Numerical study on thermal performance of TiO2, Fe3O4 and NiCr/engine oil in an inclined wavy pip

The essential intention of the existing article is to illustrate the effect of wall properties on flow and thermal behavior, through a sinusoidal inclined wavy pipe. To succeed this phenomena we assume a sinusoidal pipe consist of wavy surface, whose walls traveling down to its borders and located at an inclined position, moreover titanium dioxide (TiO₂), ferrosoferric oxide (Fe₃O₄) and nichrome (80% Ni and 20% Cr) are considered as nano-particles and unused engine oil is assumed as a base fluid. The arising mathematical equations for thermal and flow ratio with wall slip impact are solved by mathematica. Also, evaluate graphically the thermal and flow behavior of nanofluids for multi values of solid volume fractions (η), rigidity parameter (M₁), stiffness parameter (M₂), viscous damping parameter (M₃), Grashof number (G_r), slip parameter (β) and heat generation parameter (H) also discuss the streamlines for different values of solid volume fraction.     

煤直接液化油中混合酚的分离研究

利用分子筛择形特点，对煤直接液化油中的混合酚实施高效分离。本研究选取间甲酚和对甲酚作为分离煤直接液化油馏分段混合酚的模型化合物，采用化学液相沉积法对HZSM-5吸附剂的孔口结构进行改变，分析分子筛硅铝比及颗粒粒径对模型化合物间甲酚和对甲酚吸附分离性能的影响，以获得高性能固相吸附剂，并将其应用于180-190℃馏分段混合酚分离。结果表明，当分子筛硅铝比为25、粒径为3-5 μm时，分子筛的孔口结构调节效果最优；当正硅酸乙酯的最小用量为0.2 mL/g时，固相吸附剂的吸附量为0.03 g/g，对甲酚选择性高于95%。由于外表面沉积物对吸附剂的孔口结构变化，导致对甲酚选择性的提高。进一步采用HZSM-5（1）吸附剂对真实煤直接液化油混合酚的分离中发现，苯酚和对甲酚的选择性均达到100%。     

Morphologically controlled synthesis of 1-dimensional selenium dioxide and study of its application as catalyst for diesel fuel additive

In this research work, selenium dioxide (SeO₂) nanorods have been prepared by a solvothermal method in which a strong reducing agent (NaBH₄) was used to reduce precursor salt into SeO₂ nanorods. X-ray diffraction (XRD) technique was applied to observe the crystal structure which confirmed its tetragonal geometry. Moreover, morphology and particle size were studied by scanning electron microscopy (SEM). SEM fully described the 1-dimensional morphology of SeO₂ nanorods which then arranged themselves to create a 3-dimensional flower-like structure with an average particle size of 50 nm. Also, the catalytic activity of SeO₂ nanorods as diesel-additive was studied by defining different parameters such as fire and flash points, calorific value, cloud and pour points, specific gravity, and kinematic viscosity. Subsequently, SeO₂ nanorods proved to be an excellent diesel additive due to higher total heat content and lower value of kinematic viscosity which enhances the better performance of the diesel engine.     

Preparation of macromonomers by copolymerization of methyl acrylate dimer involving β fragmentation

The unsaturated dimer of methyl acrylate [CH₂C(CO₂CH₃)CH₂CH₂CO₂CH₃, or MAD] was copolymerized with various monomers to prepare copolymers bearing the ω-unsaturated end group [CH₂C(CO₂CH₃)CH₂ ] arising from β fragmentation of the MAD propagating radical. Copolymerizations of MAD with cyclohexyl and n-butyl acrylate resulted in copolymers with ω-unsaturated end groups, and increasing the temperature up to 180 °C resulted in an increase in the rate of β fragmentation of MAD radicals relative to propagation. Only a small amount of unsaturated end groups was introduced by copolymerization with ethyl methacrylate (EMA), and the EMA content in the copolymer increased with temperature. These findings could be explained by the reversible addition of the poly(EMA) radical to MAD. The copolymerization with ethyl α-ethyl acrylate (EEA) did yield a copolymer containing unsaturated end groups with MAD units as part of the main chain, although the steric hindrance of the ethyl group suppressed homopropagation and crosspropagation of EEA, resulting in low polymerization rates. Therefore, the copolymerization of MAD with acrylic esters at high temperatures was noted as a convenient route for obtaining acrylate–MAD copolymers bearing unsaturated end groups at the ω end (macromonomer). © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 597–607, 2004     

