New ligands for the Fe(III)‐mediated reverse atom transfer radical polymerization of methyl methacrylate

A series of (di)picolinic acids and their derivates are investigated as novel complexing tridentate or bidentate ligands in the iron‐mediated reverse atom transfer radical polymerization of methyl methacrylate in N,N‐dimethylformamide at 100 °C with 2,2′‐azobisisobutyrontrile as an initiator. The polymerization rates and polydispersity indices (1.32–1.8) of the resulting polymers are dependent on the structures of the ligands employed. Different iron complexes may be involved in iron‐mediated reverse atom transfer radical polymerization, depending on the type of acid used. ¹H NMR spectroscopy has been used to study the structure of the resulting polymers. Chain‐extension reactions have been performed to further confirm the living nature of this catalytic system. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 2912–2921, 2006     

A novel tridentate nitrogen donor as ligand in copper catalyzed ATRP of methyl methacrylate

A tridentate ligand, BPIEP: 2,6‐bis[1‐(2,6‐diisopropyl phenylimino) ethyl] pyridine, having central pyridine unit and two peripheral imine coordination sites was effectively employed in controlled/“living” radical polymerization of MMA at 90°C in toluene as solvent, Cu^IBr as catalyst, and ethyl‐2‐bromoisobutyrate (EBiB) as initiator resulting in well‐defined polymers with polydispersities M_w/M_n ≤ 1.23. The rate of polymerization follows first‐order kinetics, k_app = 3.4 × 10^?5 s^?1, indicating the presence of low radical concentration ([P*] ≤ 10^?8) throughout the reaction. The polymerization rate attains a maximum at a ligand‐to‐metal ratio of 2:1 in toluene at 90°C. The solvent concentration (v/v, with respect to monomer) has a significant effect on the polymerization kinetics. The polymerization is faster in polar solvents like, diphenylether, and anisole, as compared to toluene. Increasing the monomer concentration in toluene resulted in a better control of polymerization. The molecular weights (M_n,SEC) increased linearly with conversion and were found to be higher than predicted molecular (M_n,Cal). However, the polydispersity remained narrow, i.e., ≤1.23. The initiator efficiency at lower monomer concentration approaches a value of 0.7 in 110 min as compared to 0.5 in 330 min at higher monomer concentration. The aging of the copper salt complexed with BPIEP had a beneficial effect and resulted in polymers with narrow polydispersitities and higher conversion. PMMA obtained at room temperature in toluene (33%, v/v) gave PDI of 1.22 (M_n = 8500) in 48 h whereas, at 50°C the PDI is 1.18 (M_n = 10,300), which is achieved in 23 h. The plot of lnk_app versus 1/T gave an apparent activation energy of polymerization as (ΔE^≠_app) 58.29 KJ/mol and enthalpy of equilibrium (ΔH⁰_eq) to 28.8 KJ/mol. Reverse ATRP of MMA was successfully performed using AIBN in bulk as well as solution. The controlled nature of the polymerization reaction was established through kinetic studies and chain extension experiments. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 4996–5008, 2005     

Living/controlled radical copolymerization of N‐substituted maleimides with styrene in 1‐butyl‐3‐methylimidazolium hexafluorophosphate and anisole

The atom transfer radical copolymerization of N‐substituted maleimides such as N‐phenylmaleimide (PhMI), N‐cyclohexylmaleimide (ChMI), and N‐butylmaleimide (NBMI) with styrene initiated with dendritic polyarylether 2‐bromoisobutyrates in an ionic liquid, 1‐butyl‐3‐methylimidazolium hexafluorophosphate ([bmim][PF₆]), at room temperature and anisole at 110 °C was investigated. The dendritic‐linear block copolymers obtained in ionic liquid possessed well‐defined molecular weight and low polydispersity (1.05 < M_w/M_n < 1.32) and could be used as a macroinitiator for chain‐extension polymerization, suggesting the living nature of the reaction system. The ionic liquids containing catalyst could be recycled in the atom transfer radical polymerization systems without further treatment. Compared with polymerization conducted in anisole, the polymerization in ionic liquid had a stronger tendency for alternation. The tendency for alternation decreased in the order PhMI > NBMI > ChMI in [bmim][PF₆] and PhMI > ChMI > NBMI in anisole. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 2156–2165, 2003     

