Structure and properties of the mesophase of syndiotactic polystyrene. VIII. Solvent sorption behavior of syndiotactic polystyrene/p‐chlorotoluene mesophase membranes

A crystalline δ form of a syndiotactic polystyrene (sPS) membrane was prepared from a solution of sPS (1 wt %) and p‐chlorotoluene (p‐CT) by a solution‐casting method. The mesophase (δ empty form) of sPS was obtained by the extraction of the guest solvent from the δ form of sPS by a stepwise solvent‐extraction method. The sPS/p‐CT mesophase membrane [p‐CT (A‐M)] was used for the sorption of 1 mol % p‐CT for different times and for the sorption of different concentrations of p‐CT, chlorobenzene (CB), p‐xylene (p‐X), toluene, and chloroform for 48 h. The presence of solvents in the sPS membrane was confirmed by IR analysis. A thermal study revealed that the sorption amount of 1 mol % p‐CT increased with increasing immersion time, and the sorption amounts of different solvents increased with increasing solvent concentration. Differential scanning calorimetry results showed that the desorption peak temperature increased as the amount of the solvent increased in the clathrated sPS membrane. Wide‐angle X‐ray diffraction results showed that 2θ at 8.25° was slightly shifted toward 8°, and there was no change in the peak position at 10° for p‐CT (A‐M), which was immersed in different solvents (1 mol %); however, the intensity of 2θ at 10° was not similar for all the samples. Among the solvents used for the sorption studies at 1 mol %, p‐CT (A‐M) could sorb more p‐CT and CB than p‐X, toluene, and chloroform. The solvent sorption isotherm was the Langmuir sorption mechanism. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 3439–3446, 2004     

Deconvolution of very low primary energy SIMS depth profiles

In this paper, the deconvolution of SIMS profiles analysed at very low primary energy (0.5 keV/O₂⁺) is addressed. The depth resolution function (DRF) of the SIMS analysis in presence of roughness is established and a deconvolution procedure is implemented without or in presence of roughness on samples containing delta-doped layers of boron in silicon. It is shown that the deconvolution procedure can lead to a great improvement of the full width at half maximum (FWHM) of the measured peaks in the case where no roughness in detected in the crater bottom. In the case where it is present, the conditions required to use a deconvolution procedure are discussed, and the deconvolution is implemented using precise and restrictive assumptions.     

Growth kinetics of iron boride layers: Dimensional analysis

Dimensional analysis is presented as a powerful tool in the study of the paste boriding process. In particular, a dimensional method is used to study the growth kinetics of the boride layers FeB and Fe₂B. Experiments were performed in AISI 1045 steel and AISI M2 steel, to test the suggested model. Samples of 1045 steel were prepared and treated using boron paste thickness of 3-5 mm, at temperatures of 1193, 1223 and 1273 K, with 2, 4 and 6 h of treatment time. The M2 specimens had boron paste thickness of 3 and 4 mm and temperatures of 1223, 1253 and 1273 K for 2 and 6 h. Results indicate that the growth of boron layers obeys power laws of the form y = αx^β, where α and β constants are a function of the material and the interface of interest. Validation of the model was carried out using experimental data with an average error percentage of 7.6% for Fe₂B in 1045 steel, 15.8% for FeB and 3.4% for Fe₂B in M2 steel.     

On the solution of Falkner-Skan equations

New existence and uniqueness proofs are given for the solutions of the equations governing the self-similar compressible boundary layer (Falkner-Skan equations). The properties of the solutions are studied and some bounds on important quantities are concluded. The paper is restricted to favourable pressure gradients and to wall cooling.     

水准折光及双波长激光效应

本文从“同温度层不完全平行于地面,且在变化”的“任意分层”假设出发,导出了水准折光修正公式,并利用光的色散效应在10~(-6)的精度要求下,求得r=r_T=h_1/h_2=(n_(01)-1)/(n_(02)-1)=常数最后指出,研制双波长激光水准仪的必要性和可能性,并提出了研制此种仪器的技术参数.     

