乙酰化淀粉的塑化和性能研究

以乙酰化改性淀粉为基体,甘油为增塑剂,利用哈克旋转流变仪密炼制备热塑性乙酰化淀粉.实验结果表明制备热塑性乙酰化淀粉的甘油/乙酰化淀粉配比应大于30/100(W/W),且随甘油含量增加,热塑性乙酰化淀粉的脆性降低.动态机械热分析(DMTA)显示热塑性乙酰化淀粉包含富甘油和富淀粉两相,乙酰化淀粉和甘油为部分互溶.流变学分析显示淀粉分子间作用力非常强,表现为类固态行为.同时本文对材料的热稳定性进行了初步研究.     

A Novel Plasticizer for the Preparation of Thermoplastic Starch

TPS was a biodegradable material based on starch. Starch was an inexpensive and natural renewable polysaccharide, which was widely investigated as the substitute of petroleum-derived plastics. Native starch commonly existed in granule structure with about…     

接枝和交联对纳米Si02改性NR／PP共混型热塑弹性体的影响

动态硫化制备纳米二氧化硅（SiO2）改性天然橡胶，聚丙烯共混型热塑性弹性体（NR/PPTPE）．研究了马来酸酐，苯乙烯，过氧化二异丙苯（MAH／St／DCP）多单体“就地”熔融接枝、交联对TPE力学性能、耐溶剂性能和耐热变形性能的影响，并用SEM分析了TPE的断面形貌．结果表明：纳米SiO2和MAH／St／DCP的最佳质量分数分别为0．03和0．0375／0．0188／0．00375时，MAH／St／DCP接枝、交联改性NR／PP／纳米SiO：TPE的力学性能、耐溶剂性能和耐热变形性能最佳．MAH／St／DCP“就地”接枝、交联通过细化交联NR分散相、改善交联NR分散的均匀性和增加两相之间的共交联，使NR与PP两相界面结合强度明显提高，NR／PPTPE的综合性能得到明显的改善．     

水煤浆添加剂与煤之间的相互作用规律研究 Ⅰ. 复合煤颗粒间的相互作用对水煤浆流变性的影响

使用12种不同分散剂对14种不同变质程度的煤进行了成浆性实验，分析了182个水煤浆(CWS)样品的流变性。结果表明，低变质程度和高灰煤浆多呈屈服假塑性，煤的性质起主导作用；变质程度高且灰分较低煤浆的流变性，主要依赖于分散剂的结构与性质；分子结构单元立体空间效应大，疏水基团与亲水基团呈立体间隔分布的分散剂，易形成屈服假塑性CWS；分子线度长，亲水基团与疏水基团呈线性间隔分布的分散剂，易形成胀塑性CWS。复合煤粒间的相互作用方式是决定CWS流变特性的关键。     

不同水煤浆分散剂与煤之间的相互作用规律研究Ⅹ分散剂在煤粒表面上的吸附作用特征

研究了6种水煤浆分散剂在14种不同变质程度煤上的吸附作用特征。结果表明,多数分散剂在煤粒表面达到单层饱和吸附后,又形成多层吸附,单层饱和吸附量与煤的变质程度、比表面积以及分散剂的性质有关。在相同粒度分布下,煤的变质程度越低,表面含氧亲水官能团的比例越高,孔隙率越高,比表面积越大,这对增大吸附量有利。煤的变质程度越高,其表面疏水区面积的比例越高,分散剂通过疏水基团紧密吸附在煤表面的比例越大,这对增加高阶煤的吸附量有利。对不同煤,是变质程度还是比表面积为吸附分散剂的主控因素,主要依赖于分散剂的结构与性质。对同种煤,疏水与亲水基团呈线型分立分布的分散剂,吸附量明显高;而疏水与亲水基团呈线型间隔分布的分散剂,吸附量明显小。     

静电纺丝法制备酚醛纤维研究进展

酚醛树脂是一种广泛使用的合成树脂,包括热固性和热塑性两类,具有良好的阻燃性、耐热性和耐腐蚀性。酚醛纤维是由酚醛树脂所制成的交联纤维,传统的酚醛纤维制备方法有熔融纺丝法和湿法纺丝法,后来出现了静电纺丝法。本文根据酚醛树脂的种类分别介绍了热固性、热塑性和热塑/热固混合酚醛树脂三类材料静电纺丝的研究进展。在改善酚醛纤维特性方面,综述了四种优化措施,包括加入无机盐、微波辐射辅助固化、非匀速阶梯式加热固化、氧化石墨烯修饰的静电纺丝法等。此外,对本实验室制备酚醛纤维的研究也进行了概述,阐述了酚醛纤维当前存在的问题及未来发展方向。     

