Carbon-13 NMR evidence for cocrystallization of cellulose as a mechanism for hornification of bleached kraft pulp

Solid-state ¹³C NMR spectroscopy was used to characterize a bleached softwood kraft pulp in the never-dried state and after cycles of drying and remoistening. Changes in NMR signal strengths indicated that growth of crystalline domains involved cocrystallization rather than accretion of cellulose from noncrystalline domains. A cluster of C-4 signals at 89.4 ppm, assigned to the interiors of crystalline domains, grew at the expense of C-4 signals at 84.0 and 84.9 ppm, assigned to the well-ordered surfaces of crystalline domains. Irreversible changes were not detected until the moisture content dropped below 18%. They were enhanced by a second drying/remoistening cycle, but showed little further change on subsequent cycles. The necessary conditions resembled those reported for hornification, suggesting that cocrystallization might provide a mechanism for hornification.     

Chromatographic characterization of thermally upgraded products from alternative fuels

An overview is presented of the analytical approaches developed by our research group over the last ten years for analysis of alternative fuel, both biomass and fossil. The alternative fuels are analyzed successively by PLC-8 (preparative liquid chromatography–group-type) fractionation and high resolution gas chromatography. Some of the possibilities for fractionation and characterization of alternative fuels are herein exemplified with sugar cane bagasse pyrolysis products.     

A procedure for measuring the flexibility of single wood-pulp fibres

A way of determining the flexibility of wood-pulp fibres is developed, which involves i) a precise measurement of the topology of single-fibres by using a confocal laser scanning microscope and ii) the measurement of the elastic modulus of the fibres by using a single-fibre fatigue cell. Reported in this paper are the initial results of tests carried out on black spruce fibres, which have been subjected to three different levels of mechanical refining energy, namely ∼1100, 2300, and 3500 kWh/t. It is found that the fibre flexibility rises significantly between the first and second energy levels, but it does not change to the same degree between the second and third ones. The described procedure of measuring the flexibility of fibres may be used to establish the appropriate refiner energy necessary for the production of a specific grade of paper. Russian translation published in Mekhanika Kompozitnykh Materialov, Vol. 42, No. 1, pp. 115–128, January–February, 2006.     

The Influence of Cobalt (II) in Carboxymethyl Cellulose Processing

Controlling the reduction in molecular weight of the cellulose chains is essential in the production of carboxymethyl cellulose (CMC). Such a reduction can be achieved by the addition of cobalt during the process of cobalt(II) ions, which act as a catalyst for oxidative cleavage, and the influence thereof has been studied under a variety of conditions. This study has resulted in a model that summarises the effects of the added amount of cobalt, the time for the cobalt reaction, the temperature in the mercerisation stage of the CMC-manufacturing process and finally the effect of the temperature in the etherification stage. It is shown that it is important for cobalt to be present during the mercerisation stage in order to achieve the desired viscosity.     

Ethanol/water pulp enzymatic pretreatment: Chemical and FTIR-PCA analyses

Pulps obtained from ethanol/water cooking of sugarcane bagasse were treated at different times using xylanase enzyme obtained from Thermomyces lanuginosus IOC-4145 or commercially (Cartazyme HS, Sandoz Products Ltd.). The enzyme dosage was 18 IU per g of dry pulp and the time varied from 4 h to 12 h. When xylanase from T. lanuginosus was used, the kappa number and viscosity improved independently of the processing time used (4 h, 8 h, and 12 h). After chemical evaluation, the obtained pulps were classified using Fourier Transformed Infra-Red Spectroscopy and Principal Component Analysis. The results showed that the first three principal components explained more than 90 % of the total variance of the pulp spectra.     