Characterization of some essential oils and their key components: Thermoanalytical techniques

The present study was aimed at determining the kinetics of evaporation and establishing vapor pressure curves for both single and multi-component systems by thermogravimetry (TG) and differential scanning calorimetry (DSC). Essential oils (e.g. lavender oil, orange oil, clove oil and eucalyptus oil, etc.) are typically multi-component systems consisting of various volatile pure components (e.g. linalyl acetate, limonene, cinnamaldehyde, etc.) which resemble single component systems. In this study linalyl acetate was taken as the calibration compound for TG. The vapor pressure curves for the pure substances were plotted using TG and vapor pressure plots for clove oil and eucalyptus oil were constructed using DSC. The thermodynamic and kinetic parameters of the pure compounds were compared to that of the multi-component systems to quantitatively and qualitatively measure the influence of different compounds on each other. The k-value from the vapor pressure data for linalyl acetate was calculated as 112006 Pa kg^0.5mol^0.5s^-1 m^-2 K^-0.5. The vapor pressure values were used to determine the Antoine constants using the SPSS 10.0 software.This revised version was published online in November 2005 with corrections to the Cover Date.     

Multilayered Cu–Ti deposition on silicon substrates for chemiresistor applications

Abstract

On the perspective to develop CuO–TiO₂ MOS, multilayered Cu and Ti thin layers were alternatively deposited on silicon wafers using 25?keV Ar?+?ion beam sputtering and, subsequently, oxidized by thermal annealing in air at 400?°C for 24?h. The deposited films have variable ratios of the Cu and Ti % at. One of the main goal is to obtain such multilayers avoiding the presence of Cu–Ti–O compounds. The samples were characterized in terms of composition (by RBS and SIMS analyses) and morphology (by AFM and SEM investigations). In particular, SIMS maps allows to observe the spatial distribution and thickness of each phase of the Cu/Ti multilayers, and further to observe Cu diffusion and mixing with Ti, as well as phase separation of CuO and TiO₂ in the samples. The reasons of this effect represent an open issue that has to investigated, in order to improve the MOS fabrication.     

Deposition and characterization of Langmuir‐Blodgett films of cadmium arachidate/SWCNTs composites

The incorporation of single‐wall carbon nanotubes (SWCNTs) in cadmium arachidate film by means of the Langmuir‐Blodgett (LB) technique was investigated as a function of arachidic acid/SWCNT mass ratio at the air/water interface and in Langmuir‐Blodgett films. The behaviour at the air/water interface shows that SWCNTs act as an independent phase with respect to the cadmium arachidate. Deposition conditions are optimized when the weight ratio between the arachidic acid (AA) and SWCNTs is in the range 0.018:1 to 1:1. The general order of the LB multilayered structure was destroyed by the progressive density increase in SWCNT quantity as evidenced by X‐ray reflectivity (XRR) analysis. Scanning electron microscopy images indicated that when a multilayered structure was formed its layers consisted of SWCNT bundles stacked one over the other. Copyright © 2006 John Wiley & Sons, Ltd.     

6AZO-CONTAINING SELF-ASSEMBLY ULTRA-THIN FILMS AND THEIR PHOTOVOLTAIC PROPERTIES

A kind of azo-containing resin (Azo-R) was synthesized by a simple way through the coupling reaction of 2-nitro-N-methyldiphenylamine-4-diazoresin (NDR) with phenol, and a new covalentely attached multilayer film from Azo-R as H-donor and photosensitive diazoresin, diphenylamine-4-diazoresin (DR) as H-acceptor via H-bonding attraction by selfassembly technique has been fabricated. Following the decomposition of diazonium group of DR under exposure to UV light, the H-bonds between the layers of the film convert to covalent bonds and the film becomes very stable toward polar solvents or electrolyte aqueous solutions. Thus the UV-irradiated azo-containing films can be used to measure photocurrent in a conventional three-electrode photoelectrochemical cell using KCl as supporting electrolyte. It was confirmed that the azo-containing multilayer film is responsible for the photocurrent generation.     

Infrared dichroism measurements on the alkyl chain packing of an ionic detergent intercalated between silicate layers

 Microcrystals of the metal silicate hydrate ilerite orient macroscopically on the surface of a ATR-crystals and thus, are accessible for infrared linear dichroism measurements. We present first results which indicate that the alkyl chain packing and the orientation of the polar group of dodecyltrimethylammoniumbromide (DTAB) intercalated between silicate layers can be determined in terms of infrared order parameters. The properties of DTAB can be modulated by the relative humidity of the surrounding atmosphere and by temperature. Upon heating DTAB undergoes a phase transition from a paraffin-like solid to a fluid phase. The former is characterized by the orthorhombic perpendicular packing of the frozen alkyl chains with tilted long axes. The interactions between the ionic groups of the surfactant and that of the host matrix stabilize the lamellar arrangement of DTAB in the crystalline and in the fluid phases. Received: 14 January 1998 Accepted: 27 July 1998