Statistical and experimental investigation on low density microcellular foaming of PLA-TPU/cellulose nano-fiber bio-nanocomposites

This study dedicates to foaming of biocompatible blends of polylactic acid and thermoplastic polyurethane reinforced with bio-degradable cellulose nanofibers. This research primarily was associated with fabrication of PLA-TPU nanocomposites using a low weight fraction of cellulose nanofibers as a biodegradable reinforcement. Microstructural and mechanical properties of fabricated nanocomposites were examined and diffractometry was utilized to verify formation of percolated nanocomposites. Microcellular foaming was then performed with CO₂ as a blowing agent. Central composite design was applied in designing the experiments to evaluate the effects of main operating variables consisting of saturation pressure and time, heating time and foaming temperature. The results demonstrated that high saturation pressure and time promoted low cell diameters (below 5 μm) and high cell densities (above 10⁹ cell/cm³) due to the grown degree of crystallinity and higher PLA-TPU miscibility. Accordingly, adding TPU and CNF to the matrix create high crystalline foamed samples decorated with low bulk density.     

THERMOPLASTIC ELASTOMERS. II. POLY(ETHER-ESTER-IMIDE)S BASED ON 1,4-DIAMINOBUTANE,TRIMELLITIC ANHYDRIDE, 1,4-DIHYDROXYBUTANE,AND POLY(ETHYLENE OXIDE)S

A series of new poly(ether-ester-imide)s, PEEIs, was prepared from an imide dicarboxylic acid based on 1,4-diaminobutane and trimellitic anhydride. This imide dicarboxylic acid polycondensed with 1,4-dihydroxybutane formed the hard segments and poly(ethylene oxide), PEO-1000, or mixtures of PEO-1000 and poly(tetramethylene oxide), PTMO-1000, were used as soft segments. Whenever PTMO-1000 was used as comonomer, macrophase separation was observed at the end of the polycondensation. However, this macrophase separation had little influence on the mechanical properties. A poly(ether-esterimide), PEEI, containing neat PEO-1000 was characterized by dynamic mechanical thermoanalysis, stress-strain and hysteresis measurements, and by melt rheology. The mechanical properties were compared with those of an analogous PEEI containing neat PTMO-1000 and with those of a poly(ether-ester), PEE, based on poly(butylene terephthalate) hard segments and PTMO-1000.     

Nanoparticle Halos Mechanism in Stabilizing of Colloidal Suspensions: Polymeric Binder and Dispersant Effects

Dispersion behavior of colloidal Al₂O₃ aqueous suspensions was investigated in the presence of highly charged CeO₂ nanoparticles and polymeric additives. It was found that among the investigated parameters, ceria nanoparticles concentration had the highest significant effect on the stability of Al₂O₃-CeO₂ suspensions. However, the low influence of dispersant concentration may be due to significant role of ceria nanoparticles stabilizing alumina microspheres by “nanoparticle halo” formation. The stabilization of the bidispersed suspensions was also evidenced by scanning electron microscopy and elemental analysis of the sediment layers after three weeks.     

采用反应挤出三次加料法合成苯乙烯/异戊二烯/苯乙烯

以同向啮合双螺杆挤出机为反应器,采用苯乙烯和异戊二烯为聚合单体,以正丁基锂为引发剂,采用三次加料法合成苯乙烯/异戊二烯/苯乙烯(SIS)三嵌段热塑性弹性体.氢核磁共振(1H NMR)谱分析结果表明,共聚物中聚异戊二烯嵌段以1,4-结构为主.采用四氧化锇催化双氧水氧化降解聚合物分子链,利用凝胶渗透色谱对氧化降解后的聚苯乙烯碎片进行分析,证明共聚物分子为(聚苯乙烯-聚异戊二烯-聚苯乙烯)(PS-PI-PS)三嵌段结构.动态力学分析(DMA)及透射电子显微镜(TEM)分析结果表明,SIS具有两相分离结构.拉伸试验结果表明,共聚物拉伸强度与苯乙烯含量有关.