Strength of cylinder joint adhesively bonded by coupling

Summary A method of joining two metal cylindrical shafts with adhesive coupling is proposed. Two cylindrical shafts with the same diameter are connected by bonding through a cylindrical coupling with epoxy resin. The strength of the shaft joint under tensile loading and torsional loading is investigated analytically and experimentally. The stress and strain distributions of the shaft joint is analyzed by the finite element method. The analyzed strain distributions in the joint are compared with experimental values. The joint strength is predicted by applying the strength laws of shafts, coupling, adhesive layer and adhesive interface between shaft and adhesive coupling. The effects of the coupling dimension on the joint strength are examined. It is shown that the adhesive shaft joint can transfer the load by which the cylindrical shafts are plastically deformed.This paper was refined by the author, K. Ikegami, during statying at Technische Universität München under the support of Deutscher Akademischer Austauschdients. The author is grateful to Professor Lippmann of Technische Universität München who is the host professor of the support.     

Acrylic acid level and adhesive performance and peel master‐curves of acrylic pressure‐sensitive adhesives

Three series of pressure‐sensitive adhesives were prepared with constant glass‐transition temperature, using emulsion polymerization. The monomers chosen were butyl acrylate, 2‐ethylhexyl acrylate (EHA), methyl methacrylate (MMA), and acrylic acid (AA). Within each polymer series, the proportion of AA monomer was held constant for each polymer preparation but acrylic ester monomer levels were varied. Adhesion performance was assessed by measurement of loop tack, static shear resistance, and through the construction of peel master‐curves. Peel master‐curves were generated through peel tests conducted over a range of temperatures and peel rates and through application of the time–temperature superposition principle. Bulk effects dominated by polymer zero shear viscosity change as AA and EHA levels were varied were attributed to the observed effect on static shear resistance and the horizontal displacements of peel master‐curves. Static shear resistance was found to strongly correlate with log(a_C), a parameter introduced to horizontally shift peel master‐curves to form a superposed, “super master‐curve”. An interfacial interaction was proposed to account for deviations observed when loop tack was correlated with log(a_C). Surface rearrangements via hydrogen bonding with the test substrate were suggested as responsible for the interfacial interaction. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 1237–1252, 2006     

共聚酯型热熔粘结纤维结晶结构及其熔融行为

采用DSC与WAXD相结合的方法研究了两个系列的无规嵌段共聚酯型热熔粘结纤维的结晶结构并探讨了系列样品的熔融行为.实验表明,以最低熔融温度为界,可将样品分为两组,每组只含一种可结晶单元的结晶.其结构与物理机械性质随该可结晶单元的加入量而有规律的变化.纤维的粘结性能则取决于非晶区结构,非晶区分子链柔性增加,会明显改善粘结效果.     

Development in the area of UV-crosslinkable solvent-based pressure-sensitive adhesives with excellent shrinkage resistance

Solvent-based UV-crosslinkable pressure-sensitive adhesives (PSA) present a new class of products that offers the potential to produce a novel generation of ultraviolet cured self-adhesive products with excellent shrinkage resistance. A variety of solvent-based pressure-sensitive adhesives were prepared by synthesis in ethyl acetate with solid content on 50 wt.% with 2-ethylhexyl acrylate, methyl acrylate, acrylic acid, N-vinyl caprolactam and unsaturated photoinitiators: 4-acryloyloxy benzophenone, allyl benzoine and phenyl-(1-acryloyloxy)-cyclohexyl ketone. The main emphasis is given to the influence of viscosity and molecular mass of synthesized adhesive on their shrinkage. Further trials show the effect of the UV-crosslinking process with UV-lamp and comparison with acrylics PSA crosslinked with metal chelates aluminium acetylacetonate and titanium acetylacetonate on shrinkage. Further examinations describe the influence of various factors such as UV exposure time and UV dose on very relevant PSA performance such as shrinkage on coated PVC carrier.     