Comparative behavior of polybutadiene and polynorbornene‐based latices prepared by dispersion ring‐opening metathesis polymerization with a poly(ethylene oxide) macromonomer

This study critically examines the similarities and differences between poly(ethylene oxide) (PEO) stabilized latices of polynorbornene and polybutadiene. Features such as the kinetics of copolymerization of norbornene and cyclooctadiene with a macromonomer of PEO, the particles' size and morphology, the type of copolymer formed, and the stability of these latices were investigated and the results obtained are considered. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 2705–2716, 2004     

新疆野生黑加仑与马林果实的营养成分分析

通过对新疆野生黑加仑和野生马林的脂肪油，8种微量元素，17种氨基酸以及维生素C的含量进行测定得出：黑加仑脂肪油含量为17．9％，马林的脂肪油含量为22．3％，其中，黑加仑脂肪油中，r－亚麻酸的含量为19．02％，而马林中，其含量为9．40％，黑加仑中K，Na,Ca,Cu,Zn,Fe的含量比马林中的含量高，而Mn,Mg元素的含量却比马林含量低；马林的维生素C含量为16．22mg/g，黑加仑的含量为108mg/g，黑加仑的氨基酸的总量为1．63％，马林为1．14％。     

Feasibility study for the preparation of certified reference materials part I – mineral oil contaminated soils

The international joint project HYCREF (Contract No. G6RD-CT-2002-00854), funded by the European Commission in the 5th Framework programme, aimed to develop methods to prepare homogeneous and stable reference materials of water, soil, and waste contaminated with mineral oil hydrocarbons and to certify the mineral oil content by gas chromatographic methods. The results of a feasibility study for the preparation of three soil reference materials are discussed in this paper, and for the preparation of three waste reference materials in the second part (Koch et al., Accred Qual Assur submitted for publication). The soil materials were selected to represent different soil types and contamination levels. The project plan set three requirements for these reference materials: uncertainty in the mineral oil content resulting from the certification exercise <5%, a sample inhomogeneity of <3% and a minimum long-term stability of 5 years. For the most part, these requirements were met within this project.     

Novel acrylic macromonomer with amphiphilic character derived from Triton X‐100: Radical copolymerization with methyl methacrylate and thermal properties

This article explores the synthesis of a novel methacrylic macromonomer with an amphiphilic character derived from poly(ethylene glycol) tert‐octylphenyl ether (MT) and its respective homopolymer. To know their reactivity in radical copolymerization reactions with methyl methacrylate (MMA), a model monomer (MTm) was synthesized to determine the reactivity ratios and compare them with the low molar fractions of copolymers of MT with MMA because they were difficult to isolate. They were r_MTm = 0.97 and r_MMA = 0.95. The compositional diagrams when representing the weight fraction of MT and MTm in the feed and the copolymer suggested that a clear correlation exists between the experimental points of the model monomer MTm and the macromonomer MT ones, suggesting that the length of the side poly(ethylene oxide) chain does not affect the reactivity of the methacrylic double bond in the prepared monomers for this type of polymerization reaction. The reactivity ratios of the copolymers have a tendency for the formation of random or Bernoullian copolymers. The glass‐transition temperatures (T_g's) of the prepared copolymers were determined by differential scanning calorimetry, deviated from the Fox equation, and discussed on the basis of treatments that consider the influence of the monomeric units along the copolymer chains, determining the T_g of the corresponding alternating dyads. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 1641–1649, 2003     

A RAPID APPROXIMATION FOR PREDICTING THE HYDROCARBON DISCOVERY RATE: PART 1. ASSESSING THE ACCURACY

The hydrocarbon discovery prediction problem is important to firms having to make decisions about the deployment of scarce exploration resources. Traditional methods for estimating the discovery rate rely on the completion of time consuming simulation experiments. A rapid approximation that does not require the completion of simulation exists and has been shown to have some promise as a prediction tool. This paper investigates the accuracy of the approximation method under a wide variety of distributional and drilling efficiency assumptions. The results indicate that the approximation produces predictions close to those of simulation under most of the tested conditions. This suggests that resource exploration firms could conveniently use the method for a wide variety of planning purposes without incurring the same costs in time and personnel required for simulation.