On additives, morphological evolution and dielectric breakdown in low density polyethylene

A series of low density polyethylene systems has been studied with respect to structural evolution and short-term dielectric breakdown behaviour. All materials were based upon a single polymer, that is commonly used in high voltage applications, but with different additives. In all three of these systems, multiple melting transitions were observed, as a result of molecular fractionation effects during crystallization. In the virgin polymer, a space-filling banded spherulitic morphology was found to develop at low temperatures (102 °C and below) whereas, at higher temperatures, only a few isolated axialites were observed. Inclusion of the antioxidant resulted in greatly increased nucleation densities, such that, at low temperatures, no evidence of spherulitic organisation remained. At higher temperatures, sheaf-like lamellar aggregates developed, which were much smaller and much more numerous than in the case of the virgin polymer. Further addition of dicumyl peroxide (DCP) resulted in the rapid formation of a crosslinked network at 200 °C. Some crosslinking also occurred at 150 °C, but over a much longer timescale. Where extensive crosslinking occurred prior to crystallization, the resulting gel inhibited structural development, such that only a few small, isolated sheaves were able to form at 102 °C. In view of the principal application area of this material, the breakdown strength of each of the above systems was then measured and the whole data set was analysed statistically. When structural factors were considered alongside the statistics, no clear trends emerged to indicate that either the compositional or morphological variations were reflected in the short-term electrical failure processes.     

Carbon-13 NMR evidence for cocrystallization of cellulose as a mechanism for hornification of bleached kraft pulp

Solid-state ¹³C NMR spectroscopy was used to characterize a bleached softwood kraft pulp in the never-dried state and after cycles of drying and remoistening. Changes in NMR signal strengths indicated that growth of crystalline domains involved cocrystallization rather than accretion of cellulose from noncrystalline domains. A cluster of C-4 signals at 89.4 ppm, assigned to the interiors of crystalline domains, grew at the expense of C-4 signals at 84.0 and 84.9 ppm, assigned to the well-ordered surfaces of crystalline domains. Irreversible changes were not detected until the moisture content dropped below 18%. They were enhanced by a second drying/remoistening cycle, but showed little further change on subsequent cycles. The necessary conditions resembled those reported for hornification, suggesting that cocrystallization might provide a mechanism for hornification.     

Photoluminescence activity of Yang and Secco etched multicrystalline silicon material

Ultraviolet and blue-green photoluminescence (PL) was investigated on multicrystalline silicon (mc-Si) samples chemically etched by Secco and Yang solutions. The samples were characterized by dislocation density (10⁵-10⁶ cm⁻²). The form of etched pits is triangular with Yang etch and like a honeycomb with Secco etch as observed with a scanning electron microscope (SEM). These textures of mc-Si wafers give a PL activity similar to that obtained with nanostructures of porous silicon (PS) as reported in the literature. The ultraviolet PL spectra observed with Yang etch shift to the blue-green spectrum range when applying Secco etch. In our experiments we have observed 3-5 μm diameter macro pores separated by a high density of nanowalls. These observations suggest that the origin of the PL activity are quantum dots resulting from the silicon nanocrystallites obtained after few minutes of chemical etching.     

Liquid phase oxidation of p-chlorotoluene to p-chlorobenzaldehyde over cobalt-doped mesoporous titania with a crystalline framework

Cobalt-doped mesoporous titania with a crystalline framework synthesized by surfactant templating method presented highly selective (99%) and reasonable conversion rate (49%) of catalytic oxidation of para-chlorotoluene to para-chlorobenzaldehyde in acetic acid using aqueous hydrogen peroxide as oxidant for the first time. Recycling of the catalyst indicates that the catalyst can be used a number of times without losing its activity to a greater extent. By contrast, cobalt-doped mesoporous titania without a crystalline structure and cobalt doped the commercial titania, Degussa P25 prepared by impregnation method with the similar concentration of cobalt were found inactive. The effects of catalyst concentration, reaction time, reaction temperature, and solvents on the performance of the catalyst were also investigated.     

SSIMS analysis of organics, polymer blends and interfaces

This paper gives a critical review on the applications of ToF SIMS in the areas of polymer additive characterization and in the study of polymer blends and interfaces. Polymer additives can readily be identified by ToF SIMS using their parent molecular ions or characteristic fragments. This analytical capability has been successfully applied to monitor the migration or segregation of additives during polymer processing. ToF SIMS is an ideal analytical tool for the study of polymer blends and interfaces because it is able to provide information on both surface composition and morphology. In combination with other analytical techniques such as AFM and XPS, ToF SIMS chemical imaging capability has opened up new horizons in the investigation of complex polymer blend systems. Finally the main advantages and limitations of ToF SIMS in these application areas are also discussed.     

