数字喷墨印刷关键技术及其实现

经过20多年的完善与发展，喷墨技术已经成为大幅面广告印刷行业的主要印刷技术。随着图书按需印刷需求的快速扩张以及国家环保政策的迅速落地，喷墨印刷技术作为一项高效环保的数字化印刷技术，得到越来越高的关注，业内普遍认为喷墨印刷技术将是数字化印刷的必然发展趋势。然而与已经成熟的多Pass喷墨印刷设备不同，单Pass喷墨印刷设备在数据带宽、数据在线重构、高精度同步控制、喷嘴在线补偿等方面有着极高的技术要求。本文首先简要介绍了喷墨技术，然后针对单Pass喷墨印刷设备需要解决的技术问题提出了相应的解决方案。依据本文技术设计的单Pass书刊喷墨印刷机已经投放市场，并且获得了用户的普遍认可。     

连续臂丛神经阻滞镇痛对断指再植血流动力学影响的研究

目的研究连续臂丛神经阻滞镇痛对断指再植术后再植指血流动力学的影响，探讨其缓解血管痉挛、增加血流量的可行性。方法将60例急诊行断指再植术患者按随机数字表法分为术后连续臂丛神经阻滞镇痛组（CA组）和对照组（NA组），每组30例。观察两组患者再植指术后血管痉挛、血管栓塞和指体坏死发生例数并计算再植指成活率，记录两组术后即刻（T1）、术后24h（T2）再植指固有动脉血流动力学参数及动脉内径（AD）、远指端血氧饱和度（SpO2）和温度（Ts）变化。结果断指再植术后成活率CA组高于NA组，血管痉挛、血管栓塞和指体坏死发生率CA组均低于NA组，差异均有统计学意义（均P＜0.05）。在T2时CA组各项血流动力学参数、AD、SpO2、Ts均高于NA组，阻力指数（RI）低于NA组，差异均有统计学意义（均P＜0.05）。结论术后连续臂丛神经阻滞镇痛可以缓解再植指固有动脉痉挛，增加指体血流量，提高了断指再植的成功率。     

Quantitative analysis of asymmetrical cortical activity in motor areas during sequential finger movement

Brain asymmetry is a phenomenon well known for handedness and has been studied in motor cortices. However, few quantitative studies on asymmetrical cortical activity in motor areas have been conducted. In this study, we systematically investigated asymmetrical cortical activity in motor areas during sequential finger movement by quantitatively analyzing functional magnetic resonance imaging (fMRI) blood oxygenation level-dependent (BOLD) responses. The norm of BOLD signal percentage of change was introduced to quantitatively measure the BOLD signal intensity change difference between the left and right motor areas. The results of the data collected from six subjects show that the norm of BOLD signal percentage of change in the right motor area is higher than that in the left motor area for two-hand movement (P=.0059) and single-hand movement (P=.0279) with right-handedness. These results from fMRI show the asymmetry of motor areas and may suggest that the left hemisphere motor area comes into being as an adaptation system that needs few neuron cells only to finish any movement task for right-handedness. The activation intensity in the left motor area is reduced with normal right finger movement. The activation intensity in the right motor area is obviously higher than that in the left motor area.     

n型IBC太阳电池选择性发射极工艺研究

为提升n型叉指背接触(IBC)太阳电池的光电转换效率,采用丝网印刷硼浆和高温扩散的方式形成选择性发射极结构,研究了硼扩散和硼浆印刷工艺对电池发射极钝化性能和接触性能的影响。实验结果表明,在硼扩散沉积时间和退火时间一定的条件下,硼扩散通源(BBr₃)流量为100 mL/min,沉积温度为830 ℃,退火温度为920 ℃时,发射极轻掺杂(p⁺)区域的隐开路电压达到710 mV,暗饱和电流密度为12.2 fA/cm²。发射极局部印刷硼浆湿重为220 mg时,经过高温硼扩散退火,重掺杂(p⁺⁺)区域的隐开路电压保持在683 mV左右,该区域方块电阻仅46 Ω/□,金属接触电阻为2.3 mΩ·cm². 采用该工艺方案制备的IBC电池最高光电转换效率达到24.40%,平均光电转换效率达到24.32%,相比现有IBC电池转换效率提升了0.28个百分点。     

