Khillah extract as inhibitor for acid corrosion of SX 316 steel

The inhibitive effect of the extract of khillah (Ammi visnaga) seeds, on the corrosion of SX 316 steel in HCl solution was determined using weight loss measurements as well as potentiostatic technique. It was found that the presence of the extract reduces markedly the corrosion rate of steel in the acid solution. The inhibition efficiency increases as the extract concentration is increased. The inhibitive effect of khillah extract was discussed on the basis of adsorption of its components on the metal surface. Negative values were calculated for the energy of adsorption indicating the spontaneity of the adsorption process. The formation of insoluble complexes as a result of interaction between iron cations and khellin, which present in the extract, was also discussed.     

Improvement of the properties of polyarylate reinforced with liquid crystalline polymers

Blends of polyarylate of bisphenol A, PAr, with two commercial main chain liquid crystalline polymers, Vectra A950 and Vectra B950, are studied. From dynamic viscoelastic measurements it is deduced that both systems (PAr/Vectra A950 and PAr/Vectra B950) are immiscible and scanning electron microscopy (SEM) micrographs show the presence of spherical domains of the liquid crystalline polymer when PAr constitutes the matrix. Extrusion capillary measurements reveal that, under conditions of temperature and shear rate similar to those of processing, the viscosity is reduced to approximately 10% of its value when the content of liquid crystalline polymer is only 20%. This great improvement of the rheological properties is observed in both PAr/Vectra A950 and PAr/Vectra B950 blends. The effect of draw ratio on Young's modulus for different compositions is also analyzed, pointing out the reinforcing action of both liquid crystalline polymers on polyarylate: for instance, 20% of Vectra B950 in the blend gives rise to a 700% increase of the modulus of fibres prepared at a draw ratio of 50. SEM of the extrudates reveals that the spherical domains are elongated at the entrance of the capillary giving rise to a microfibrillar morphology which is related to the excellent rheological and mechanical properties of the blends.     

An estimation of the measurement uncertainty for an optical emission spectrometric method

 A validation procedure based on the ISO/IEC 17025 standard was used to demonstrate the long-term stability of a calibration process and to assess the measurement uncertainty of a standard test method for optical emission vacuum spectrometric analysis of carbon and low-alloy steel (ASTM E 415–99a). The validation was used to provide documented evidence that the selected method fulfils the requirements and that the method is ”fit for purpose”. A test for drift was applied to determine statistically whether the analytical results vary systematically with time. The accuracy and traceability of the optimised method were tested by an analysis of closely matched matrix certified reference materials (CRMs). The measurement uncertainty estimations took account of the precision study, the bias and its uncertainty, and the qualification of uncertainties not considered in the overall performance studies. Received: 2 November 2002 Accepted: 2 January 2003 Acknowledgement The author expresses gratitude to Dr. Aleš Fajgelj for helpful discussions during the 3rd Central European Conference on Reference Materials and Measurements. Presented at CERMM-3, Central European Reference Materials and Measurements Conference: The function of reference materials in the measurement process, May 30–June 1, 2002, Rogaška Slatina, Slovenia Correspondence to T. Drglin     

钢球质量监测最佳抽检方案的确定

本文介绍概率抽样法在钢球生产过程中的应用,通过此法确定钢球生产中各工序质量监测的最佳抽检方案,以确保产品被接受的概率最大。     

Coulometric argentometric determination of microamounts of sulphur in iron and steel after reduction to hydrogen sulphide with iron(II) in strong phosphoric acid medium

A coulometric method was developed for the determination of microamounts of sulphur in iron and steel. Hydrogen sulphide is quantitatively evolved by reduction with iron(II) in strong phosphoric acid medium and is titrated with electrolytically generated silver ion from a silver anode. Microamounts of sulphide (2.96–224.3 μg) in sodium sulphide standard solutions could be determined with an error of only a few percent. Sulphur in a potassium sulphate standard solution is quantitatively reduced to hydrogen sulphide and could be separated from the solution by heating and determined accurately. Trace amounts of sulphur (7–100 μg g^?1) in iron and steels could be determined with a standard deviation of 0.7–2.1 μg g^?1.     

The way to measure quantitatively full dissolution and crystallization of polyamides in water up to 200 °C and above by DSC

The way to measure quantitatively full dissolution and crystallization of polyamides in water up to 200 °C and above by DSC is described. Stainless-steel high-pressure pans enable research on fully dissolving polyamides in water under vapor pressure. The results show clearly that polyamide 6 (PA6) is soluble in water under vapor pressure in the whole concentration range and that water acts as a crystallization and melting point suppressor. The maximum temperature depression is approximately 60 °C. This depression of the transitions is independent of concentration over a large range (10-70 mass% PA6 in water). When PA6 dissolves in water during heating, the polymer often sets to the sides of the DSC sample pan. Because of this the contact between the sample and the bottom of the pan reduces during measurement and therefore DSC heating curves are frequently curved. Adding steel wool to these stainless-steel high-pressure pans improves the measurements by increasing the thermal conductivity between the sample and pan bottom, and as a result the DSC curves become less curved. The interpretation of the measurements improves and the possibility of reproducible peak area calculations also in heating comes in sight.     

