Electrochemical Characteristics of Mg0.9Ti0.1-xZrxNi （x=0.02, 0.04, 0.06） Alloys

Mg-based hydrogen storage alloys Mg0.9Ti0.1-xZrxNi (x=0.02, 0.04, 0.06) were successfully prepared by means of mechanical alloying (MA). The effects of Zr addition on the discharge capacity and the cycle performance of the Mg-based electrodes were also studied. It was found that the discharge capacities were improved with addition of a small amount of Zr and the cycle performances of the alloy were stabilized with the addition of Ti. The effects of surface modification or coating on the properties of Mg0.9Ti0.06Zr0.04Ni were also studied. The results indicated that coating with graphite improved both the discharge capacity and cycle life of the amorphous Mg0.9Ti0.06Zr0.04Ni electrode.     

Green Synthesis and Characterization of Cobalt Oxide Nanoparticles Using Psidium guajava Leaves Extracts and Their Photocatalytic and Biological Activities

The advanced technology for synthesizing nanoparticles utilizes natural resources in an environmentally friendly manner. Additionally, green synthesis is preferred to chemical and physical synthesis because it takes less time and effort. The green synthesis of cobalt oxide nanoparticles has recently risen due to its physico-chemical properties. In this study, many functional groups present in Psidium guajava leaf extracts are used to stabilize the synthesis of cobalt oxide nanoparticles. The biosynthesized cobalt oxide nanoparticles were investigated using UV-visible spectroscopic analysis. Additionally, Fourier-transform infrared spectroscopy revealed the presence of carboxylic acids, hydroxyl groups, aromatic amines, alcohols and phenolic groups. The X-ray diffraction analysis showed various peaks ranging from 32.35 to 67.35°, and the highest intensity showed at 36.69°. The particle size ranged from 26 to 40 nm and confirmed the average particle size is 30.9 nm. The green synthesized P. guajava cobalt oxide nanoparticles contain cobalt as the major abundant element, with 42.26 wt% and 18.75 at% confirmed by the EDAX techniques. SEM images of green synthesized P. guajava cobalt oxide nanoparticles showed agglomerated and non-uniform spherical particles. The anti-bacterial activity of green synthesized P. guajava cobalt oxide nanoparticles was evaluated against Gram-positive Staphylococcus aureus and Gram-negative Escherichia coli with a 7 to 18 mm inhibitory zone. The photocatalytic activity was evaluated using green synthesized P. guajava cobalt oxide nanoparticles and observed 79% of dye degradation. The MTT assay of P. guajava cobalt oxide nanoparticles showed an excellent cytotoxic effect against MCF 7 and HCT 116 cells compared to normal cells. The percentage of cell viability of P. guajava cobalt oxide nanoparticles was observed as 90, 83, 77, 68, 61, 58 and 52% for MCF-7 cells and 82, 70, 63, 51, 43, 40, and 37% for HCT 116 cells at the concentration of 1.53, 3.06, 6.12, 12.24, 24.48, 50, and 100 μg/mL compared to control cells. These results confirmed that green synthesized P. guajava cobalt oxide nanoparticles have a potential photocatalytic and anti-bacterial activity and also reduced cell viability against MCF-7 breast cancer and HCT 116 colorectal cancer cells.     

Choline chloride – Urea deep eutectic solvent an efficient media for the preparation of metal nanoparticles

Metal nanoparticles are nanosized structures that have different potential applications in biological, chemical, medical, and agricultural fields because of their exotic characteristics. Their size ranges from 1 to 100 nm. Metal nanoparticles are either purer forms of metals (eg: Gold, Silver, Copper, Iron, etc.) or their compounds (eg: sulfides, hydroxides, oxides, etc.). Ionic liquids are generally used in the extraction of nanoparticles but they are challenging because of their indigent bio-degradability, bio-compatibility, and sustainability. So Deep Eutectic Solvent (DES) is reported as an alternative to ionic liquids in the formation of nanoparticles. The DESs are a complex of quaternary ammonium salts and hydrogen donors or metal salt. DESs contain higher non-symmetric ions which have lower lattice energy and hence they have a lower melting point. This research utilizes a novel DES (choline chloride – urea) as an effective solvent to produce mercuric sulfide (HgS), zirconium oxide (ZrO), manganese oxide (MnO), and copper oxide (CuO) nanoparticles. As a result, the production of these metal nanoparticles using Choline Chloride (C₅H₁₄ClNO) – Urea DES can be treated as a promising way in chemical manufacturing. The nanoparticles have been analyzed using Ultra Violet Spectroscopy, Scanning Electron Microscopy (SEM), Transmission Electron Microscopy (TEM), Fourier Transform Infrared Spectroscopy (FT-IR), X-Ray Diffraction (XRD) and Energy Dispersive X-Ray Analysis (EDAX).     

