室温交联型硅丙微胶乳的合成研究(1)硅烷单体对聚合稳定性和胶膜性能的影响

采用种子微乳液聚合工艺和单体半连续滴加法合成了室温交联型有机硅改性丙烯酸酯微胶乳，研究了硅烷单体种类和用量及其添加顺序等对聚合稳定和胶膜性能的影响。结果表明，使用含阻碍性铁新硅烷单体（C－1757）可明显抑制体系中的水解－缩合反应，提高聚合稳定性，而且随其用量增加，改性胶膜的交联密度增大，拉伸强度提高；延迟添加C－1757，可进一步提高聚合稳定性，但会降低胶膜的交联密度，拉伸强度先高后低，30／70处有一个最大值，所合成的硅丙微胶乳储存期可达长两年，与C－1757相比，硅烷单体A－174改性的胶膜具有更大的交联密度，而A－171改性的胶膜交联密度偏低，力学性能较差。     

室温交联型硅丙微胶乳的合成研究Ⅲ.聚合工艺对聚合稳定性及胶膜性能的影响

采用两种聚合工艺(种子微乳液聚合法和单体预乳化法)分别合成了室温交联型有机硅改性丙烯酸酯聚合物微胶乳，研完了不同工艺条件对聚合稳定性、乳胶粒径和胶膜的结构性能的影响．     

Kinetics of polymerization of styrene-in-water microemulsions

The kinetics of polymerization of styrene-in-water microemulsions was investigated using dilatometry. From plots of percentage conversion versus time, the rate of polymerization, R _p, was determined. From log-log plots of R _p versus styrene and initiator [2,2′-azobis(isobutyronitrile), AIBN] concentrations the following relationship was established: R _p∝ [styrene]^1.2 [AIBN]^0.46. These exponents are similar to those predicted by the theory of emulsion polymerization. The results also showed a rapid conversion in the initial period (interval 1) followed by a slower rate at longer times (interval 2). It was suggested that in interval 1, the main process in nucleation of the microemulsion droplets, whereas in interval 2 propagation is the more dominant factor. The rapid polymerization of microemulsions is consistent with their structure, whereby very small droplets with flexible interfaces are produced. Received: 2 March 1999 Accepted in revised form: 10 May 1999     

室温交联型硅丙微胶乳的合成研究II.改性微胶乳的粒径控制及其微观形态表征

采用种子微乳液聚合法和单体预乳化法分别合成了室温交联型有机硅改性聚丙烯酸酯微胶乳,研究了硅烷单体的添加和氨化反应对改性微胶乳粒子大小及分布的影响。结果表明:采用种子微乳液聚合法得到的硅丙微胶乳粒子大小与硅烷单体的种类、用量和添加顺序无关,平均粒径约为40~60nm。TEM照片显示出,采用种子微乳液聚合法合成的硅丙微胶乳粒子由于内部存在交联结构而导致表面形状不规则,有“乳突”现象;而采用预乳化法合成的硅丙微胶乳粒径粗大,呈规则的球形,氨化后粒径从100nm以上减小到80nm左右,粒子表面出现“绒毛”现象,这是由于硅烷组分的水解反应受到抑制而使粒子内部的交联密度降低的缘故。