Identification of chlorinated sulfur compounds in pulp mill effluents by GC-MS and GC-AED

Summary Three chlorinated dimethyl sulfones and five chlorinated thiophenes have been identified in the alkaline extraction liquor from a bleach plant by gas chromatography with atomic emission detection (GC-AED) and with mass spectrometry (GC-MS). The information on elemental content obtained by GC-AED enabled a rapid screening of the sulfur compounds and provided important structural information complementary to the mass spectral data. Quantitation was accomplished by GC-AED based on universal calibration.     

Enhancing the enzymatic hydrolysis of cellulosic materials using simultaneous ball milling

One of the limiting factors restricting the effective and efficient bioconversion of softwood-derived lignocellulosic residues is the recalcitrance of the substrate following pretreatment. Consequently, the ensuing enzymatic process requires relatively high enzyme loadings to produce monomeric carbohydrates that are readily fermentable by ethanologenic microorganisms. In an attempt to circumvent the need for larger enzyme loadings, a simultaneous physical and enzymatic hydrolysis treatment was evaluated. A ball-mill reactor was used as the digestion vessel, and the extent and rate of hydrolysis were monitored. Concurrently, enzyme adsorption profiles and the rate of conversion during the course of hydrolysis were monitored. α-Cellulose, employed as a model substrate, and SO₂-impregnated steam-exploded Douglas-fir wood chips were assessed as the cellulosic substrates. The softwood-derived substrate was further posttreated with water and hot alkaline hydrogen peroxide to remove >90% of the original lignin. Experiments at different reaction conditions were evaluated, including substrate concentration, enzyme loading, reaction volumes, and number of ball beads employed during mechanical milling. It was apparent that the best conditions for the enzymatic hydrolysis of α-cellulose were attained using a higher number of beads, while the presence of air-liquid interface did not seem to affect the rate of saccharification. Similarly, when employing the lignocellulosic substrate, up to 100% hydrolysis could be achieved with a minimum enzyme loading (10 filter paper units/g of cellulose), at lower substrate concentrations and with a greater number of reaction beads during milling. It was apparent that the combined strategy of simultaneous ball milling and enzymatic hydrolysis could improve the rate of saccharification and/or reduce the enzyme loading required to attain total hydrolysis of the carbohydrate moieties.     

Development of a laccase-based flow injection electrochemical biosensor for the determination of phenolic compounds and its application for monitoring remediation of Kraft E1 paper mill effluent

This paper describes the development of a new system for amperometric determination of phenolic compounds, and its application for monitoring these compounds in paper mill effluent. The method was based on a flow system, a dialysis sampler, and a laccase-based biosensor. The performance of this system was investigated with respect to pH, ionic strength, working potential, and flow-rate dependence. The biosensor showed an excellent long-term stability allowing measurements for over than 3 months. The sensitivity of laccase-based biosensor was tested for phenol, p-chlorophenol, guaiacol and chloroguaiacol; the detector presented selective measurements of micromolar concentration of these compounds. The integration of a dialysis membrane sampling in the system protected the biosensor surface from fouling and gave independence of sample conditions that commonly influence the biosensor performance. These favorable characteristics allowed its application for direct measurements in complex media with no sample pretreatment. This ability was confirmed employing this system in a continuous analysis of phenolic compounds during the remediation of paper mill effluent by ozonization process.     

Application of DEM modified with enlarged particle model to simulation of bead motion in a bead mill

We applied the discrete element method （DEM） of simulation modified by an enlarged particle model to simulate bead motion in a large bead mill. The stainless-steel bead mill has inner diameter of 102 mm and mill length of 198 mm. The bead diameter and filling ratio were fixed respectively at 0.5 mm and 85%. The agitator rotational speed was changed from 1863 to 3261 rpm. The bead motion was monitored experimentally using a high-speed video camera through a transparent mill body. For the simulation, enlarged particle sizes were set as 3-6 mm in diameter. With the DEM modified by the enlarged particle model, the motion of enlarged particles in a mill was simulated.The velocity data of the simulated enlarged particles were compared with those obtained in the experiment. The simulated velocity of the enlarged particles depends on the virtual frictional coefficient in the DEM model. The optimized value of the virtual frictional coefficient can be determined by considering the accumulated mean value. Results show that the velocity of the enlarged particles simulated increases with an increase in the optimum virtual frictional coefficient, but the simulated velocity agrees well with that determined experimentally by optimizing the virtual frictional coefficient in the simulation. The computing time in the simulation decreases with increased particle size.     