Microgels and ionic associations in solutions of cellulose diacetate

Solutions of cellulose diacetate (CDA) from two sources (cotton linters and wood pulp Floranier) were analysed in various solvents by size exclusion chromatography (SEC). Without special precautions, the SEC chromatograms presented three peaks — or prehumps — before the main polymer peak. The first prehump which could be eliminated by ultracentrifugation corresponded to microgels whose sugar composition was determined. These microgels were also investigated by electron microscopy, X-ray and electron diffraction analysis. They corresponded mainly to cellulose triacetate (CTA-II) in the case of CDA from cotton linters and a mixture of CTA-II and xylan diacetate (XDA) in the case of CDA from the wood pulp Floranier. The second and third prehumps could be attributed to ionic effects corresponding to the association of remaining sulfate groups on the CDA molecules with residual calcium. It was found that these ionic effects could be eliminated by the addition of LiBr or LiCl to the elution solvents. This led to chromatograms devoid of prehumps.Presented in part at the Cellulose '91 meeting in New Orleans.     

The characteristic fragment ions and visualization of cationic starches on pulp fiber using ToF‐SIMS

Time‐of‐flight secondary ion mass spectrometry (ToF‐SIMS) was used to investigate the distribution of cationic starch on pulp fiber. To identify the characteristic fragment ions of the cationic starches, deuterium‐labeled cationic starches were prepared and analyzed using ToF‐SIMS. The starch 2‐hydroxypropyltrimethylammonium chloride derivative generated characteristic fragments at m/z 58 and 59, which were identified as [H₂C?N(CH₃)₂]⁺ and [N(CH₃)₃]^+·, respectively. The fragmentation patterns were also suggested. From the imaging analysis, the adsorption of the cationic starch on fibers was uneven on individual fibers, as well as between fibers. This may have been on account of fiber morphology and structure. On examining scanning electron microscope (SEM) images, the quaternary ammonium starch derivative (QS) did not penetrate the fiber. No migration of cationic starch was observed under various drying conditions. Copyright © 2007 John Wiley & Sons, Ltd.     

Characterization of Carbohydrates in Paper and Paper Pulps Using Anion Exchange Chromatography and Principal Component Analysis

In the course of this investigation, a method for the characterization and differentiation of paper pulps was developed. After hydrolyzation of the papers and the respective raw pulps with trifluoroacetic acid, the hydrolyzates were analyzed with respect to their carbohydrate composition using ion exchange chromatography. The variations in carbohydrate composition mainly arise from the various hemicelluloses of the papers and pulps. The chromatographic results were then further processed using principal component analysis which allows correlating the various papers to different pulp materials.     

Xylanolytic enzyme production by anAspergillus niger isolate

Production of xylanolytic enzymes by anAspergillus niger CCMI 850 isolate was investigated in batch cultures. The effect of the composition of a fermentation medium that did not include chemical inducers, on β-xylanase, β-xylosidase, α-l-arabinofuranosidase, and total cellulase activity was studied. With 4% xylan as the carbon source, about 65 U/mL of β-xylanase was obtained, whereas the total cellulase activity was undetectable, under the specified conditions. This β-xylanase activity represents the highest reported for a wild-type strain ofA. niger. The effect of pH and temperature on the activity of β-xylanase was studied. Partial characterization of the β-xylanase showed that with insoluble birchwood as substrate theK _m andV _max were 0.3 mM and 19 μmol/min, respectively. Aspects of using the crude β-xylanase preparation for applications in the pulp and paper industry were discussed.     

Characterization of the supermolecular structure of cellulose in wood pulp fibres

The hierarchic organization of cellulose fibrils (microfibrils) was investigated in holocellulose, sulphite pulp and kraft pulp using TEM, XRD, ED and FTIR. There were remarkable differences in both the fibril structure and fibril aggregation between the samples. TEM observations revealed more intimately associated fibrils in the kraft pulp compared to the sulphite pulp and the holocellulose, results in agreement with previous CP/MAS ¹³C-NMR data [Hult E.-L. et al. (2002) Holzforschung 56: 231–234]. Furthermore, the cellulose crystallinity was higher in the kraft pulp sample. With respect to the cellulose I and I allomorphs, these samples were controversial when different analytical techniques were applied. Due to the small fibril size and the low degree of order of cellulose in these samples, the concept of crystalline triclinic and monoclinic components as determined by diffraction analysis may not be adequate. Instead the fibril can be regarded to have different degrees of lateral order (including paracrystalline ordering) that can be reoriented to I type conformation and packing upon pulping.