Vacuum‐driven fluid manipulation by a piezoelectric diaphragm micropump for microfluidic droplet generation with a rapid system response time

Recently, we developed a convenient microfluidic droplet generation device based on vacuum‐driven fluid manipulation with a piezoelectric diaphragm micropump. In the present study built on our previous work, we investigate the influence of settings applied to the piezoelectric pump, such as peak‐to‐peak drive voltage (V_p‐p) and wave frequency, on droplet generation characteristics. Stepwise adjustments to the drive voltage in ±10‐V_p‐p increments over the range of 200?250 V_p‐p during droplet creation revealed that the droplet generation rate could be reproducibly controlled at a specific drive voltage. The droplet generation rate switched within <0.5 s after the input of a new voltage. Although the droplet generation rate depended on the drive voltage, this setting had almost no influence on droplet size. The frequency over the selected range (50?60 Hz) did not markedly influence the droplet generation rate or droplet size. We show that the current fluid manipulation system can be conveniently used for both droplet generation and for rapid droplet reading, which is required in many microfluidic‐based applications.     

Multi-cracks problem for piezoelectric materials strip subjected to dynamic loading

This paper analyses and models the dynamic interaction among permeable multi-cracks in a piezoelectric strip under anti-plane shear waves by the Schmidt method. The Fourier transform is applied and then two pairs of triple integral equations can be solved using the Schmidt method. The results show that the stress and the electric displacement intensity factors of cracks depend on not only the crack length and the piezoelectric coefficient, but also the thickness of the piezoelectric strip, the distance between multi-cracks and the frequency of incident wave.     

Indentation responses of piezoelectric films

Frictionless indentation responses of transversely isotropic piezoelectric film/rigid substrate systems under circular cylindrical indenter (i.e., punch), conical indenter (i.e., cone), and spherical indenter (i.e., sphere) are investigated. Both insulating and conducting indenters are considered. The technique of Hankel transformation is employed to derive the corresponding dual integral equations for the mixed boundary value indentation problems. For the two limiting cases of infinitely thick and infinitely thin piezoelectric films, closed-form solutions are obtained. For piezoelectric films of finite thickness, a numerical method is constructed to solve the dual integral equations and semi-empirical models having only two unknown parameters are proposed for the responses of indentation force, electric charge and electric potential, and contact radius. With the two parameters inferred from the numerical results, the semi-empirical formulae are found to provide good estimates of the indentation responses for the two limiting cases of infinitely thick and thin piezoelectric films, as well as those in between. The inferred parameters in the proposed semi-empirical formulae for normalized indentation force and electric charge are checked against four different piezoelectric materials and are found to be insensitive to the selection of piezoelectric materials. It is believed that the proposed semi-empirical indentation formulae are useful in developing experimental indentation techniques to extract the material properties of piezoelectric films.     

An Oscillation Condition for an Electrode－separated Piezoelectric Sensor in Non－electrolyte Liquid

ＡｎＯｓｃｉｌｌａｔｉｏｎＣｏｎｄｉｔｉｏｎｆｏｒａｎＥｌｅｃｔｒｏｄｅ－ｓｅｐａｒａｔｅｄＰｉｅｚｏｅｌｅｃｔｒｉｃＳｅｎｓｏｒｉｎＮｏｎ－ｅｌｅｃｔｒｏｌｙｔｅＬｉｑｕｉｄＳＨＥＮＤａ－ｚｈｏｎｇ，ＨＵＡＮＧＭｉｎｇ－ｓｈａｎ，ＬＩＮＳｏｎｇ，Ｎ...     

Oscillation condition for a series piezoelectric sensor. Application to the determination of urease activity in plant seeds

The oscillating conditions for a series piezoelectric quartz crystal (SPQC) are proposed and verified experimentally. The influence of the cell constant and oscillator phase on the oscillational ability of the SPQC was investigated. It is shown that the SPQC possesses excellent oscillational ability in low or high conductivity solutions, but in solution of intermediate conductivity, the oscillational ability decreases with increasing oscillator phase or decreasing cell constant, sometimes resulting in a cease-to-oscillate zone. The SPQC was applied to determine the urease activity in plant seeds with a detection limit of 0.004 U ml⁻¹, based on the change in conductivity.     

