Direct visualization of the nanoscopic three‐phase structure and stiffness of NBR/PVC blends by AFM nanomechanical mapping

The PeakForce Quantitative Nanomechanical Mapping based on atomic force microscope (AFM) is employed to first visualize and then quantify the elastic properties of a model nitrile rubber/poly(vinyl chloride) (NBR/PVC) blend at the nanoscale. This method allows us to consistently observe the changes in mechanical properties of each phase in polymer blends. Beyond measuring and discriminating elastic modulus and adhesion forces of each phase, we tune the AFM tips and the peak force parameters in order to reliably image samples. In view of viscoelastic difference in each phase, a three‐phase coexistence of an unmixed NBR phase, the mixed phase, and PVC microcrystallites is directly visualized in NBR/PVC blends. The nanomechanical investigation is also capable of recognizing the crosslinked rubber phase in cured rubber. The contribution of the mixed phase was quantified and it was found that the mechanical properties of blends are mainly determined by the homogeneity and stiffness of the mixed phase. This study furthers our understanding the structure–mechanical property relationship of thermoplastic elastomers, which is important for their potential design and applications. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019 , 57, 662–669     

UJ24型电位差计的检修与调节

UJ24型电位差计使用时出现的故障,可以利用数字万用表排查故障,提出排查方案,进行维修与调节,使它尽快恢复到最佳工作状态,这样既节省厂家的维修时间又节省学校的维修费用。     

Setting local rank constraints by orthogonal projections for image resolution analysis: Application to the determination of a low dose pharmaceutical compound

Raman chemical imaging provides chemical and spatial information about pharmaceutical drug product. By using resolution methods on acquired spectra, the objective is to calculate pure spectra and distribution maps of image compounds. With multivariate curve resolution-alternating least squares, constraints are used to improve the performance of the resolution and to decrease the ambiguity linked to the final solution. Non negativity and spatial local rank constraints have been identified as the most powerful constraints to be used.     

Formation of low-temperature deformation-induced segregations of nickel in Fe–Ni-based austenitic alloys

ABSTRACT

The authors present the results of an investigation in Fe–Ni-Cr austenitic alloys of the low-temperature deformation-induced segregations of nickel that form in the micro regions being (i) located close to grain- and subgrain boundaries and (ii) characteristic of the concentration and magnetic inhomogeneities indicated by the appearance of a dark diffraction contrast at the electron diffraction patterns taken from these regions typical (at the same time) of an enhanced value of Curie temperature. The observed effects were connected with the micro distortions caused by the local change of lattice parameter because of an increase in nickel concentration, as well as in the result of a magnetostriction dilatation. Using methods of the X-ray energy dispersive spectroscopy (XEDS) and atomic-probe body-section radiography (tomography – APT) has made it possible to determine the borders of those regions of austenite that were characteristic of an enhanced concentration of nickel in the fields of the localisation of a deformation-induced segregation of nickel in the vicinity of grain (subgrain) boundaries of austenitic alloys of the types Fe–13Cr–30Ni and Fe–37Ni–3Ti.     

Vacuum‐driven fluid manipulation by a piezoelectric diaphragm micropump for microfluidic droplet generation with a rapid system response time

Recently, we developed a convenient microfluidic droplet generation device based on vacuum‐driven fluid manipulation with a piezoelectric diaphragm micropump. In the present study built on our previous work, we investigate the influence of settings applied to the piezoelectric pump, such as peak‐to‐peak drive voltage (V_p‐p) and wave frequency, on droplet generation characteristics. Stepwise adjustments to the drive voltage in ±10‐V_p‐p increments over the range of 200?250 V_p‐p during droplet creation revealed that the droplet generation rate could be reproducibly controlled at a specific drive voltage. The droplet generation rate switched within <0.5 s after the input of a new voltage. Although the droplet generation rate depended on the drive voltage, this setting had almost no influence on droplet size. The frequency over the selected range (50?60 Hz) did not markedly influence the droplet generation rate or droplet size. We show that the current fluid manipulation system can be conveniently used for both droplet generation and for rapid droplet reading, which is required in many microfluidic‐based applications.     

Microstructural stability and age-hardening behavior of Re-added dual two-phase Ni3Al and Ni3V intermetallic alloys

The effect of Re addition on the microstructure and hardening behaviour of the dual two-phase Ni₃Al (L1₂) and Ni₃V (D0₂₂) intermetallic alloy was investigated by scanning electron microscopy, transmission electron microscopy and Vickers hardness test. The two-phase eutectoid microstructure accompanying the Re-rich precipitates were observed in the channel region of the alloys in which Re substituted for Ni but not in those in which Re substituted for Al and V. The concomitant addition of Nb (or Ta) with Re more stabilized the two-phase eutectoid microstructure and consequently more induced the fine precipitates in the channel region. The annealing at temperatures below the eutectoid temperature was necessary to induce the fine precipitates in the channel region and thereby result in the precipitation hardening. The fine precipitation in the channel region and related hardening was attributed to the alloying feature so that Re is soluble in the A1 (fcc) phase at high temperatures and becomes less soluble in the two intermetallic phases decomposed from the A1 phase at low temperatures.     

Preparation and Characterization of Activated Carbon from Microwave and Conventional Heated Almond Shells Using Phosphoric Acid Activation

Activated carbon production from almond shells using phosphoric acid activation agent was achieved by applying both conventional heating and microwave heating in succession. The morphology and surface properties of activated carbon were studied using thermogravimetric and differential gravimetric analysis, Fourier-transform infrared spectroscopy, scanning electron microscopy, and Brunauer–Emmett–Teller analysis. A surface area of 1128 m²/g was achieved by optimizing the microwave power (500?W), microwave application time (15?minutes), conventional heating time (45?minutes), conventional heating temperature (500?°C), and the phosphoric acid:sample ratio (0.7:1). An adsorption capacity of methylene blue of 148?mg/g and an iodine value of 791?mg/g was obtained for the prepared activated carbon.     

基于DIS数字信息化系统对透光物质透光性能的研究

采用DIS数字信息化系统,对不同浓度的蓝墨水溶液在激光光源照射下的透射平均照度及照度分布图像进行实验研究,得到了平均照度值随溶液浓度变化的规律。对不同颜色塑料膜片对白炽灯光源透过照度值及照度分布图像进行实验研究得到及其相关之规律。     

间歇式高速同步相机新型全数字化微机控制系统

本文提出了一种间歇式高速同步相机的全新设计方法，介绍了系统的工作原理，硬件，软件设计以及核心控制算法，最后给出了实际应用结果。     

Heterogeneous photobleaching in confocal microscopy

Photobleaching was studied during recording of confocal scanning laser microscopy. Studies on fluorescent gels of FITC-labeled dextran were used to evaluate differential bleaching along thez-axis. Differential bleaching along the z-axis was observed and it was seen that this was related to the numerical aperture of the objective in use. This points to the conclusion that photon energy flux density is an important parameter in photobleaching. To check if photon energy flux density heterogeneity is affected by local variation in the refractive index of the sample, photobleaching rates were calculated for different fluorescent objects (sections of seeds, animal cells stained with nuclear stains, immunocytochemistry preparations) and a pronounced similarity was found between photobleaching rates and DIC images.