Photonic crystal beam splitters

In this work, the beam splitter with two input ports and two output ports in two-dimensional photonic crystals is studied through the finite-difference time-domain method. The beam splitter consists of two orthogonally cross line defects. The diameter of the two diagonal air holes at the intersection of the two line defects was modified. The input light can be identically divided into the two output ports. The beam splitters can be applied in the photonic crystal Mach-Zehnder interferometers or photonic crystal optical switches.     

Imprint lithography of pyramidal photonic pillars using hydrazine etching

An inexpensive method to produce a pyramidal-type 2D photonic structures in the silicon substrate was proposed. The method is based on the combination of imprint lithography and wet Si1 0 0 etching in water solution of hydrazine, which etches 1 1 1 faces much more slowly than others. Thermally grown SiO₂ mask for the hydrazine etching was used, because single Al mask cannot be well bonded to the substrate and tends to peel during the etching. It was revealed that transmittance in the infrared spectrum region of the patterned silicon decreases by about five times compared with that of flat silicon substrate and this decrease is almost independent of the angle of the incident beam. In the infrared region, decrease of transmittance of the patterned samples is directly proportional to the wave number. The shape of formed pyramids has strong influence on the transmittance. Decrease of the transmittance is much more rapid and larger in the case of sharpless pillars.     

Decay distribution of spontaneous emission from atoms in one-dimensional photonic crystal

Spontaneous emission behavior from atoms (or molecules) in one-dimensional photonic crystal with a defect is investigated. Taken all the TE and TM modes into account, the normalized spontaneous emission rate of the atom is calculated as a function of the position of the atom in the crystal. Results for both nonabsorbing dielectric structure and absorbing dielectric structure are presented. With the increase of the thickness of the defect in which the atoms are embedded, the oscillations of the spontaneous emission rate versus the position of the atom become dense and the lifetime distribution becomes narrow and sharp. The PC effect may lead to the coexistence of both accelerated and inhibited decay processes.     

Laser nanosources based on planar photonic crystals as new platforms for nanophotonic devices

Two-dimensional photonic crystal lasers have been fabricated on III–V semiconductor slabs. Tuning of the spontaneous emission in micro and nanocavities has been achieved by accurate control of the slab thickness. Different structures, some of them of new application to photonic crystal lasers, have been fabricated like the Suzuki-phase or the coupled-cavity ring-like resonators. Laser emission has been obtained by pulsed optical pumping. Optical characterization of the lasing modes have been performed showing one or more laser peaks centred around 1.55 μm. Far field characterization of the emission pattern has been realized showing different patterns depending on the geometrical shape of the structures. These kinds of devices may be used as efficient nanolaser sources for optical communications or optical sensors.     

Interference of circularly polarized light: contrast and application in fabrication of three-dimensional periodic microstructures

The contrast of interference pattern formed by two circularly polarized waves and by a linearly polarized wave and a circularly polarized one is discussed. The results are compared with that by two linear beams. It shows that the use of circular light in holographic fabrication of three-dimensional periodic microstructures may remove the necessity of beam ratio and polarization optimization needed in the interference of three linear noncoplanar beams and improve the uniform contrast of resultant pattern simultaneously.     

聚苯乙烯乳胶球三维有序体的制备及其显微形貌表征

A three-dimensional (3D) ordered structure was achieved by self-organization of monodisperse polystyrene latex about 250nm in diameter after being ambient dried. The stacked morphology was investigated by scanning electron microscopy(SEM) observation. It is shown that the face-centered cubic(FCC) phase dominantly exists. This finding presents a potential template for preparing an inverse FCC structure as a photonic crystal of full band gap if the index contrast is higher than 2.8.     

Some exact solutions of generalized Zakharov system

In this paper, we seek exact solutions of generalized Zakharov system. We use extended trial equation method to obtain exact solutions of this system. Consequently, we obtain some exact solutions including soliton solutions, rational, Jacobi elliptic and hyperbolic function solutions of this system by using extended trial equation method.     

Simple model for blistering mechanism

A simple model for blistering mechanism is proposed for energies higher than 20 keV. The model assumes that through the nucleation of smaller bubbles, a critical bubble radius is reached. The planar stress results of Jeffery for a semi-infinite plate with a circular hole subject to a uniform inner normal pressure are roughly taken as valid for the three-dimensional case. Under this assumption, the thickness of the blister's cover and critical ion dose for blister formation are calculated from the knowledge of the mean projected range of ions and blister diameter taken from experimental results. The resulting values are in agreement with the experimental values reported. The model can qualitatively explain breakage at the top of the dome-shaped blisters observed in molybdenum at 1100 K.     

二苯磷酰基取代四苯基硅的合成及在构筑宽禁带聚合物中的应用

设计并合成了二苯磷酰基取代的四苯基硅基团,并将其作为宽禁带聚合物母体材料构筑基元,通过Suzuki反应偶连3,6位取代的咔唑合成了聚合物SiCzP.对聚合物的结构进行了系统的表征.与模型聚合物SiCz相比,二苯磷酰基的强吸电子能力,降低聚合物母体材料的LUMO能级,更有利于电子的注入.SiCzP与SiCz的玻璃化转变温度分别为219与227℃,失重5%时的分解温度分别为441与426℃.二者均具有良好的成膜性,掺杂器件初步结果表明,二苯磷酰基的引入使器件的亮度和效率都得到提高,其最大流明效率和功率效率比SiCz分别提高了98%和75%.     

Successive approximation-like 4-bit full-optical analog-to-digital converter based on Kerr-like nonlinear photonic crystal ring resonators

Implementing of photonic sampling and quantizing analog-to-digital converters (ADCs) enable us to extract a single binary word from optical signals without need for extra electronic assisting parts. This would enormously increase the sampling and quantizing time as well as decreasing the consumed power. To this end, based on the concept of successive approximation method, a 4-bit full-optical ADC that operates using the intensity-dependent Kerr-like nonlinearity in a two dimensional photonic crystal (2DPhC) platform is proposed. The Silicon (Si) nanocrystal is chosen because of the suitable nonlinear material characteristic. An optical limiter is used for the clamping and quantization of each successive levels that represent the ADC bits. In the proposal, an energy efficient optical ADC circuit is implemented by controlling the system parameters such as ring-to-waveguide coupling coefficients, the ring’s nonlinear refractive index, and the ring’s length. The performance of the ADC structure is verified by the simulation using finite difference time domain (FDTD) method.