Effect of temperature on the luminescence processes of SrAl2O4:Eu

The UV excited and persistent luminescence properties as well as thermoluminescence (TL) of Eu²⁺ doped strontium aluminates, SrAl₂O₄:Eu²⁺ were studied at different temperatures. Two luminescence bands peaking at 445 and 520 nm were observed at 20 K but only the latter at 295 K. Both Sr-sites in the lattice are thus occupied by Eu²⁺ but at room temperature efficient energy transfer occurs between the two sites. The UV excited and persistent luminescence spectra were similar at 295 K but the excitation spectra were different. Thus the luminescent centre is the same in both phenomena but excitation processes are different. Two TL peaks were observed between 50 and 250 °C in the glow curve. Multiple traps were, however, observed by preheating and initial rise methods. With longer delay times only the high temperature TL peak was observed. The persistent luminescence is mainly due to slow fading of the low temperature TL peak but the step-wise feeding process from high temperature traps is also probable.     

“J—646”新型光学光敏胶胶合工艺简介

“J—646”光敏胶具有透光率好,收缩率小,粘接强度适中,耐老化,毒性小和成本低廉等特点。本文简要介绍了该胶的胶合工艺。     

Self-organized ZnAl2O4 nanostructures grown on -sapphire

Self-organized ZnAl₂O₄ nanostructures with the appearance (in SEM) of high aspect ratio horizontal nanowires are grown on uncatalysed c-sapphire by vapour phase transport. The nanostructures grow as three equivalent crystallographic variants on c-sapphire. Raman and cathodoluminescence spectroscopy confirm that the nanostructures are not ZnO and TEM shows that they are the cubic spinel, zinc aluminate, ZnAl₂O₄, formed by the reaction of Zn and O with the sapphire substrate.     

Application of heat flow calorimetry to the study of oilwell cements

The majority of previous studies of the hydration of cements using heat flow calorimetry have been carried out isothermally. However, with oilwell cements the slurry is mixed on the surface at ambient temperature and then gradually increases in temperature as it is pumped down the well. A Setaram C-80 calorimeter has been used to simulate the temperature ramp in API oilwell cement test schedules. This approach has enabled cementing reactions to be studied for the first time under conditions approaching those encountered in the field, and has shown that the results obtained from isothermal experiments may be misleading.The permission of the British Petroleum Company PLC to publish this paper is gratefully acknowledged.     

Eu,Dy共掺杂SrAl2O4长余辉材料制备新工艺

活化Al-Sr合金粉末水解制备SrAl₂O₄长余辉材料的前驱体,并采用高温固相反应法制备出Eu,Dy共掺杂的SrAl₂O₄长余辉材料,对其微观结构和发光特性进行了研究。实验结果表明:前驱体中Al、Sr元素在微观状态下分布均匀,所制成的长余辉发光材料的发射主峰位于520nm附近,为典型的Eu²⁺离子4f5d-4f的特征发射,初始亮度达到18cd/m²,余辉时间长达46h。     

β沸石的铝化

β沸石自1988年结构被确定以来受到普遍重视,由干结构上的特殊性,G沸石既具有较强酸性又具有明显的碱性［‘,‘］．但q佛石的高硅铝比使其在化学组成上对碱性的贡献甚微,如果能降低其硅铝比,则有可能获得具有较强碱性的佛石分子筛．直接合成的o佛石,硅铝比一般在10以上．     

Synthesis of amino acid-containing polyacids and their application in self-cured glass-ionomer cement

Six methacrylate or acrylate derivatives of natural amino acids were synthesized and characterized. Based upon these monomers, six terpolymers [poly(acrylic) acid-co-itaconic acid-co-amino acid] were prepared and characterized. The synthesized polymers were used to formulate glass-ionomer cements (GICs) using Fuji II glass filler. The effects of the molecular weight (MW) and powder/liquid (P/L) ratio were evaluated. Scanning electron microscopy (SEM) was used to examine the fracture surfaces of the selected cement specimens. Results show that all the amino acid modified GICs exhibited higher compressive strengths (CS, 193-236 MPa) and much higher flexural strengths (FS, 55-71 MPa) as compared to commercial Fuji II GIC (191 in CS and 16 in FS). Both MW and P/L ratio affected the strength of the formed cement. It was important to find the optimal MW and P/L ratio to obtain the highest FS. In this study, optimized MW (number average) of the polyacids and P/L ratio were around 50,000 and 2.7/1, respectively. The microstructures of the fracture surfaces helped to explain the strength differences among the materials tested in the study. SEM analysis suggests that more integrated microstructures and fewer defects can lead to higher FS.     

Specific surface of two hydrated cements differing in strength

Specific surface, S, of CSH-gel particles of disordered layered structure, was studied by water sorption/retention in two cement pastes differing in strength, i.e. C-33 (weaker) and C-43 (stronger), w/c=0.4. Hydration time in liquid phase was t _h=1 and 6 months, followed by hydration in water vapour either on increasing stepwise the relative humidity, RH=0.5→0.95→1.0 (WS) or on its lowering in an inverse order (WR). Specific surface was estimated from evaporable (sorbed) water content, EV (110°C), assuming a bi- and three-molecular sorbed water layer at RH=0.5 or 0.95, respectively (WS). On WR it was three- and three- to four-molecular (50 to 75%), respectively, causing a hysteresis of sorption isotherm. At RH=0.5 the S increased with cement strength from 146 m² g^-1 (C-33, 1 m) to 166 m² g^-1 (C-43, 1 m) and with hydration time to 163 (C-33, 6 m) and to 204 m² g^-1 (C-43, 6 m). At RH=1.0 (and 0.95), higher S-value were measured but these differences were smaller: S amounted to 190-200 m² g^-1 in C-33 (1 and 6 m) and 198-210 m² g-1 in C-43 (1 and 6 m). Thus no collapse occurred on air drying of paste C-43 (6 m). This revised version was published online in July 2006 with corrections to the Cover Date.     

In situ neutron powder diffraction investigation of the hydration of tricalcium aluminate in the presence of gypsum

The hydration of a 1:3 molar ratio of tricalcium aluminate, Ca₃Al₂O₆, to gypsum, CaSO₄·2D₂O, was investigated at temperatures of 25, 50, and 80 °C using time-of-flight powder neutron diffraction combined with multiphase Rietveld structural refinement. It was shown that ettringite, Ca₆[Al(OD)₆]₂(SO₄)₃·∼26D₂O, was the first and only hydration product of the system, in contrast to a prior investigation which suggested the occurrence of a precursor phase prior to the formation of ettringite. Kinetics data showed that the hydration reaction is very sensitive to temperature: hydration at 25 °C was characterized by a single kinetic regime while hydration at higher temperatures consisted of two distinct kinetic regimes. The presence of two kinetic regimes was attributed to a change in either the dimensionality of the growth process or a change in the rate controlling mechanism in the hydration reaction.     

Crystal structure of hexagonal SrAl2O4 at 1073 K

The crystal structure of SrAl₂O₄ at 1073 K was determined from conventional X-ray powder diffraction data using direct methods, and it was further refined by the Rietveld method. The structure was hexagonal (space group P6₃, Z=6) with a=0.89260(3) nm, c=0.84985(2) nm and V=0.58639(3) nm³. Final reliability indices were R_wp=7.87%, R_p=5.87% and R_B=4.19%. The [AlO₄] tetrahedra are linked to form trigonally distorted rings and they are joined in layers. These layers are stacked with a two-layer repeat and connected by the tetrahedral apices. All of the Sr atoms occupy the centers of the rings when viewed along the c-axis. The structure is described as a stuffed derivative of tridymite.