二次阳极氧化方法制备有序多孔氧化铝膜

通过二次阳极氧化方法制备多孔氧化铝膜与一次阳极氧化方法制备多孔氧化铝膜孔排布规律性的对比 ,结果发现 ,二次阳极氧化方法制取的多孔氧化铝膜孔排布规律性明显好于一次阳极氧化法制取的多孔膜 .在几个微米范围内 ,孔呈理想的六角排布 .去除一次阳极氧化膜后 ,二次阳极氧化得以在更良好的表面进行 ,制取的氧化铝膜孔规律性和有序度更高 .有序区域的尺寸与晶粒内的亚晶大小有一定关系     

TiO2一维纳米材料及其纳米结构的合成

本文对合成TiO₂一维纳米材料及其有序纳米阵列的阳极氧化法、模板法以及水热法进行了全面而系统的评述，着重介绍了它们的最新研究进展。阳极氧化法能制备牢固负载于基体上的TiO₂纳米管阵列，这有助于构筑TiO₂纳米结构及其在纳米器件上的应用；与多种制备技术如溶胶－凝胶工艺、电化学沉积以及原子层沉积等相结合，模板法可以合成出多种形貌的TiO₂纳米材料如纳米管、纳米线和纳米棒，并可以通过改变所用模板的微观尺寸来调控TiO₂一维纳米材料及其有序阵列的微结构参数；水热合成法可以制备出直径小且比表面积大的TiO2纳米管粉末。但从目前看来，该法还不能制备出牢固负载于基体上的有序纳米阵列。文章最后指出了TiO₂一维纳米材料及其有序纳米阵列合成中存在的问题及今后发展方向。     

纳米多孔双金属氧化物在镍钛合金纤维上的原位生长及其对多环芳烃的选择性固相微萃取

采用阳极氧化法在镍钛合金(NiTi)纤维上原位生长了双金属氧化物纳米孔(NiTiONPs)涂层,通过扫描电镜(SEM)和能谱(EDS)考察了电解质组成和电压对形貌的影响。将NiTiONPs涂层的NiTi纤维与高效液相色谱-紫外检测器联用,研究了4种典型芳香分析物的萃取性能。结果表明,富含TiO2的NiTiONPs涂层对多环芳烃(PAHs)具有良好的萃取效率,尤其对苯并[a]芘的萃取选择性优于市售聚二甲基硅氧烷纤维和聚丙烯酸酯纤维。在优化条件下,PAHs的线性范围为0.05~200μg/L,相关系数均大于0.999,检出限为0.012~0.134μg/L。对单支纤维日内和日间分析的相对标准偏差(RSDs)分别为4.0%~5.5%和6.0%~6.8%,使用分批组装的5支纤维分析的RSDs为6.4%~7.6%。实际水样分析的加标回收率为84.5%~111.5%。所制备NiTi纤维至少可重复使用250次以上,重现性好。     

ZnO纳米线的电化学制备研究

High-quality ZnO nanowires have been synthesized at relatively low temperature via one-step electrochemical anodization technique. In this method, Zn sheet acted as the anode and Pb sheet served as the counter electrode, and the complex solution of HF-C₂H₅OH-H₂O was used as electrolyte. ZnO nanowires were characterized by Field Emission Scanning Electron Microscopy (FE-SEM), Transmission Electron Microscopy (TEM) and Selected Area Electron Diffraction (SAED) and X-ray Diffraction (XRD). The results show that the nanowires were wurtzite crystalline ZnO, and the ZnO nanowires with the diameters of 70 nm and 30～40 nm were obtained by adjusting preparation conditions, respectively.     

Activation of α-Fe2O3 for Photoelectrochemical Water Splitting Strongly Enhanced by Low Temperature Annealing in Low Oxygen Containing Ambient

Photoelectrochemical (PEC) water splitting is a promising method for the conversion of solar energy into chemical energy stored in the form of hydrogen. Nanostructured hematite (α-Fe₂O₃) is one of the most attractive materials for a highly efficient charge carrier generation and collection due to its large specific surface area and the short minority carrier diffusion length. In the present work, the PEC water splitting performance of nanostructured α-Fe₂O₃ is investigated which was prepared by anodization followed by annealing in a low oxygen ambient (0.03 % O₂ in Ar). It was found that low oxygen annealing can activate a significant PEC response of α-Fe₂O₃ even at a low temperature of 400 °C and provide an excellent PEC performance compared with classic air annealing. The photocurrent of the α-Fe₂O₃ annealed in the low oxygen at 1.5 V vs. RHE results as 0.5 mA cm⁻², being 20 times higher than that of annealing in air. The obtained results show that the α-Fe₂O₃ annealed in low oxygen contains beneficial defects and promotes the transport of holes; it can be attributed to the improvement of conductivity due to the introduction of suitable oxygen vacancies in the α-Fe₂O₃. Additionally, we demonstrate the photocurrent of α-Fe₂O₃ annealed in low oxygen ambient can be further enhanced by Zn-Co LDH, which is a co-catalyst of oxygen evolution reaction. This indicates low oxygen annealing generates a promising method to obtain an excellent PEC water splitting performance from α-Fe₂O₃ photoanodes.     

