ENR-25改性CaCO3填充LDPE的复合材料的研究

用环氧程度为25％的环氧化天然橡胶（ENR－25）改性轻质CaCO3。研究了改性方法，改性剂用量，CaCO3填充量对低密度聚乙烯（LDPE）材料与性能的影响。结果表明，7．5％的ENR－25湿法改性有效地改善了CaCO2在LDPE中的分散性及相容性，增强了界面作用强度，使材料在拉伸强度保持较高的情况下，拉伸弹性模量，撕裂强度和断裂伸长率得到有效的提高。     

In situ reactive compatibilization of polypropylene/epoxidized natural rubber blends by electron induced reactive processing: novel in‐line mixing technology

Blends of polypropylene (PP) and epoxidized natural rubber (ENR) were prepared by an in‐line electron induced reactive processing technique. The mixing was done in a Brabender mixing chamber coupled with an electron accelerator. The effect of sequence of electron treatment on the compatibilization of non‐polar PP and polar ENR was investigated in the presence of triallyl cyanurate (TAC). Finally, the resulting blends were characterized by different techniques, namely, Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), dynamic mechanical analysis (DMA), differential scanning calorimetry (DSC), tensile tests, and rheological studies. Generation of phase coupling and chemical compatibilization were observed from FTIR analysis. DMA studies showed enhanced high‐temperature modulus (above the glass transition temperature of both components) followed up by lowering in the tan δ peak. Rheological studies showed increase in modulus at low frequencies. Electron treatment and incorporation of rubber phase into PP showed significant effect on the degree of crystallinity of the blends, which was characterized by DSC study. The results obtained from FTIR, DMA, SEM, rheological studies, and tensile tests strongly affirmed that electron induced reactive processing of PP in presence of TAC before adding of ENR performed the best amongst all samples modified with electrons investigated in this study. Copyright © 2010 John Wiley & Sons, Ltd.     

Water absorption and enzymatic degradation of poly(lactic acid)/rice starch composites

Poly(lactic acid) (PLA) composites consisting of PLA, rice starch (RS) (0–50 wt%) and epoxidised natural rubber (ENR50) were compounded by a twin-screw extruder and compression moulded into dumbbell specimens. Tensile tests were performed to characterize the mechanical properties of the PLA/RS composites. Morphological studies were done on the tensile fractured surface of the specimens by using scanning electron microscopy (SEM). Twenty weight percent of RS achieved a good balance of strength and stiffness. Beyond 20 wt% loading of RS, the tensile strength and elongation at break of PLA decreased drastically. This may be attributed to the agglomeration of RS, which could then act as stress concentrator. The incorporation of ENR50 increased the tensile strength and elongation at break of the PLA/RS composites remarkably, owing to the elastomeric behaviour and compatibilisation effects of ENR50. Interestingly, the morphology of PLA/RS composites transformed to a more ductile one with the addition of ENR. The kinetics of water absorption of the PLA/RS composites conforms to Fick's law. The M_m and D values are dependent on the RS and ENR concentrations. The tensile properties of the PLA/RS composites deteriorated after water absorption. The retention-ability and recoverability of the PLA/RS composites are relatively low, attributed to the hydrolysis of PLA, degradation of the PLA–RS interface and leaching of the RS particles. In addition, the tensile properties of PLA/RS composites decreased drastically upon exposure to enzymatic degradation. Extensive pinhole and surface erosion on the PLA/RS composites indicate high degree of hydrolysis. Whilst the addition of ENR leads to some improvements in tensile properties, nevertheless, it enhanced the biodegradability of the PLA/RS composites when exposed to water and -amylase enzymatic treatments.     