Biomimetic piezoelectric quartz sensor for caffeine based on a molecularly imprinted polymer

A piezoelectric quartz sensor coated with molecularly imprinted polymer (MIP) for caffeine was developed. The MIP was prepared by co-polymerizing methacrylic acid (MAA) and ethylene glycol dimethacrylate (EDMA) in the presence of azobis(isobutyronitrile) as initiator, caffeine as template molecule, and chloroform as solvent. The MIP suspension in polyvinyl chloride/tetrahydrofuran (6:2:1 w/w/v) solution was spin coated onto the surface of the electrode of a 10 MHz AT-cut quartz crystal. The sensor exhibited a linear relationship between the frequency shift and caffeine concentration in the range of 1×10^–7 mg mL^–1 up to 1x10^–3 mg mL^–1 [correlation coefficient (r)=0.9935] in a stopped flow measurement mode. It has a sensitivity of about 24 Hz/ln(concentration, mg mL^–1). A steady-state response was achieved in less than 10 min. The performance characteristic of the sensor shows a promising and inexpensive alternative method of detecting caffeine. Surface studies were carried out for the reagent phase of the sensor using SEM, AFM, and XPS analysis in order to elucidate the imprinting of the caffeine molecule. The SEM micrograph, AFM image, and XPS spectra confirmed the removal of caffeine by Soxhlet extraction in the imprinting process and the rebinding of caffeine to the MIP sensing layer during measurement.     

Preparation and application of cryptand-coated piezoelectric crystal gas-chromatographic detector

A re-usable and sensitive cryptand-22-coated quartz-crystal membrane piezoelectric sensor with a homemade computer interface for signal acquisition and data processing was prepared and applied as a gas-chromatographic (GC) detector for various organic molecules. The oscillating frequency of the quartz crystal decreased due to the adsorption of organic molecules on cryptand-22. Effects of functional group, molar mass, steric hindrance and polarity of organic molecules on frequency responses of the cryptand-coated piezoelectric crystal detector were investigated. The cryptand-coated piezoelectric crystal GC detector had demonstrated high sensitivity for various polar organic molecules and good reproducibility when re-used. The frequency responses of the cryptand-coated crystal for various molecules were in the following order: carboxylic acids (RCOOH)primary amines (R-NH₂)>alcohols (ROH)>secondary amines (R₂NH)>tertiary amines (R₃N)>ketones. More polar molecules exhibited better frequency responses. The effect of temperature and amount of coating on the frequency responses of cryptand-coated crystal GC detector were also investigated. The cryptand-coated piezoelectric crystal GC detector compared well with the commercial thermal conductivity detector (TCD).     

电解沉积压电频移分析的理论与验证

提出了控制电位电解和恒电流电解两类电解沉积的压电频移分析法测定的理论公式,用实验结果验证了它的正确性.     

Graded PZT ceramics for piezoelectric transformers

In the present study two types of the synthesized Pb(Zr_1−xTi_x)O₃ (PZT) powders differing in Zr/Ti ratio were used to prepare the spatially inhomogeneous (i.e., graded) structure. A position-dependent chemical composition was expected to cause the property gradient. Disk-shaped compacts were prepared in a way such that two different orientations of the radial gradients were formed. The solid state sintering under pressure was utilized to prepare ceramics. Simultaneous thermal analysis was used to study thermal behavior of the ceramic powders. Graded PZT ceramics were characterized using X-ray diffraction, scanning electron microscopy and energy dispersive spectroscopy. It was also characterized in terms of its dielectric properties by both bridge technique and the impedance spectroscopy. On the basis of graded PZT ceramics the disk-shaped radial mode piezoelectric transformer was developed and fabricated.