Photochemical attachment of polymers on planar surfaces with a covalently anchored monolayer of a novel naphthyl ketone photochemical radical generator

A monolayer of covalently anchored, novel, binaphthyl ketone is used as a surface‐confined photochemical radical generator (PRG) for anchoring a variety of polymers to silicon surfaces. The precursor PRG is synthesized by the application of a facile and novel method for the oxidation of sterically hindered benzylic hydrocarbons to carbonyl compounds. Oxidation was carried out with a stoichiometric amount of potassium peroxydisulfate, in the presence of a catalytic amount of copper sulfate in an acetonitrile/water mixture. The PRG synthesized is characterized by ¹H NMR, UV, and Fourier transform infrared (FTIR). The covalently attached monolayers are characterized by X‐ray photoelectron spectroscopy, ellipsometry, and water contact angle measurements. The method developed is applicable to the preparation of a monolayer of a variety of polymers on a wide range of substrates carrying surface hydroxyl groups. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 5413–5423, 2004     

Atom transfer radical polymerization of methyl methacrylate by copper(I)‐pyridine‐2‐carboximidate catalysts

Pyridine‐2‐carboximidates [methyl ( 1a ), ethyl ( 1b ), isopropyl ( 1c ), cyclopentyl ( 1d ), cyclohexyl ( 1e ), n‐octyl ( 1f ), and benzyl ( 1g )] were prepared from the reaction of 2‐cyanopyridine with the corresponding alcohols. Cyclopentyl‐substituted 1d was found to be a highly effective ligand for copper‐catalyzed atom transfer radical polymerization (ATRP) of methyl methacrylate (MMA). For example, the observed rate constant for a CuBr/ 1d catalytic system was found to be nearly twice as high as the cyclohexyl‐substituted CuBr/ 1e catalytic system [k_obs = (1.19 vs 0.56) × 10^?4 s^?1). The effects of the solvents, temperature, catalyst/initiator, and solvent/monomer ratio on the ATRP of MMA were studied systematically for the CuBr/ 1d catalytic system. The optimum condition for the ATRP of MMA was found to be a 1:2:1:400 [CuBr]_o/[ 1d ]_o/[ethyl 2‐bromoisobutyrate]_o/[MMA]_o ratio at 60 °C in veratrole solution, which yielded well‐defined poly(MMA) with a narrow molecular weight distribution of 1.14. The catalytically active copper complex 2d was isolated from the reaction of CuBr with 1d . Narrow molecular weight distributions as low as 1.06 were achieved for the CuBr/ 1d catalytic system by employing 10% of the deactivator CuBr₂. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 2747–2755, 2004     

Soluble,saturated‐red‐light‐emitting poly(p‐phenylenevinylene) containing triphenylamine units and cyano groups

A conjugated poly(p‐CN‐phenylenevinylene) (PCNPV) containing both electron‐donating triphenylamine units and electron‐withdrawing cyano groups was prepared via Knoevenagel condensation in a good yield. Gel permeation chromatography suggested that the soluble polymer had a very high weight‐average molecular weight of 309,000. A bright and saturated red emission was observed under UV excitation in solution and film. Cyclic voltammetry showed that the polymer presented quasi‐reversible oxidation with a relatively low potential because of the triphenylamine unit. A single‐layer indium tin oxide/PCNPV/Mg–Ag device emitted a bright red light (633 nm). © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 3947–3953, 2004     

Selective quenching of tryptophanyl fluorescence in bovine serum albumin by the iodide ion

Modified Stern-Volmer equation is obeyed by bovine serum albumin (BSA)-iodide system showing selective quenching of tryptophanyl fluorescence of BSA. The fraction of accessible protein fluorescence is 0.56 and the effective Stern-Volmer constant is 290 M^-1 at pH 7.4 in 0.005 M phosphate buffer at 25°C. Collisional quenching is operative both in the BSA -I⁻¹ system and the model system, tryptophan-I⁻¹. It is supported by the observed relationship between the ratio of quenching rate constants (k _q ) and diffusion coefficients and alsok _q with bulk viscosity.     