Styrene Butadiene Rubber/Epoxidized Natural Rubber (SBR/ENR50) Nanocomposites Containing Nanoclay and Carbon Black as Fillers for Application in Tire-Tread Compounds

Nanocomposite vulcunizates based on a SBR/ENR50 (50/50%wt) rubber blend containing nanoclay (5 or 10 phr) with and without carbon black (CB 20 phr) were prepared by melt blending in an internal mixer. The compound containing 35 phr carbon black (only) was prepared as a reference sample. Microstructure of nanocomposite samples was investigated by using X-ray diffraction (XRD), melt rheo-mechanical spectroscopy (RMS), and scanning electron microscopy (SEM). The XRD patterns revealed that the distance between the clay layers were increased by adding CB to the nanocomposite samples; they caused better diffusion of chains between the layers and resulted in an intercalated structure. The RMS results also indicated the formation of the filler-filler networks. SEM images of fracture surfaces showed the presence of much roughness in the samples containing both nanoclay and CB compared to the other samples. The results obtained from application of the Flory–Rhener equation showed a high crosslink density for the sample with 10 phr nanoclay and 20 phr CB. Dynamic mechanical behavior, mechanical properties, and abrasion resistance of the nanocomposites were evaluated. The results indicated that the sample containing 10 phr nanoclay and 20 phr CB had an increased dynamic elastic modulus, reduced maximum loss factor (tanδ)_max,, and an improved tensile strength and abrasion resistance compared to the reference sample. Also, this sample showed the lowest maximum loss factor, at 50–60°C, so it can be a candidate for tire-tread application.     

Preparation and Study of Epoxidized Natural Rubber

Epoxidized natural rubbers (ENRs) with different extents of epoxidation (B) were prepared under various reaction conditions. The effects of the amount of H₂O₂ and the reaction time on B are discussed. The glass transition temperature T_g, the thermal degradation temperature and the activation energy of thermal degradation of the ENRs increase with B. The results indicate that the thermal stability of the ENRs increases with B.This revised version was published online in November 2005 with corrections to the Cover Date.     

A Comparative Study of the Dynamic-Mechanical Properties of Styrene Butadiene Rubber/Epoxidized Natural Rubber Dual Filler Nanocomposites Cured by Sulfur or Electron Beam Irradiation

The properties of (50/50?wt%) styrene butadiene rubber/epoxidized (50%) natural rubber (SBR/ENR50) blends containing nanoclay (NC, 5 or 10phr) without and with carbon black (CB 20phr) cured by sulfur or by electron beam (EB) irradiation (50 and 100kGy), were compared. A sulfur cured compound containing 35phr CB was prepared as a reference sample. Dynamic mechanical thermal analysis (DMTA) indicated that the sulfur cured sample containing 10phr NC and 20phr CB and the 100kGy irradiated sample with 5phr NC and 20phr CB had higher crosslink density, storage modulus, and tensile strength, and less loss factor and loss modulus, compared to the reference sample. Scanning electron microscopy (SEM) images of cryo- fractured surfaces confirmed the DMA and crosslink density results. We suggest a light weight 100kGy irradiated sample containing the lowest amount of NC and 20phr CB with a uniform distribution of the –C–C– bonds crosslinks, for high thermal stability applications and also for passenger cars tire treads, for its ice grip and wet skid properties especially for icy and wet roads, with improvements of 23% and 20%, respectively as compared to the reference sample.     

Effects of epoxidized natural rubber as a compatibilizer in melt compounded natural rubber-organoclay nanocomposites

Nanocomposites containing natural rubber (NR) as matrix, epoxidized natural rubber (ENR) as compatibilizer and organophilic layered clay (organoclay) as filler were produced in an internal mixer and cured using a conventional sulphuric system. The effects of ENR with 25 (ENR 25) and 50 mol% epoxidation (ENR 50), respectively, were compared at 5 and 10 parts per hundred rubber (phr) concentrations. The organoclay content was fixed at 2 phr. Cure characteristics, clay dispersion, (thermo)mechanical properties of the nanocomposites were determined and discussed. Incorporation of ENR and organoclay strongly affected the parameters which could be derived from Monsanto MDR measurements. Faster cure and increased crosslink density were attributed to changes in the activation/crosslinking pathway which was, however, not studied in detail. The organoclay was mostly intercalated according to X-ray diffraction (XRD) and transmission electron microscopic (TEM) results. The best clay dispersion was achieved by adding ENR 50. This was reflected in the stiffness of the nanocomposites derived from both dynamic mechanical thermal analysis (DMTA) and tensile tests. The tensile and tear strengths of the ENR 50 containing nanocomposites were also superior to the ENR 25 compatibilized and uncompatibilized stocks.