Effect of Al2O3 nanoparticles on the steel-glass/epoxy composite joint bonded by a two-component structural acrylic adhesive

This paper reports a study on the effect of Al₂O₃ nanoparticles on the adhesion strength of steel-glass/epoxy composite joints bonded by a two-component structural acrylic adhesive. The addition of Al₂O₃ nanoparticles to the two-component acrylic adhesive led to a remarkable enhancement in the shear and tensile strength of the composite joints. The shear and tensile strength of the adhesive joints increased by addition of Al₂O₃ up to 1.5 wt%, which decreased by further addition of the nanofiller. Introduction of the nanoparticles caused a reduction in the peel strength of the joints. DSC analysis revealed that the glass transition temperature (Tg) of the adhesives rose by increasing the nanofiller content. The advancing water contact angle was decreased for adhesives containing nanoparticles. SEM micrographs indicated good dispersions of the Al₂O₃ nanoparticles within the acrylic matrix in the specimens with up to 1.5 wt% Al₂O₃ and revealed that addition of nanoparticles altered the fracture morphology from smooth to rough fracture surfaces.     

Lignin and Lignin-Derived Compounds for Wood Applications—A Review

Improving the environmental performance of resins in wood treatment by using renewable chemicals has been a topic of interest for a long time. At the same time, lignin, the second most abundant biomass on earth, is produced in large scale as a side product and mainly used energetically. The use of lignin in wood adhesives or for wood modification has received a lot of scientific attention. Despite this, there are only few lignin-derived wood products commercially available. This review provides a summary of the research on lignin application in wood adhesives, as well as for wood modification. The research on the use of uncleaved lignin and of cleavage products of lignin is reviewed. Finally, the current state of the art of commercialization of lignin-derived wood products is presented.     

胶黏剂中的化学*——2020年美国国家化学周活动介绍及启示

重点介绍2020年美国国家化学周——“胶黏剂中的化学”实验活动,对科学阅读和采访未来科学家活动作简要介绍。以此得出本次化学周活动对我国化学教学的几点启示:(1)大概念视角,加深结构化认识;(2)扎根实践,提高应用意识;(3)鼓励探析,深化本质意识;(4)跨界科学,渗透STSE理念;(5)精选主题,凸显微型项目;(6)勤研善思,塑造优秀品格。     

Various ways to strengthen the fiber‐matrix interface for enhanced composite performance

Surface treatment (ST) of carbon fibers (CF) leads to an enhancement in fiber‐matrix adhesion. However, it deteriorates the strength of a fiber which makes its reinforcing action less effective in a composite. These effects in opposite directions control the net strength of a composite, and hence, the treatment has to be judiciously applied, which would enhance the first factor and minimize the second one. Authors have recently reported on four effective techniques (using various doses) such as treatments with nanoparticles of Ytterbium fluoride (YbF₃)_, cold remote nitrogen–oxygen plasma (CRNOP), γ‐ray irradiation and nitric acid oxidation. Amongst these methods, nitric acid oxidation is studied in depth in the literature, and γ‐ray irradiation is sparingly studied. However, nano‐YbF₃ and CRNOP were first time reported in the literature by the authors. However, comparative aspects of all these methods were not addressed. In this paper, these aspects in details are discussed to lay down the right criteria for selection of a ST technique of CF to design the desired performance of a composite. The composites with polyetherimide and treated CF (including untreated) were developed and evaluated for various properties including tribological one. Treated CF based composites exhibited excellent mechanical and tribological properties (under harsh operative conditions with wear rates ≈ 1 × 10^?15 m³/Nm and μ ≈ 0.09). It was concluded that for strength and tribo‐performance, different treatments and doses are to be employed. Overall nanosized‐YbF₃ treatment of CF proved to be the most promising ST method. Copyright © 2013 John Wiley & Sons, Ltd.     

烯丙基化碳纳米管改善丙烯酸酯压敏胶的性能

本文利用γ-甲基丙烯酰氧基丙基三甲氧基硅烷(KH570)对多壁碳纳米管(MWNTs)进行修饰使其表面接枝上烯丙基官能团,与丙烯酸酯类单体进行原位聚合,制备了一种耐高温丙烯酸酯压敏胶(PSA)。 通过傅里叶变换红外光谱仪(FT-IR)、热重分析仪(TGA)和扫描电子显微镜(SEM)表征了MWNTs和丙烯酸酯PSA的结构与性能,探讨了改性MWNTs的质量分数对PSA耐热性能和粘接性能的影响。 结果表明,与未改性的丙烯酸酯PSA相比,当改性MWNTs的质量分数为1.5%时,改性丙烯酸酯PSA的耐热性能和粘接性能最佳,热分解温度从360 ℃提高到了382 ℃,耐热温度从80 ℃提高到了155 ℃,初粘力、持粘力和180°剥离强度分别从2 h和13.66 N/(25 mm)(12号小球)提高到了27 h和17.34 N/(25 mm)(17号小球)。