环状连续强激光下光学薄膜的瞬温和热畸变

详细研究了非冷却光学薄膜元件在环形激光光束辐照下的瞬态温度分布和随后的热畸变，并且用泰曼干涉仪实际测量了连续波氧碘激光辐照各种非冷却光学元件的热畸变量并与理论计算相比较，分析结果表明理论和实验相一致。     

Indirect Methods For Determination of The Protective Effects of Coating Films on The Surface of Crystals

The extents of the protective effects of coating films on the surface of crystals were determined. Three different samples were made with different quantities of coating fluid (Sepifilm LP 010 in 10% aqueous solution). Since the atomizing rate was constant, the coating time increased in parallel with the volume of coating fluid applied. The direct measurement of film thickness and smoothness is very difficult, and therefore indirect methods were used. Dimenhydrinate was chosen as model drug; this is a heat-sensitive antihistamine with a low melting point. This temperature can be reached during the tableting process. The behaviour of samples on exposure to heat was examined by differential scanning calorimetry. The water uptakes of the samples were determined with an Enslin apparatus. Plasticity was studied with an instrumented tablet machine. These indirect methods (thermal conductivity, water uptake and plasticity measurements) revealed connections between the results of the various experiments. An overlong coating time decreased the protective effect of the coating film. This revised version was published online in August 2006 with corrections to the Cover Date.     

纳米氧化钛-乙二醇溶胶溶液的研究

选用了钛酸丁酯、硬脂酸和乙二醇作为表面活性剂，采用表面化学修饰和表面物理修饰2种方法修饰纳米氧化钛，然后分散在乙二醇溶剂中形成溶胶溶液．并通过红外光谱仪、紫外分光计、原子力显微镜，分析了表面化学修饰后的纳米氧化钛表面化学结构的变化，观测了纳米氧化钛溶胶在乙二醇溶剂中稳定性．试验结果表明表面活性剂与纳米氧化钛的表面的不饱和键之间形成了新的化学结构，粒子表面可能接枝上有机长链，提高了纳米粒子在溶剂中的相容性．表面化学修饰后的纳米氧化钛与乙二醇溶剂形成了较稳定的溶胶体系，而且纳米溶胶粒径较小．表面活性剂添加量与纳米粒子添加量控制在(1～1．2)：1时，可以获得纳米溶胶粒径较小，同时溶胶稳定性较好的纳米氧化钛-乙二醇溶胶体系．     

Optimal design of a convergent-barrel cold spray nozzle by numerical method

A convergent-barrel (CB) cold spray nozzle was designed through numerical simulation. It was found that the main factors influencing significantly particle velocity and temperature include the length and diameter of the barrel section, the nature of the accelerating gas and its pressure and temperature, and the particle size. Particles can achieve a relatively low velocity but a high temperature under the same gas pressure using a CB nozzle compared to a convergent-divergent (CD) nozzle. The experiment results with Cu powder using the designed CB nozzle confirmed that particle deposition can be realized under a lower gas pressure with a CB nozzle.     

Fabrication of patterned gold electrodes with spin-coated-and-fired Au(1 1 1) film by the soft lithography

We prepared high quality Au(1 1 1) film on Si wafer through the spin coating and thermal decomposition of a gold ink, spin-coated-and-fired (SCAF) Au film. The X-ray measurements, XRD and pole-figure analysis, showed that the SCAF Au film has a (1 1 1) out-of-plane orientation with a random in-plane orientation. In order to confirm the chemical activity of the SCAF Au film, we demonstrate the formation of patterned structures with the film by using soft lithography technique. The chemical activities of this physically stable SCAF Au film to the alkanethiols were at least equivalent those of physically deposited the Au films. The possibility of the mass production of micro patterned structure with the SCAF Au film was also demonstrated over the wide region on Si wafer by the microcontact lithography. These suggest that the Au film will help the easy fabrication of various nanosized devices on Si wafer and other substrates.     

Studies on calcium‐containing poly(urethane ether)s

The calcium salt of mono(hydroxyethoxyethyl)phthalate [Ca(HEEP)₂] was synthesized by the reaction of diethylene glycol, phthalic anhydride, and calcium acetate. Calcium‐containing poly(urethane ether)s (PUEs) were synthesized by the reaction of hexamethylene diisocyanate (HMDI) or tolylene 2,4‐diisocyanate (TDI) with a mixture of Ca(HEEP)₂ and poly(ethylene glycol) (PEG₃₀₀ or PEG₄₀₀) with di‐n‐butyltin dilaurate as a catalyst. A series of calcium‐containing PUEs of different compositions were synthesized with Ca(HEEP)₂/PEG₃₀₀ (or PEG₄₀₀)/diisocyanate (HMDI or TDI) molar ratios of 2:2:4, 3:1:4, and 1:3:4 so that the coating properties of the PUEs could be studied. Blank PUEs without calcium‐containing ionic diols were also prepared by the reaction of PEG₃₀₀ or PEG₄₀₀ with HMDI or TDI. The PUEs were well characterized by Fourier transform infrared, ¹H and ¹³C NMR, solid‐state cross‐polarity/magic‐angle‐spinning ¹³C NMR, viscosity, solubility, and X‐ray diffraction studies. The thermal properties of the polymers were also studied with thermogravimetric analysis and differential scanning calorimetry. The PUEs were applied as top coats on acrylic‐coated leather, and their physicomechanical properties were also studied. The coating properties of PUEs, such as the tensile strength, elongation at break, tear strength, water vapor permeability, flexing endurance, cold crack resistance, abrasion resistance, color fastness, and adhesive strength, were better than the standard values. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 2865–2878, 2003     

Microstructure and high-temperature wear resistance of a laser surface alloyed γ-TiAl with carbon

TiC reinforced composite coating on γ-TiAl alloy was successfully fabricated by laser surface alloying with carbon. The fine TiC reinforcing phase had a gradient distribution in the coating, and its growth morphology of TiC in laser surface alloyed coating was in unique faceted platelet-like. The composite coating exhibited high hardness and excellent high-temperature sliding wear resistance.     

Bi12TiO20纳米粉体的制备及其光吸收特性研究

以钛酸四丁酯和硝酸铋为原料 ,利用化学溶液分解法制备了Bi12 TiO2 0 纳米多晶粉体 .采用XRD和TEM对其结构和形貌进行了表征 .结合热重 差热 (TG DTA)分析 ,探讨了Bi12 TiO2 0 晶相的形成机理 .通过UV Vis漫反射谱的测定 ,研究了Bi12 TiO2 0 纳米晶粉体的光吸收特性 .结果显示 ,从组成为化学计量比的前驱液中可以很容易制得纯Bi12 TiO2 0 纳米晶粉体 ,该Bi12 TiO2 0 纳米晶粉体呈现了在很宽的波长范围内 (5 6 0～ 385nm )对光的吸收的特性 .     

光学薄膜在现代汽车工业中的应用

本文论述应用光学薄膜技术对汽车窗口玻璃和塑料的若干性能进行改进的技术发展水平，这些性能包括塑料表面的硬化，红外区的反射，紫外区的吸收，偏振化作用，双折射，憎水性以及光学角度选择性等，评论等离子体处理和物理蒸汽淀积薄膜工艺近来应用的一些例子。对于物理蒸汽淀积薄膜所提供的异常功能连同实际使用中它们的耐久性作了特殊的强调。     

塑料光学元件的清洗、镀膜和胶合

各种塑料光学元件在光学系统中的应用越来越广泛。作为光学元件,必然涉及清洗、镀膜和胶合等工艺技术问题。本文就塑料光学元件的这三个技术作一介绍。