Synergetic catalytic effect of rGO,Pd, Fe3O4 and PPy as a magnetically separable and recyclable nanocomposite for coupling reactions in green media

In this paper, rGO/Pd–Fe₃O₄@PPy as an efficient stable nanocomposite was synthesized. To understand the synergetic effects of rGO, Pd, Fe₃O₄ and PolyPyrrole, the performance of rGO/Pd–Fe₃O₄@PPy as a heterogeneous recyclable nanocatalyst in the green synthesis of C‐C and C‐O coupling products, as well as different conditions are studied. Synthesized rGO/Pd–Fe₃O₄@PPy was characterized by FT‐IR, XRD, FE‐SEM, EDS, TGA and AFM analysis. Best results are obtained under sonication in H₂O for C‐C coupling and by ball‐milling for C‐O coupling. The benefits of this method include: green solvents and conditions, absence of external base, low reaction times with high yield and easy work‐up method.     

Effects of ball-to-powder diameter ratio and powder particle shape on EDEM simulation in a planetary ball mill

The effects of the ball-to-powder diameter ratio (BPDR) and the shape of the powder particles on EDEM simulation results and time in the planetary ball mill was investigated. BPDR was varied from 1 to 40/3 by changing the powder particle diameter from 8 to 0.6 ?mm. The size and shape of the powder particles do not give a significant change in both the ball motion pattern and simulation results when BPDR is over 20/3. It can be assumed that the kinetic energy of the ball has nothing to do with the size and shape of the powder particle. The simulation time and data size increase exponentially as BPDR increases. The effect of change of the powder particle shape on the calculated data size is not significant, but the more complicated its shape, the longer the simulation time, which is linearly related to the number of spheres composing a particle.     

Enhanced Physical and Mechanical Properties of Nitrile-Butadiene Rubber Composites with N-Cetylpyridinium Bromide-Carbon Black

The physical and mechanical properties of nitrile–butadiene rubber (NBR) composites with N-cetylpyridinium bromide-carbon black (CPB-CB) were investigated. Addition of 5 parts per hundred rubber (phr) of CPB-CB into NBR improved the tensile strength by 124%, vulcanization rate by 41%, shore hardness by 15%, and decreased the volumetric wear by 7% compared to those of the base rubber-CB composite.     

酸枣果肉中挥发性化学成分的提取及分析

报道了用蒸馏-萃取法和同时蒸馏-萃取法提取酸枣果肉中挥发性物质,测得两种方法提取的酸枣果肉挥发油含量分别为1．80％和2．30％。用GC／MS法从酸枣果肉挥发油中分别分离并确定出43种和28种化学成分,分别占酸枣果肉挥发油总检出量的95．62％和94．88％。用峰面积归一化法通过化学工作站数据处理系统,得出各化学成分在挥发油中的相对百分含量。     

原子荧光光谱法测定固体废弃物——氧化皮中的砷

建立了固体废弃物——氧化皮中砷的测定方法。氧化皮粉末样品经盐酸溶解,在溶液中添加硫脲和抗坏血酸预还原砷,以盐酸(2+98)为载流,硼氢化钠(10g/L)和氢氧化钾(5g/L)混合溶液为还原剂,砷与硼氢化钠、盐酸反应生成砷化氢,砷化氢利用氩气导入石英炉原子化器中原子化,以空心阴极灯为激发光源,测量砷产生的荧光强度。测试氧化皮中砷含量的相对标准偏差为不大于4.8%,检出限为0.12μg/L,回收率为97%～103%,结果准确度较好。方法具有试剂消耗少、快速、检出限低的优点。     

Biosynthesis and characterization of poly(3-hydroxybutyrate-co-3-hydroxyvalerate) copolymer from wild-type Comamonas sp. EB172

Poly(3-hydroxybutyrate) [P(3HB)] homopolymer and poly(3-hydroxybutyrate-co-3-hydroxyvalerate) [P(3HB-co-3HV)] copolymer was produced by Comamonas sp. EB172 using single and mixture of carbon sources. Poly(3-hydroxyvalerate) P(3HV) incorporation in the copolymer was obtained when propionic and valeric acid was used as precursors. Incorporation of 3HV fractions in the copolymer varied from 45 to 86 mol% when initial pH of the medium was regulated. In fed-batch cultivation, organic acids derived from anaerobically treated palm oil mill effluent (POME) were shown to be suitable carbon sources for polyhydroxyalkanoate (PHA) production by Comamonas sp. EB172. Number average molecular weight (M_n) produced by the strain was in the range of 153-412 kDa with polydispersity index (M_w/M_n) in the range of 2.2-2.6, respectively. Incorporation of higher 3HV units improved the thermal stability of P(3HB-co-3HV) copolymer. Thus the newly isolated bacterium Comamonas sp. EB172 is a suitable candidate for PHA production using POME as renewable and alternative cheap raw materials.