Slow-rise and fast-drop current feature of ultraviolet response spectra for ZnO-nanowire film modulated by water molecules

This study describes the fabrication of ZnO-nanowire films by electro-chemical anodization of Zn foil.The ZnO films are characterized by field emission scanning electron microscopy,X-ray diffraction patterns,and transmission electron microscopy,respectively.The ultraviolet(UV) photo-response properties of the surface-contacted ZnO film are studied through the current evolution processes under different relative humidities.Unlike the usually observed current spectra of the ZnO films,the drop time is shorter than the rise time.The photo-conductivity gain G and the response time τ are both increased with the increase of the applied bias.The photo-conductivity gain G is lowered with the increase of the environmental humidity,while the response time τ is increased.These results can be explained by considering three different surface processes:1) the electron-hole(e-p) pair generation by the UV light illumination,2) the following surface O2-species desorption,and 3) the photo-catalytic hydrolysis of water molecules adsorbed on the ZnO surface.The slow-rise and fast-drop current feature is suggested to originate from the sponge-like structure of the ZnO nanowires.     

Electrochemical behavior in simulated body fluid of TiO2 nanotubes on TiAlNb alloy elaborated in various anodizing electrolyte

The present study is focused on tailoring the morphology of TiO₂ nanotubes obtained on Ti6Al7Nb alloy and evaluating their electrochemical behavior in simulated body fluid. The presence of the α and β phases on the Ti6Al7Nb alloy leads to a two‐scale organization of the nanotubes on the samples – which in turn affects the electrochemical stability. Furthermore, five different types of TiO₂ nanotubes were obtained in various electrolytes (e.g. Generation I, a mixture of Generation II and Generation III, Generation III). Electrochemical behavior analysis of all obtained nanotubes morphologies was composed of Tafel plots, cyclic voltammetry and electrochemical impedance spectroscopy and was correlated with morphology data obtained from SEM (nanotubes diameters from top‐view and nanotube length from cross‐section view). The electrochemical results showed that morphological modifications of the Ti6Al7Nb alloy's surface by electrochemical anodizing have induced changes to the electrochemical behavior of the material, evident in the corrosion rates. Copyright © 2014 John Wiley & Sons, Ltd.     

纳米多孔阳极氧化铁膜的形成及其形貌演变

阳极氧化法制备具有纳米多孔结构的阳极氧化铁膜因其潜在的应用价值而倍受关注。然而,在阳极氧化过程中多孔结构的形成机制至今尚不清楚。本文结合电流密度-电位响应（I-V曲线）及法拉第定律的推导,分析了形成纳米多孔阳极氧化铁膜的过程中阳极电流的组成。结果表明,离子电流（导致离子迁移形成氧化物）和电子电流（导致析出氧气）共同组成阳极电流,并且纳米多孔阳极氧化铁膜的形成与两种电流的占比相关。分段式氧化物之间的空腔以及在阳极氧化初期纳米孔道上覆盖的致密膜,表明氧气泡可能是从氧化膜内部析出。此时,阳离子和阴离子绕过作为模具的氧气泡实现传质,最终导致纳米多孔结构的形成。此外,在阳极氧化铁膜形貌演变过程中,氧气泡不断向外溢出会使表面氧化物被冲破,导致表面孔径不断增大。     

Development of Magnesium Anode-Based Transient Primary Batteries

Biodegradable primary batteries, also known as transient batteries, are essential to realize autonomous biodegradable electronic devices with high performance and advanced functionality. In this work, magnesium, copper, iron, and zinc – metals that exist as trace elements in the human body – were tested as materials for biomedical transient electronic devices. Different full cell combinations of Mg and X (where X = Cu, Fe, and Zn and the anodized form of the metals) with phosphate buffered saline (PBS) as electrolyte were studied. To form the cathodes, metal foils were anodized galvanostatically at a current density of 2.0 mA cm⁻² for 30 mins. Electrochemical measurements were then conducted for each electrode combination to evaluate full cell battery performance. Results showed that the Mg−Cu_anodized chemistry has the highest power density at 0.99 mW/cm². Nominal operating voltages of 1.26 V for the first 0.50 h and 0.63 V for the next 3.7 h were observed for Mg−Cu_anodized which was discharged at a current density of 0.70 mA cm⁻². Among the materials tested, Mg−Cu_anodized exhibited the best discharge performance with an average specific capacity of 2.94 mAh cm⁻², which is comparable to previous reports on transient batteries.