On the Fundamental Polymer Chemistry of Inverse Vulcanization for Statistical and Segmented Copolymers from Elemental Sulfur

In this concept review, the fundamental and polymerization chemistry of inverse vulcanization for the preparation of statistical and segmented sulfur copolymers, which have been actively developed and advanced in various applications over the past decade is discussed. This concept review delves into a discussion of step-growth polymerization constructs to describe the inverse vulcanization process and discuss prepolymer approaches for the synthesis of segmented sulfur polyurethanes. Furthermore, this concept review discusses the advantages of inverse vulcanization in conjunction with dynamic covalent polymerization and post-polymerization modifications to prepare segmented block copolymers with enhanced thermomechanical and flame retardant properties of these materials.     

A simple,rapid and sensitive method based on modified multiwalled carbon nanotube for preconcentration and determination of lead ions in aqueous media in natural pHs

In this study, multiwalled carbon nanotube (MWCNT) was modified by the pyridine group using a silane agent and characterized by infrared spectroscopy (IR), thermal analysis (TG/DTA), and elemental analysis (CHN) and scanning electron microscopy (SEM). The application of this sorbent was investigated in determination of lead ions in aqueous samples, using flame atomic absorption spectrometry (FAAS). Through this study, different parameters such as pH and sample flow rate on adsorption process and eluent concentration, volume and flow rate were optimized. The limit of detection (LOD), the relative standard deviation and the recovery of the method were 2 ng mL^?1, 1.3% and 99.7%, respectively. Two standard reference materials (NIST 1571 and NIST 1572) were used to verify accuracy of this method. Finally, the sorbent was successfully applied for extraction and determination of low levels of Pb(II) ions in aqueous samples.     

原子吸收光谱法测定铝锂合金中锂

本文研究了用原子吸收光谱法在笑气－乙炔火焰中测定铝锂合金中锂的最佳条件。其电离干扰可通过加进钾进盐来控制。应用本法测定合金中 锂的含量，获得了满意结果。     

离子交换富集-导数火焰原子吸收法测定自来水中Cu,Fe和Zn

本文研究了用 2 0 1× 7阳离子交换树脂对自来水中的微量元素进行交换富集 ,采用微量脉冲进样 导数火焰原子吸收法测定富集后溶液中的Cu ,Fe和Zn ,该方法灵敏度分别为 0 2 9,0 5 9和 0 0 6 μg·L- 1 ,精密度分别为 4 2 8% ,1 95 %和 2 2 8% ,检测限分别为 1 2 8,5 85和 0 6 8μg·L- 1 ,回收率分别为 91 13% ,10 1 34%和99 84 % ,本方法大大减少了需样量 ,简便快速 ,灵敏度高。     

Atomic distributions in acetylene-air flame using hydraulic high-pressure nebulization with direct (100%) introduction of solutions Applications to speciation analysis

One of the fundamental factors of the performance of atomic spectrometric methods is the efficiency of sample introduction into flame or plasma. By utilization of the formerly developed hydraulic high-pressure nebulizer, a nebulizer/burner system with solution uptake efficiency of 100% have been worked out. Optimizing operation parameters of nebulizer/burner system, an improvement of 2-12 times was achieved for the signal-to-noise ratio in the flame emission and flame atomic absorption spectrometry, depending on sample flow rate. This nebulizer is especially suitable for development of liquid chromatography-AAS/FES coupled technique for speciation analytical tasks.     

火焰原子吸收法测定霞石中的氧化钾和氧化钠

本方法用于测定霞石中的钾、钠，主要通过在溶样时加入氢氟酸除去二氧化硅，调整溶液中钾、钠的含量，消除互相之间的干扰，加入氯化铯消除电离因素的干扰，提高了分析结果的准确性和重现性，使测定结果更接近化学分析值。回收率为99．2％-101．6％。     

Simulation of a turbulent premixed open V-shaped flame using contour advection with surgery

Despite its capability of high spatial resolution, simulation of turbulent flows with traditional Lagrangian (front tracking) scheme is often discouraged by numerical instability caused by clustering of marker nodes and topological changes of fronts. Contour advection surgery (CAS), being a robust front tracking scheme, can limit the growth of front complexity during simulation without jeopardizing accuracy or efficiency. This allows it to open up an advantage over traditional front-tracking schemes. It has already been demonstrated that CAS, with incorporation of the reaction sheet model, can accurately simulate the propagation and advection of a turbulent premixed V-shaped flame. In this study, it is further tested with 10 values of vortex circulation. A range of upstream turbulence levels of 1.8–19.8% was obtained. Results indicate that upstream turbulence increase the average flame length, flame zone area and the overall burning rate. Flame surface density Σ was also estimated. Maximum values of Σ obtained lie in the range 0.1–1.4 mm⁻¹. Skewness towards the burnt region was observed in all profiles of Σ. Similar to results from laboratory experiments, it was found that Σ values decreases with upstream turbulence. From this study, the ability of CAS to cope with intense turbulence is demonstrated and a better quantitative understanding on the scheme has also been acquired.     

Determination of the boiling point distribution of sulfur compounds in light cycle oil using GC with a flame photometric detector and pyrolyzer

A method has been developed to determine the boiling point distribution of sulfur compounds in light cycle oils (LCO'S). The method chosen for this analysis was GC with a flame photometric detector (FPD) and pyrolyzer. Tests were carried out to evaluate the recovery efficiency, repeatability, and accuracy of the method. Repeatabilities within 2% were obtained. The recovery of benzothiophenes and dibenzothiophenes was close to 100%; this was important because these are the major sulfur components in LCO's. No hydrocarbon or solvent interferences were observed with the use of the pyrolyzer, even for a 95% solvent level. Comparison with results from other techniques showed that the method accurately determined the levels of sulfur compounds in the LCO boiling point range.     

Thermal properties of poly(styrene) containing brominated aryl phosphate additives

General purpose poly(styrene) is a large volume commodity polymer widely used in a range of applications. For many of these the presence of an additive to impart some flammability resistance is required. Most commonly, brominated aromatics are used for this purpose. As the polymer undergoes combustion these compounds decompose to generate bromine atoms and/or hydrogen bromide which escape to the gas phase and trap flame propagating radicals. While these species are effective in inhibiting flame propagation they present the opportunity for loss of halogen to the atmosphere. For this reason, the use of these compounds is being limited in some parts of the world. Phosphorus compounds, on the other had, impart a flame retarding influence by promoting char formation at the surface of the burning polymer. This prevents heat feedback to the polymer and consequent pyrolysis to generate fuel fragments. The combination of both bromine and phosphorus present in a single compound might generate a superior flame-retarding additive in that both modes of retardancy might be promoted simultaneously. Should this be the case smaller amounts of additive might be necessary to achieve a satisfactory level of flame retardancy. A series of such additives, brominated aryl phosphates, has been synthesized and fully characterized spectroscopically. Blends of these additives, at various levels, with poly(styrene) have been examined by DSC, TG and in the UL-94 flame test. The flammability of the polymer is dramatically diminished by the presence of the additive.     

原子吸收光谱法测定铬基合金中钒

本文研究了用原子吸收光谱法，在笑气－乙炔火焰中，测定钒的最佳条件，不用任何分离手段，以铝盐做干扰抑制剂，消除铬，镍对测定钒的干扰，西方法用于铬基合金中钒的测定，方法简单准确，具有实用意义。