Human-to-metal electrostatic discharge current measurements – Notes on the ESD current waveform

The Electrostatic Discharge (ESD) phenomenon has been described through the IEC 61000-4-2. ESD current parameters' values, have been set in this Standard. The theoretical ESD current waveform defined in this standard, describing the conventional Contact discharge mode, needs to be re-evaluated on the basis of accurate experimental data. Even though the standard deals with commercial ESD generators, its goal is to simulate the natural phenomenon as good as possible. More and accurate data may contribute to the better simulation of the natural phenomenon. New values and better comprehension of the phenomenon demand new measurements based on high end measuring equipment. Such works and publications have been carried out the past years. Yet, the need to systematize and integrate this work remains. Larger and trust-worthy series of measurements need to be carried out and presented clearly.This paper deals with new ESD-current data, taken with broadband equipment. New and more detailed measurements like these, were never before taken at such a large number of individuals. The goal of this work is that the data acquired can serve as a basis for re-evaluating the conventional approach of the scientific community to the ESD event.In this paper, using a broadband measuring system, new parameters' values are measured and relations are presented, following standard statistical procedures. The results, which occur from measurements carried out on tenths of human individuals, are questioning the Standard in many points. A new way of approaching the standardization of the ESD current is proposed, as the excuse of the poor measuring equipment that sets barriers on the measuring accuracy, does not apply any more. The charging voltages of 500 V and 1000 V were also examined since such range of voltages are often met at ESD events and they are considered very harmful.     

Gas-phase 21Ne NMR studies and the nuclear magnetic dipole moment of neon-21

Gas-phase ²¹Ne nuclear magnetic resonance spectra were measured at the natural abundance of ²¹Ne isotope for samples consisting of pressurized neon up to 60 bar at room temperature and applying the magnetic field of the strength B₀ = 11.7574 T. It showed that the nuclear magnetic resonance frequency is linearly dependent on the density of gaseous neon. The resonance frequency was extrapolated to the zero-density point, and it permitted the determination of the ²¹Ne nuclear magnetic moment, μ(²¹Ne) = 0.6617774(10) μ_N. The present value of μ(²¹Ne) is not influenced by the bulk magnetic susceptibility of neon and interactions between neon atoms; therefore, it is more precise and reliable than the previous result obtained for μ(²¹Ne).     

Simulated annealing with noisy or imprecise energy measurements

The annealing algorithm (Ref. 1) is modified to allow for noisy or imprecise measurements of the energy cost function. This is important when the energy cannot be measured exactly or when it is computationally expensive to do so. Under suitable conditions on the noise/imprecision, it is shown that the modified algorithm exhibits the same convergence in probability to the globally minimum energy states as the annealing algorithm (Ref. 2). Since the annealing algorithm will typically enter and exit the minimum energy states infinitely often with probability one, the minimum energy state visited by the annealing algorithm is usually tracked. The effect of using noisy or imprecise energy measurements on tracking the minimum energy state visited by the modified algorithms is examined.The research reported here has been supported under Contracts AFOSR-85-0227, DAAG-29-84-K-0005, and DAAL-03-86-K-0171 and a Purdue Research Initiation Grant.     

Electrical conduction and dielectric properties of vanadium phosphate glasses doped with lithium

AC conductivity and dielectric studies on vanadium phosphate glasses doped with lithium have been carried out in the frequency range 0.2-100 kHz and temperature range 290-493 K. The frequency dependence of the conductivity at higher frequencies in glasses obeys a power relationship, σ_ac=Aω^s. The obtained values of the power s lie in the range 0.5≤s≤1 for both undoped and doped with low lithium content which confirms the electron hopping between V⁴⁺ and V⁵⁺ ions. For doped glasses with high lithium content, the values of s≤0.5 which confirm the domination of ionic conductivity. The study of frequency dependence of both dielectric constant and dielectric loss showed a decrease with increasing frequency while they increase with increasing temperature. The results have been explained on the basis of frequency assistance of electron hopping besides the ionic polarization of the glasses. The bulk conductivity increases with increasing temperature whereas decreases with increasing lithium content which means a reduction of the V⁵⁺.     

介质加载环板慢波结构高频特性研究

 提出了一种适用于环板结构的计算等效相对介电常数的方法，利用变分法导出了介质加载环板慢波结构的色散方程和耦合阻抗表达式。计算结果表明，介质加载能够有效降低环板慢波结构的工作电压。计算结果与CST-MWS的模拟结果吻合良好，说明所提出的计算等效相对介电常数的方法和计算色散方程的方法对环板慢波结构是切实可行的。     

Frequency dependence of ionic conductivity and dielectric relaxation studies in Na3H(SO4)2 single crystal

Electrical impedance measurements of Na₃H(SO₄)₂ were performed as a function of both temperature and frequency. The electrical conductivity and dielectric relaxation have been evaluated. The temperature dependence of electrical conductivity reveals that the sample crystals transformed to the fast ionic state in the high temperature phase. The dynamical disordering of hydrogen and sodium atoms and the orientation of SO₄ tetrahedra results in fast ionic conductivity. In addition to the proton conduction, the possibility of a Na⁺ contribution to the conductivity in the high temperature phase is proposed. The frequency dependence of AC conductivity is proportional to ω^s. The value of the exponent, s, lies between 0.85 and 0.46 in the room temperature phase, whereas it remains almost constant, 0.6, in the high-temperature phase. The dielectric dispersion is examined using the modulus formalism. An Arrhenius-type behavior is observed when the crystal undergoes the structural phase transition.     