钼镍镀层的制备及其光谱性能（英文）

采用电沉积法在镍合金表面制备钼镍镀层。研究钼镍镀层的硬度、磨损质量和摩擦系数、热膨胀等性能。分别用发射光谱法、能谱法、扫描电镜法和X衍射法等对钼镍镀层进行表征。在镍合金表面镀上一层钼镍镀层,可使其的硬度和耐磨性大幅度提高并减小磨擦系数,钼镍镀层的硬度为518 HV,比镍合金的硬度(300 HV)提高了72.67%;钼镍镀层的磨损质量是镍合金的磨损质量的1/1.94;镍合金和钼镍镀层的磨擦系数分别为0.640和0.559。镍合金的物理热膨胀曲线在100~120℃温度范围和570~640℃范围形成了2个峰,镍合金+钼镍镀层的物理热膨胀曲线在570~640℃范围形成了1个峰。在570~640℃范围可明显改善其热膨胀,镍合金+钼镍镀层的物理热膨胀曲线在570~640℃范围形成的峰远比镍合金的物理热膨胀曲线在570~640℃范围形成的峰小,可能是因为钼进入到镍的晶格中,抑制了镍在570~640℃范围发生晶格转变(bcc→fcc)所致。镍合金+钼镍镀层的物理热膨胀曲线在595~625℃范围形成的小峰,可能是由于MoNi_4和MoNi由半晶型结构转变为晶型结构所致。     

Effect of solvent volume on the physical properties of undoped and fluorine doped tin oxide films deposited using a low-cost spray technique

Undoped and fluorine doped tin oxide films were deposited from starting solutions having different values of solvent volume (10-50 ml) by employing a low cost and simplified spray technique using perfume atomizer. X-ray diffraction studies showed that there was a change in the preferential orientation from (2 1 1) plane to (1 1 0) plane as the volume of the solvent was increased. The sheet resistance (R_sh) of undoped SnO₂ film was found to be minimum (13.58 KΩ/□) when the solvent volume was lesser (10 ml) and there was a sharp increase in R_sh for higher values of solvent volume. Interestingly, it was observed that while the R_sh increases sharply with the increase in solvent volume for undoped SnO₂ films, it decreases gradually in the case of fluorine doped SnO₂ films. The quantitative analysis of EDAX confirmed that the electrical resistivity of the sprayed tin oxide film was mainly governed by the number of oxygen vacancies and the interstitial incorporation of Sn atoms which in turn was governed by the impinging flux on the hot substrate. The films were found to have good optical characteristics suitable for opto-electronic devices.     

Role of Cu concentration on the structure and transport properties of Cr-Zn ferrites

The influence of Cu concentration on the transport and microstructure characteristics of Cu_yZn_1−yCr_0.8Fe_1.2O₄ with 0.2≤y≤1 ferrite was studied. X-ray, energy dispersive X- ray (EDAX) and infrared spectra (IR) were carried out to assure the formation of the sample in the proper form. The dielectric constant (ε′) and ac conductivity were measured at different frequencies ranging from 600 kHz to 5 MHz from room temperature up to 800 K. The obtained data reveals that, a single phase cubic spinel structure for all the concentrations. From the results of IR spectra, mainly two bands were observed. The dielectric constant and the dielectric loss tangent decrease with increasing frequency and Cu concentration. The dielectric constant shows a dispersion peak (ε′_max) which shifts to higher frequency with increasing the temperature. The results are explained as due to the fact that the dielectric polarization process is similar to that of conduction. The appearance of the dispersion peak is related to the contribution of two types of charge carriers.     