聚合物二元体系动态力学性能的估算

动态热机械分析是多相聚合物体系的一个重要研究手段.分析动态力学性能可以研究共混高聚物的相容性、复合材料的界面特性以及高分子运动机理等.本文综述了聚合物二元体系,即填充、纤维增强、共混体系动态力学性能的估算方法.在填充体系中,分别概述有无界面作用两种情况,当存在界面作用时,界面作用越强,模量越大,阻尼越小.对纤维增强体系,讨论了玻璃纤维有无取向的情况下模量和阻尼的估算.特别对于聚合物二元共混体系,分"海-岛"结构和双连续相两种情况,分别讨论了模量与阻尼的估算.     

Synthese de Nouveaux Derives Phosphones a Chaine Perfluoree et Leurs Proprietes Adhesives Sur Acier

Ce mémoire décrit la synthèse de phosphonates comportant une chaîne perfluorée. Ces composés sont obtenus par la télomérisation d'allylphosphonates de dialkyle en présence d'un agent de transfert fluoré de type mercaptan. Ensuite, nous employons deux méthodes de déalkylation menant sélectivement soit au monoacide soit au diacide phosphonique. Tous ces produits comprenant une extrémité de chaîne phosphonée, sous forme acide ou ester, ont été caractérisés et leur adhésion respective sur des plaques d'acier est étudiée. Ces tests montrent que le monoacide phosphonique est un excellent promoteur d'adhésion et qu'il est aussi efficace que le diacide. This article describes the synthesis of phosphonic derivatives bearing a perfluorinated chain. These compounds have been synthetized by telomerization of dialkyl allylphosphonate with a fluorinated transfer agent type mercaptan. Then two methods of dealkylation leading selectively were used to mono or to diacid phosphonic moieties. All the products bearing phosphonic end-groups, more or less acidic, have been characterized and their own adhesion on steel plates is studied. These tests show that phosphonic monoacid is an excellent adhesion promoter on steel, as efficient as the diacid compound.     

烧结烟气脱硫脱硝用活性炭混合钢渣复合材料的光谱学分析

钢渣是冶金工业中产生的主要固体废弃物,其产量约为每年粗钢产量的15%~20%。由于技术的局限,导致我国钢渣利用率较低,仅为年钢渣产量的10%,同时加之管理制度的不健全,导致钢渣大量露天堆放,对土地资源、地下水源,以及空气质量形成严重影响。固体废弃物再利用是资源可持续发展的重要途径之一,钢渣的主要化学成分为CaO, SiO2, Al2O3, MgO, Fe2O3, MnO, f-CaO等。面对上述问题,利用冶金固体废弃物与活性炭开发一种价格低廉且性能优越的活性炭混合钢渣复合材料,既是冶金固体废弃物的高附加值利用与资源可持续发展的重要途径之一,也是大幅降低改性活性炭生产成本与提高经济效益的重要途径之一。该研究创新性以活性炭与钢渣为研究对象,利用钢渣中含有的金属氧化物对活性炭进行改性处理制备用于烧结烟气脱硫脱硝的活性炭混合钢渣复合材料,通过搭建实验反应装置对活性炭混合钢渣复合材料的脱硫脱硝性能进行测试。利用X射线荧光光谱仪(XRF)对钢渣的化学成分进行测试与分析,比表面积及孔径测定仪(BET)对活性炭混合钢渣复合材料的孔结构进行测试与分析,傅里叶变换红外光谱仪(FTIR)对钢渣的结构组成进行测试与分析,扫描电子显微镜(SEM)对活性炭混合钢渣复合材料的微观结构进行测试与分析,以揭示活性炭与钢渣制备活性炭混合钢渣复合材料的机理,以及活性炭混合钢渣复合材料对烧结烟气脱硫脱硝的机理。结果表明:当钢渣为电炉热泼渣、钢渣与活性炭质量比为2∶4、钢渣与活性炭细度为400目时,活性炭混合钢渣复合材料具有良好的脱硫脱硝性能与合理的经济性,即脱硫效率为100%、脱硝效率为58%。活性炭混合钢渣复合材料具有的多孔结构对SO2和NO进行有作用,钢渣中Fe2O3与MnO2促使活性炭官能团进行催化还原反应提高脱硫脱硝性能,其中吸附作用是主导与前提,催化还原反应是辅助与协同。以期为高附加值的钢渣利用提供新途径,实现钢铁企业以废治废、以废增效的目的。     

腐蚀介质中混凝土/钢筋界面电极电位分布的立体分析

由于混凝土的隔离和高绝缘性 ,常规的电化学技术、微探针扫描技术均难于获得在腐蚀介质的浸泡下混凝土 /钢筋界面 ,特别是不同深处的混凝土 /钢筋界面的电位分布 .本文提出用阵列电极法并结合电子技术和微机控制技术 ,获得同一水平面上混凝土 /钢筋界面以及不同深处的混凝土 /钢筋界面的电位分布立体信息图 .结果表明 :在NaCl介质中经过一段时间的浸泡 ,混凝土中的钢筋腐蚀可发生并发展 ;而在Na2 SO4 介质中经过一段时间的浸泡 ,虽钢筋腐蚀一般不发生 ,但混凝土可能破坏 .不同深处混凝土 /钢筋界面腐蚀优先发生在混凝土覆盖较浅的部位 .