Dielectric properties of a hydrated sulfonated poly(styrene-ethylene/butylenes-styrene) triblock copolymer

The present study showed that sulfonated poly(styrene-ethylene/butylenes-styrene) (S-SEBS) triblock copolymer ionomers can be made to exhibit dielectric constants on the order of a hundreds thousand. Although they are too lossy at this point to use as dielectric materials in capacitors or as electrostrictive Maxwell effect transducer materials because of their high hydrogen ion conductivity, the results of these initial dielectric studies as a function of ion content were used to try to understand the effects of a polar plasticizer, water, on dielectric properties of the acid form of this ionomer. This was done before moving on to more tightly bound ions (rather than the hydrogen ions of the sulfonic acid groups used here) and to other polar, less mobile plasticizers (which also interact strongly with the ionic dipoles). The discovery of such high dielectric constants suggested the possibility that low dielectric loss versions of this type of polymer, as well as other members of the class known as ionomers, might find future applications as extremely high dielectric constant materials in capacitors or transducers. Experimental results for films with degrees of sulfonation on the order of 10% or more showed dielectric constants on the order of ?′ ∼ 100,000 but dielectric loss tangents near D = tan δ ∼ 0.3, when the materials were exposed to high humidity conditions. Experiments to determine the effects of water content on the material's dielectric response showed that water can easily move into and out of the films studied and that this transport behavior is strongly correlated to the relative humidity of the environment and to the degree of sulfonation. Water content, in this case, was thus the primary consideration when attempting to understand the observed high dielectric constants in films with degree of sulfonation greater than 5.5%. However, vacuum-dried films were, also, examined and observed to exhibit a dielectric constant on the order of 2 until the degree of sulfonation was greater than 11%. Above this value, the dielectric constant increased by approximately 100% to a value on the order of 4.     

On additives, morphological evolution and dielectric breakdown in low density polyethylene

A series of low density polyethylene systems has been studied with respect to structural evolution and short-term dielectric breakdown behaviour. All materials were based upon a single polymer, that is commonly used in high voltage applications, but with different additives. In all three of these systems, multiple melting transitions were observed, as a result of molecular fractionation effects during crystallization. In the virgin polymer, a space-filling banded spherulitic morphology was found to develop at low temperatures (102 °C and below) whereas, at higher temperatures, only a few isolated axialites were observed. Inclusion of the antioxidant resulted in greatly increased nucleation densities, such that, at low temperatures, no evidence of spherulitic organisation remained. At higher temperatures, sheaf-like lamellar aggregates developed, which were much smaller and much more numerous than in the case of the virgin polymer. Further addition of dicumyl peroxide (DCP) resulted in the rapid formation of a crosslinked network at 200 °C. Some crosslinking also occurred at 150 °C, but over a much longer timescale. Where extensive crosslinking occurred prior to crystallization, the resulting gel inhibited structural development, such that only a few small, isolated sheaves were able to form at 102 °C. In view of the principal application area of this material, the breakdown strength of each of the above systems was then measured and the whole data set was analysed statistically. When structural factors were considered alongside the statistics, no clear trends emerged to indicate that either the compositional or morphological variations were reflected in the short-term electrical failure processes.     

New FIR laser lines and frequency measurements for optically pumped CD3OH

Twenty new cw FIR laser lines in CD₃OH, optically pumped by a CO₂ laser, are reported. The frequencies of 39 of the stronger laser lines were measured relative to stabilized CO₂ lasers with a fractional uncertainty, as determined by the reproducibility of the FIR frequency itself, of 2 parts in 10⁷.Contribution of the U.S. Government, not subject to copyright.     

A novel approach to the acoustic characterisation of porous road surfaces

Porous road surfaces offer an effective means of reducing the generation and propagation of noise from road traffic. However, the porosity of these surfaces can deteriorate over time, leading to a reduction in their noise reducing properties. Efficient methods are therefore required for monitoring this performance. Existing techniques for performing in-situ measurements of acoustic absorption are unsuitable for use within the traffic stream. Static measurements using time domain Maximum Length Sequence (MLS) based techniques have been demonstrated to offer advantages over traditional techniques, presenting the opportunity for measurements under dynamic conditions. This paper describes the design of a system for carrying out dynamic MLS-based measurements. Results are presented which demonstrate that stable dynamic measurements can be carried out at speeds of up to 30 km/h.