Effect of Co doping on CIS2 thin films

In recent years, substantial scientific attention has been focused on renewable energy resources, which utilize natural resources for the production of electrical energy. Chalcopyrite semiconductors are used as one of the alternatives, Cu(In,Ga)Se₂ (CIGS) and CuInS₂ (CIS) are used for the fabrication of solar cells. These materials possess various properties Viz. ideal band gap (1.5?eV), high optical absorption, low light degradation, high radiation resistance, etc., hence they are suitable in the fabrication of solar cells. In contrast to other chalcopyrates, CuInS₂ is nontoxic, low-cost and easy to prepare by simple deposition techniques. Several impurities were doped to CuInS₂ bulks, to control conduction and also to obtain low resistivity. In this context, the structural, morphological and optical properties are reported for cobalt-doped CuInS₂ (CIS₂) thin films prepared by electro-deposition technique at room temperature. In the present study, we have used different cobalt concentration in the range of 0–5?wt.%. Doping of cobalt does not lead to the formation of any secondary phase, either in the form of metallic clusters or impurity complexes. However, with increase in cobalt concentration a decrease in the optical band gap, from 2.10 to 1.53?eV, is observed. In addition, implantation of cobalt in the CIS₂ gave changes in structural and surface properties of the thin films obtained. These thin films are also subjected to elemental analysis using EDAX.     

Preparation and characterization of electrodeposited indium selenide thin films

Indium Selenide (InSe) thin films were deposited from a mixture of Indium chloride and selenium dioxide in aqueous solution by electrodeposition technique on Indium Tin oxide coated glass substrates. The effects of the parameters during deposition such as current density, deposition potential versus saturated calomel electrode, pH value and concentration of source material were studied. X‐ray diffraction studies were carried out on the films to analyze the microstructure using an x‐ray diffractometer and were examined by RAMAN spectroscopy. The Raman peak position did not change much with chemical concentrations. Raman scattering due to the (LO) phonon was observed at 211 cm^–1. Optical absorption studies were performed with a double beam ultra violet‐visible –NIR spectrophotometer in the wavelength 300–1100 nm. The surface morphology of the layer was examined using a scanning electron micrograph. The composition of the films was studied using an Energy Dispersive Analysis by X‐Rays (EDAX).     

燃烧法合成La_2Zr_2O_7粉及其光谱性能

以La_2O_3,Zr(NO_3)_4和甘氨酸为原料,采用燃烧法合成La_2Zr_2O_7粉。分别用发射光谱法(ICPAES)、能谱法(EDAX)、X衍射法(XRD)、红外光谱法(IR)和热重-差热法(TG-DTA)等对La_2Zr_2O_7粉进行表征。分别研究了热处理温度对La_2Zr_2O_7粉的X衍射谱和红外光谱的影响。La_2Zr_2O_7粉的ICP-AES和EDAX分析结果表明,用燃烧法可合成出La_2Zr_2O_7粉。不同温度热处理后La_2Zr_2O_7粉的XRD分析结果表明,当热处理温度为600℃时,出现一个衍射峰,且衍射峰较宽,该结构为半晶型结构;提高热处理温度,衍射峰逐渐尖锐,峰形变窄,衍射峰逐渐增多;热处理温度在750~800℃范围,可得到烧绿石结构的La_2Zr_2O_7粉。在650~750℃热处理后La_2Zr_2O_7粉的红外光谱分析结果与XRD分析结果相同,热处理温度为750℃时,可得到烧绿石结构的La_2Zr_2O_7粉。La_2Zr_2O_7粉的TG-DTG分析结果表明,在120~1 600℃范围,La_2Zr_2O_7粉的结构稳定。     

Study of the structural phase transformation,and optical behavior of the as synthesized ZnO–SnO2–TiO2 nanocomposite

Bulk nanocomposites ZnO–SnO₂–TiO₂ were synthesized by solid-state reaction method. The X-ray diffraction patterns and Raman spectra of bulk nanocomposite as a function of sintering temperature (700 °C–1300 °C) indicate that the structural phases of SnO₂ and TiO₂ depend on the sintering temperature while the ZnO retains its hexagonal wurtzite phase at all sintering temperatures and SnO₂ started to transform into SnO at 900 °C and completely converted into SnO at 1100 °C, whereas the titanium dioxide (TiO₂) exhibits its most stable phase such as rutile at low sintering temperature (≤900°C) and it transforms partially into brookite phase at high sintering temperature (≥ 900 °C). The optical band gap of nanocomposite ZnO–SnO₂–TiO₂ sintered at 700 °C, 900 °C, 1100 °C and 1300 °C for 16 hours is calculated using the transformed diffuse reflectance ultra violet visible near infra red (UV–VisNIR) spectra and has been found to be 3.28, 3.29, 3.31 and 3.32 eV, respectively.