正丁基苝四羧酸二酰亚胺的晶型和性能研究

文章合成了N,N'-二正丁基苝四羧酸二酰亚胺,并纯化、调晶,进行了IR、元素分析、X射线等测定.分析该化合物在DMF中的紫外光谱(最大吸收波长524.80 nm)、荧光光谱(最大发射波长539.0 nm)、Stokes位移(数值15 nm)等光谱性质.在400～700 nm范围内,α晶型薄膜紫外-可见吸收出现很强的吸收峰,且由β型变为α型,最大吸收波长有明显的红移(545 nm变为580 nm).X射线粉末衍射也反映出α晶型的2θ在26.0°处衍射峰CPS为2 508,β型在25.2°为1 891.α,β晶型作为电荷产生材料制得的功能分离型有机光导体,在光源滤波波长λ=532 nm曝光下,测得含α,β感光体达到饱和电位的时间分别为46,93.98 s,光衰电位(5.3千伏电压负充电电晕,1～2 s后的表面电位)分别为727和525 V,半衰曝光量分别为4.32,4.34μJ·cm-2,残余电位分别为30和45 V等光导性能数值.     

表面活性剂对均相沉淀法制备单晶Ce2O(CO3)2￠H2O微粉形貌及 形成机理的影响

在尿素及硝酸铈的混合溶液中分别加入表面活性剂CTAB、 PEG19000、OP-10,利用均相沉淀法合成了不同形貌的CeO2超细前驱体Ce2O(COa)2·H2O,采用X射线衍射及透射电子显微镜等测试手段,对产品的物相和形貌进行了表征．实验结果表明,所得产品均为斜方晶系的单晶Ce2O(CO3)2·H2O,且表面活性剂的加入使晶体的晶化程度明显提高;添加不同的表面活性剂得到不同形貌尺寸的产物: 阳离子型表面活性剂CTAB对Ce2O(CO3)2·H2O晶体的形貌影响不大,所得产物尺寸变小,且分散性得到一定的改善;非离子型表面活性剂对所得产物的形貌影响显著．加入PEG19000和OP-10分别得到了形状排列有序的、尺寸较均匀的、较规则无团聚的微米棒及具有紧密结合中心的发散状的花样微粒．不同形貌前驱体的形成与晶粒形成生长机理的改变有关．     

Structural and optical characterization of the propolis films

We have performed structural and optical characterizations of the propolis (an organic entity of biological nature) films grown on various non-organic substrates. The films were grown from a propolis melt or a propolis alcohol solution. The crystal structure has been observed in the films precipitated from the solution onto substrates such as an amorphous glass and sapphire or semiconductor indium monoselenide. For any growth method, the propolis film is a semiconductor with the bandgap of 3.07 eV at 300 K that is confirmed by a maximum in photoluminescence spectra at 2.86 eV. We argue that propolis films might be used in various optoelectronic device applications.     

CRYSTAL STRUCTURE AND MORPHOLOGY OF NASCENT SAMPLES OF SYMMETRIC AROMATIC POLYESTERS——Ⅱ. POLY(p-PHENYLENE 2,6-NAPHTHALATE)

Confined thin film melt polymerization (CTFMP) of naphthalene chloride/hydroquinone (NCMQ, 1/1, molar)mixtures at polymerization temperatures (T_p) below ca. 300℃ resulted in relatively thick, elongated crystals. Polymerizationof NC/HQ above 300℃ between glass yielded well-formed lamellar crystals ca. 100 A thick. Phase Ⅰ and Ⅱ [001] EDpatterns were obtained for all T_p, the relative amount of phase Ⅰ increasing with T_p. Polymerization of naphthalenedicarboxylic acid/hydroquinione diacetate 1/1 mixtures at high T_p also yielded lamellar crystals that "curled up" off of thesubstrate. When the high temperature CTFMP polymerization was conducted between mica, aggregates of lamellae on-edgedeveloped but epitaxial growth did not occur. Epitaxial growth of lamellae between mica could be obtained, however, byconfined thin film solution polymerization, with both of the latter samples yielding apparently related ED patterns from adifferent unit cell than phase Ⅰ or Ⅱ. Fiber patterns, obtained from sheared samples, indicated considerably greater crystaldisorder than in the nascent crystals. Refinement of the phase Ⅰ unit cell parameters, based on the [001] and [01 1] EDpatterns, with modeling based on Cerius~2, suggests a monoclinic phase Ⅰ unit cell with a = 7.76, b = 5.71, c = 14.99 A, α = γ= 90°, β= 99.7°, ρ = 1.47 g/cm~3, space group P12_1/al.     

Morphology-dependent photoluminescence property of red-emitting LnOCl:Eu (Ln=La and Gd)

Three different synthetic methods, the liquid phase process in HCl solution, the solvothermal reaction, and the surfactant-assisted solvothermal reaction, were explored to selectively control the particle shape and to enhance the luminescence intensity of the PbFCl-type red-emitting oxychloride phosphors LnOCl:Eu (Ln=La and Gd). The solvothermal pressure facilitated the low-temperature crystallization of the rod-shape particles for both Ln=La and Gd. It is noted that LaOCl:Eu nanorods show highly porous particle surface and quite low photoemission intensity. In contrast, the solvothermal synthesis could highly enhance the red-emission of GdOCl:Eu with no porous surface so as to be comparable to that of commercial Y₂O₃:Eu phosphor. An addition of surfactant material during solvothermal reaction yielded a rhomboidal-shape phosphor particles with no porous surface for both Ln=La and Gd. Interestingly, the elimination of surface porosity by using a surfactant significantly increased the emission intensity of LaOCl:Eu. It is proposed that the application of solvothermal technique for the synthesis of the PbFCl-type oxychloride phosphors is very effective to selectively control the particle shape and consequently to enhance the photoemission intensity if we use an appropriate surfactant material.