Synthesis,dynamic light scattering,and luminescence properties of copolymers containing iridium(III) bisterpyridine in the side chain

Supramolecular block‐random copolymers containing [Ir(terpy)₂]³⁺ in the side chain were synthesized via postfunctionalization of a P(S‐b‐AC_terpy) block copolymer. Absorbance and emission spectra compared to a model compound show that the polymer backbone has a minor effect on the polymer absorbance but produces a larger shift for the phosphorescence signals to higher wavelength. Dynamic light scattering of the metal complex containing copolymer studied in various solvents showed monomodal aggregation with decreasing aggregate size as the solvent dielectric constant increased. The copolymer precursor P(S‐b‐AC_terpy) shows multimodal aggregation in different solvents with the major population consisting of single chains. This difference in behavior between the two polymers is attributed to the electrolytic nature of the complex and the amphiphilicity induced by the charged metal complex. Supramolecular copolymers like these will continue to have interesting self‐organizational properties and may find applications in multicomponent systems for photoinduced charge separation processes. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 1109–1121, 2007     

Diblock copolymers based on allyl methacrylate: Synthesis,characterization, and chemical modification

Different diblock copolymers constituted by one segment of a monomer supporting a reactive functional group, like allyl methacrylate (AMA), were synthesized by atom transfer radical polymerization (ATRP). Bromo‐terminated polymers, like polystyrene (PS), poly(methyl methacrylate) (PMMA), and poly(butyl acrylate) (PBA) were employed as macroinitiators to form the other blocks. Copolymerizations were carried out using copper chloride with N,N,N′,N″,N″‐pentamethyldiethylenetriamine (PMDETA) as the catalyst system in benzonitrile solution at 70 °C. At the early stage, the ATRP copolymerizations yielded well‐defined linear block copolymers. However, with the polymerization progress a change in the macromolecular architecture takes place due to the secondary reactions caused by the allylic groups, passing to a branched and/or star‐shaped structure until finally yielding gel at monomer conversion around 40% or higher. The block copolymers were characterized by means of size exclusion chromatography (SEC), ¹H NMR spectroscopy, and differential scanning calorimetry (DSC). In addition, one of these copolymers, specifically P(BA‐b‐AMA), was satisfactorily modified through osmylation reaction to obtain the subsequent amphiphilic diblock copolymer of P(BA‐b‐DHPMA), where DHPMA is 2,3‐dihydroxypropyl methacrylate; demonstrating the feasibility of side‐chain modification of the functional obtained copolymers. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 3538–3549, 2007     

Surface polarity of cellulose derivates observed by coumarin 151 and 153 as solvatochromic and fluorochromic probes

Solvent‐dependent ultraviolet–visible (UV–vis) absorption and Stokes shifts including strong hydrogen‐bond‐donating (HBD) solvents such as 2,2,2‐trifluoroethanol and 1,1,1,3,3,3‐hexafluoro‐2‐propanol of two coumarine dyes (Co 151 and Co 153) were analyzed with multiple‐square analyses of linear solvation energy relationships and the Kamlet–Taft solvent parameter set to α (HBD capacity), β (hydrogen‐bond‐accepting capacity), and π* (dipolarity/polarizability). The UV–vis absorption and emission spectra of Co 151 and Co 153 were measured when adsorbed on various polysaccharides such as different cellulose batches, carboxymethylcelluloses with different degrees of substitution, and chitine. As a result of this evaluation, Co 153 is recommended as an alternative UV–vis probe for evaluating the dipolarity/polarizability of cellulose and cellulose derivates. Multiple adsorption of Co 153 on Linters cellulose took place indicating a wide‐surface polarity distribution, which makes the determination of a rigid polarity parameter questionable. Thus, fluorescence measurements of adsorbed Co 153 are suitable to detect inhomogenities on a surface but not for the determination of empirical polarity parameters. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1210–1218, 2003