Laser printing of enamels on tiles

A Nd:YAG laser beam is used as a tool to print patterns of coloured enamels on tile substrates. For this, the laser beam is scanned over a layer of raw enamel previously sprayed on the tile surface. The possibility to focus the laser energy to heat a small zone without affecting the rest of the piece presents some advantages in front of traditional furnace techniques in which the whole piece has to be heated; among them, energy saving and the possibility to apply enamels with higher melting temperatures than those of the substrate. In this work, we study the effects of laser irradiation of a green enamel, based in chromium oxide pigment and lead frit, deposited on a white tile substrate. Lines obtained with different combinations of laser beam power and scan speeds were investigated with the aim to optimize the process from the point of view of the quality of the patterns. For this purpose, the morphology of the lines and their cross-sections is studied. The results show that lines with good visual properties can be printed with the laser. The characteristics of the marked lines were found to be directly related with the accumulated energy density delivered. Moreover, there is a linear relationship between the accumulated energy density and the volume of melted material. A minimum accumulated energy density is required to melt a shallow zone of the glazed substrate to allow the adhesion of the enamelled lines.     

Direct numerical simulations of two-layer viscosity-stratified flow

Two-dimensional simulations of flow instability at the interface of a two-layer, density-matched, viscosity-stratified Poiseuille flow are performed using a front-tracking/finite difference method. We present results for the small-amplitude (linear) growth rate of the instability at small to medium Reynolds number for varying thickness ratio n, viscosity ratio m, and wavenumber. We also present results for large-amplitude non-linear evolution of the interface for varying viscosity ratio and interfacial tension. For the linear case, the interfacial mode is neutrally stable for as predicted by analysis. The growth rate is proportional to Reynolds number for small Re, and increases with viscosity ratio. The growth rate also increases when the thickness of the more viscous layer is reduced. Strong non-linear behavior is observed for relatively large initial perturbation amplitude. The higher viscosity fluid is drawn out as a finger that penetrates into the lower viscosity layer. The simulated interface shape compares well with previously reported experiments. Increasing interfacial tension retards the growth rate of the interface as expected, whereas increasing the viscosity ratio enhances it. Drop formation at the small Reynolds number considered in this study is precluded by the two-dimensional nature of the calculations.     

Selection in the Saffman-Taylor finger problem and the Taylor-Saffman bubble problem without surface tension

We consider the Saffman-Taylor problem describing the displacement of one fluid by another having a smaller viscosity, in a porous medium or in a Hele-Shaw configuration, and the Taylor-Saffman problem of a bubble moving in a channel containing moving fluid. Each problem is known to possess a family of solutions, the former corresponding to propagating fingers and the latter to propagating bubbles, with each member characterized by its own velocity and each occupying a different fraction of the porous channel through which it propagates. To select the correct member of the family of solutions, the conventional approach has been to add surface tension σ and then take the limit σ → 0. We propose a selection criterion that does not rely on surface tension arguments.     

Shared value in a finite-dimensional Banach manifold

Sufficient conditions are given to assert that two C¹-mappings share only one value in a connected compact Banach manifold modelled over ?ⁿ. The proof of the result, which is based upon continuation methods, is constructive.     

半色调双面图像的色彩预测Clapper-Yule模型

为了准确地预测印刷图像的光谱反射率,在假定油墨是非散射介质以及油墨的折射率与纸张的折射率近似相等的近似下,利用考虑光在纸基内多次内反射的Clapper-Yule理论和描述多重内反射的网状结构分析模型,建立了同色不同加网周期双面墨像的光谱反射色彩预测模型.同时给出了包含纸基的向下体反射和反面纸基-空气构成界面定向反射作用的单面墨像Clapper-Yule色彩预测修正新模型.     

HL-2M 环向场线圈水冷数值模拟与分析

建立了环向场线圈的水冷计算模型,根据热传导和对流换热方程进行了数值模拟分析。计算结果表明：指形接头与铜板的界面接触热阻和接触电阻对指形接头的温升影响较大,但在平顶电流为140kA 及其电流平顶7s 时,由焦耳热引起的最高温升40℃以下,故环向场线圈的温度均不会超过80℃,且15min 后TF 线圈温度均降至30℃以下。在平顶电流为190kA 时,线圈通电持续时间可根据界面实测接触热阻、接触电阻以及线圈初始温度来确定。