those of the usual multivariate calibration. In addition the capability of discrimination of this model is evaluated in prediction for the mean of three replicates with estimation of probability of false noncompliance, α, and false compliance, β, being found 3.1, 11.2, 6.7 and 64.7 nM for nominal concentrations of zinc, cadmium, lead and copper of 96.0, 40.4, 37.3 and 328.0 nM respectively when α=β=0.05. It has been proven that the use of the global calibration does not imply a loss of multivariate analytical sensitivity, using this parameter as quality index of the analytical procedure. The viability of using calibration maintenance strategies with electroanalytical techniques is shown, providing a way to save time and experimental effort when these techniques are used in routine analysis.     

Analysis of semiconducting materials by high-resolution radiofrequency glow discharge mass spectrometry

The analytical capabilities of a high-resolution mass spectrometer in combination with a 13.56 MHz glow discharge ion source for the analysis of semiconducting materials (silicon carbide and gallium arsenide) were studied. It was shown that single positively charged ions of sample material have about 10 eV higher average energy than the ions of the discharge and residual gas. Therefore effective energy separation of the ions of analyte from the ions of the discharge and residual gas was achieved by adjusting the ion transfer optics (breadth and position of energy slit), which improves the analytical capabilities of the developed method.Some analytical applications are presented to illustrate the performance of r.f. GDMS for the bulk analysis of semiconducting materials. The results of the trace element analysis of gallium arsenide and silicon carbide samples are compared with data of independent methods (LIMS, ICP-AES, SIMS).Dedicated to Professor Dr. rer. nat. Dr. h.c. Hubertus Nickel on the occasion of his 65th birthdayOn leave from the Institute of Inorganic Chemistry, 630090 Novosibirsk, Russia     

Towards cooling of high-intensity ion beams

Buffer gas beam coolers may become excellent beam preparation devices for high-resolution mass separation. The small beam emittance provided makes efficient isobar resolution a realistic goal. In order to fulfill the needs of future facilities providing high-intensity beams of rare isotopes, it is desirable to increase the beam intensity limit of such devices from typically several tens of nanoamperes to microamperes. This requires the usage of high-voltage radiofrequencies in a low-pressure gas environment. A buffer gas beam cooler, dedicated to this purpose, is under development at the NSCL. The study of voltage breakdowns under such conditions and the design of an electrode system minimizing them is mandatory.      

Preparation and electrical characterization of (PVC + KBrO3) polymer electrolytes for solid state battery applications

This paper presents results of studies on dc electrical conductivity and transference number measurements on potassium bromate (KBrO₃) complexed polyvinyl chloride (PVC) films prepared by solution cast technique. Temperature dependence of dc electrical conductivity and transference number data indicated the dominance of ion type charge transport in these specimens. The magnitude of conductivity increased with increase in concentration of the salt and temperature. Using this (PVC + KBrO₃) electrolyte, solid-state electrochemical cells were fabricated, and their discharge profiles were studied under a constant load of 100 kΩ. Several cell profiles such as open circuit voltage, short circuit current, power density, and energy density associated with these cells were evaluated and were reported. The features of complexation of the electrolytes were studied by X-ray diffraction and Fourier transform infrared spectroscopy. Paper presented at the Third International Conference on Ionic Devices (ICID 2006), Chennai, Tamilnadu, India, Dec. 7–9, 2006     

Chaotic-to-ordered state transition of cathode-sheath instabilities in DC glow discharge plasmas

Transition from chaotic to ordered state has been observed during the initial stage of a discharge in a cylindrical DC glow discharge plasma. Initially it shows a chaotic behavior but increasing the discharge voltage changes the characteristics of the discharge glow and shows a period subtraction of order 7 period → 5 period → 3 period → 1 period, i.e. the system goes to single mode through odd cycle subtraction. On further increasing the discharge voltage, the system goes through period doubling, like 1 period → 2 period → 4 period. On further increasing the voltage, the system goes to stable state through two period subtraction, like 4 period → 2 period → stable.